Revision as of 11:55, 6 May 2016

Overview

This tutorial shows how to use VPP lite to build a simple/toy IP4 LISP overlay on an Ubuntu host using namespaces and af_packet.

Requirements

• Ubuntu host
• ODL Beryllium

Topology

add pretty pic

Setup

Host and vpp and ODL configs

Host

Create namespace and set up interface in linux

# path to vpp executable and configurations folder
VPP_LITE_BIN=/home/vagrant/vpp/build-root/install-vpp_lite_debug-native/vpp/bin/vpp
VPP_LITE_CONF=/etc/vpp/lite/

# make sure there are no vpp instances running
pkill vpp
 
# delete previous incarnations if they exist
ip netns exec intervppns ifconfig vppbr down
ip netns exec intervppns brctl delbr vppbr
ip link del dev veth_vpp1 &> /dev/null
ip link del dev veth_vpp2 &> /dev/null
ip link del dev veth_intervpp1 &> /dev/null
ip link del dev veth_intervpp2 &> /dev/null
ip link del dev veth_odl &> /dev/null
ip netns del vppns1 &> /dev/null
ip netns del vppns2 &> /dev/null
ip netns del intervppns &> /dev/null
 
if [ "$1" == "clean" ] ; then
  exit 0;
fi

# create vpp to clients and inter-vpp namespaces
ip netns add vppns1
ip netns add vppns2
ip netns add intervppns

# create vpp and odl interfaces and set them in intervppns 
ip link add veth_intervpp1 type veth peer name intervpp1
ip link add veth_intervpp2 type veth peer name intervpp2
ip link add veth_odl type veth peer name odl
ip link set dev intervpp1 up
ip link set dev intervpp2 up
ip link set dev odl up
ip link set dev veth_intervpp1 up netns intervppns
ip link set dev veth_intervpp2 up netns intervppns
ip link set dev veth_odl up netns intervppns

# create bridge in intervppns and add vpp and odl interfaces 
ip netns exec intervppns brctl addbr vppbr
ip netns exec intervppns brctl addif vppbr veth_intervpp1
ip netns exec intervppns brctl addif vppbr veth_intervpp2
ip netns exec intervppns brctl addif vppbr veth_odl
ip netns exec intervppns ifconfig vppbr up
 
# create and configure 1st veth client to vpp pair
ip link add veth_vpp1 type veth peer name vpp1
ip link set dev vpp1 up
ip link set dev veth_vpp1 up netns vppns1
 
ip netns exec vppns1 \
  bash -c "
    ip link set dev lo up
    ip addr add 6.0.2.2/24 dev veth_vpp1
    ip route add 6.0.4.0/24 via 6.0.2.1
"
 
# create and configure 2nd veth client to vpp pair
ip link add veth_vpp2 type veth peer name vpp2
ip link set dev vpp2 up
ip link set dev veth_vpp2 up netns vppns2
 
ip netns exec vppns2 \
  bash -c "
    ip link set dev lo up
    ip addr add 6.0.4.4/24 dev veth_vpp2
    ip route add 6.0.2.0/24 via 6.0.4.1
"

# set odl iface ip and disable checksum offloading
ifconfig odl 6.0.3.100/24
ethtool --offload  odl rx off tx off

# start vpp1 and vpp2 in separate chroot
sudo $VPP_LITE_BIN \
  unix { log /tmp/vpp1.log cli-listen \
         localhost:5002 full-coredump \
         exec $VPP_LITE_CONF/vpp1.config } \
  api-trace { on } chroot {prefix xtr1}
 
sudo $VPP_LITE_BIN \
  unix { log /tmp/vpp2.log cli-listen \
         localhost:5003 full-coredump exec $VPP_LITE_CONF/vpp2.config } \
  api-trace { on } chroot {prefix xtr2}

vpp1 config

Create and configure the LAN and WAN facing af_packet interfaces

• Create LAN facing host-vpp1 and WAN facing host-intervpp1 interfaces
• Set 6.0.2.1/24 and 6.0.3.1 as their respective IP4 addresses

Enable and configure LISP-GPE:

• Set WAN facing interface host-vpp1 as locator (underlay attachment point)
• Set LAN facing prefix 6.0.2.0/24 as a local EID (End-host ID - overlay address)
• Configure map-server address 6.0.3.100

create host-interface name vpp1
set int state host-vpp1 up
set int ip address host-vpp1 6.0.2.1/24

create host-interface name intervpp1
set int state host-intervpp1 up
set int ip address host-intervpp1 6.0.3.1/24

lisp gpe enable

lisp locator-set add ls1 iface host-intervpp1 p 1 w 1
lisp eid-table add eid 6.0.2.0/24 locator-set ls1
lisp map-resolver add 6.0.3.100

vpp2 config

Create and configure the LAN and WAN facing af_packet interfaces

• Create LAN facing host-vpp2 and WAN facing host-intervpp2 interfaces
• Set 6.0.4.1/24 and 6.0.3.2 as their respective IP4 addresses

Enable and configure LISP-GPE:

• Set WAN facing interface host-vpp2 as locator (underlay attachment point)
• Set LAN facing prefix 6.0.4.0/24 as a local EID (End-host ID - overlay address)
• Configure map-server address 6.0.3.100

create host-interface name vpp2
set int state host-vpp2 up
set int ip address host-vpp2 6.0.4.1/24

create host-interface name intervpp2
set int state host-intervpp2 up
set int ip address host-intervpp1 6.0.3.2/24

lisp gpe enable

lisp locator-set add ls1 iface host-intervpp2 p 1 w 1
lisp eid-table add eid 6.0.4.0/24 locator-set ls1
lisp map-resolver add 6.0.3.100

ODL Map-Server/Resolver

Test

ip netns exec vppns1 ping 6.0.4.4