Revision as of 11:59, 6 May 2016

Overview

This tutorial shows how to use VPP lite to build a simple/toy IP4 LISP overlay on an Ubuntu host using namespaces and af_packet interfaces.

Requirements

• Ubuntu host
• ODL Beryllium

Topology

add pretty pic

Setup

This section explains how to build VPP lite and walks through the host, vpp and ODL configs

Build VPP lite

Host

Create namespace and set up interface in linux

# path to vpp executable and configurations folder
VPP_LITE_BIN=/home/vagrant/vpp/build-root/install-vpp_lite_debug-native/vpp/bin/vpp
VPP_LITE_CONF=/etc/vpp/lite/

# make sure there are no vpp instances running
pkill vpp
 
# delete previous incarnations if they exist
ip netns exec intervppns ifconfig vppbr down
ip netns exec intervppns brctl delbr vppbr
ip link del dev veth_vpp1 &> /dev/null
ip link del dev veth_vpp2 &> /dev/null
ip link del dev veth_intervpp1 &> /dev/null
ip link del dev veth_intervpp2 &> /dev/null
ip link del dev veth_odl &> /dev/null
ip netns del vppns1 &> /dev/null
ip netns del vppns2 &> /dev/null
ip netns del intervppns &> /dev/null
 
if [ "$1" == "clean" ] ; then
  exit 0;
fi

# create vpp to clients and inter-vpp namespaces
ip netns add vppns1
ip netns add vppns2
ip netns add intervppns

# create vpp and odl interfaces and set them in intervppns 
ip link add veth_intervpp1 type veth peer name intervpp1
ip link add veth_intervpp2 type veth peer name intervpp2
ip link add veth_odl type veth peer name odl
ip link set dev intervpp1 up
ip link set dev intervpp2 up
ip link set dev odl up
ip link set dev veth_intervpp1 up netns intervppns
ip link set dev veth_intervpp2 up netns intervppns
ip link set dev veth_odl up netns intervppns

# create bridge in intervppns and add vpp and odl interfaces 
ip netns exec intervppns brctl addbr vppbr
ip netns exec intervppns brctl addif vppbr veth_intervpp1
ip netns exec intervppns brctl addif vppbr veth_intervpp2
ip netns exec intervppns brctl addif vppbr veth_odl
ip netns exec intervppns ifconfig vppbr up
 
# create and configure 1st veth client to vpp pair
ip link add veth_vpp1 type veth peer name vpp1
ip link set dev vpp1 up
ip link set dev veth_vpp1 up netns vppns1
 
ip netns exec vppns1 \
  bash -c "
    ip link set dev lo up
    ip addr add 6.0.2.2/24 dev veth_vpp1
    ip route add 6.0.4.0/24 via 6.0.2.1
"
 
# create and configure 2nd veth client to vpp pair
ip link add veth_vpp2 type veth peer name vpp2
ip link set dev vpp2 up
ip link set dev veth_vpp2 up netns vppns2
 
ip netns exec vppns2 \
  bash -c "
    ip link set dev lo up
    ip addr add 6.0.4.4/24 dev veth_vpp2
    ip route add 6.0.2.0/24 via 6.0.4.1
"

# set odl iface ip and disable checksum offloading
ifconfig odl 6.0.3.100/24
ethtool --offload  odl rx off tx off

# start vpp1 and vpp2 in separate chroot
sudo $VPP_LITE_BIN \
  unix { log /tmp/vpp1.log cli-listen \
         localhost:5002 full-coredump \
         exec $VPP_LITE_CONF/vpp1.config } \
  api-trace { on } chroot {prefix xtr1}
 
sudo $VPP_LITE_BIN \
  unix { log /tmp/vpp2.log cli-listen \
         localhost:5003 full-coredump exec $VPP_LITE_CONF/vpp2.config } \
  api-trace { on } chroot {prefix xtr2}

vpp1 config

Create and configure the LAN and WAN facing af_packet interfaces

• Create LAN facing host-vpp1 and WAN facing host-intervpp1 interfaces
• Set 6.0.2.1/24 and 6.0.3.1 as their respective IP4 addresses

Enable and configure LISP-GPE:

• Set WAN facing interface host-vpp1 as locator (underlay attachment point)
• Set LAN facing prefix 6.0.2.0/24 as a local EID (End-host ID - overlay address)
• Configure map-server address 6.0.3.100

create host-interface name vpp1
set int state host-vpp1 up
set int ip address host-vpp1 6.0.2.1/24

create host-interface name intervpp1
set int state host-intervpp1 up
set int ip address host-intervpp1 6.0.3.1/24

lisp gpe enable

lisp locator-set add ls1 iface host-intervpp1 p 1 w 1
lisp eid-table add eid 6.0.2.0/24 locator-set ls1
lisp map-resolver add 6.0.3.100

vpp2 config

Create and configure the LAN and WAN facing af_packet interfaces

• Create LAN facing host-vpp2 and WAN facing host-intervpp2 interfaces
• Set 6.0.4.1/24 and 6.0.3.2 as their respective IP4 addresses

Enable and configure LISP-GPE:

• Set WAN facing interface host-vpp2 as locator (underlay attachment point)
• Set LAN facing prefix 6.0.4.0/24 as a local EID (End-host ID - overlay address)
• Configure map-server address 6.0.3.100

create host-interface name vpp2
set int state host-vpp2 up
set int ip address host-vpp2 6.0.4.1/24

create host-interface name intervpp2
set int state host-intervpp2 up
set int ip address host-intervpp1 6.0.3.2/24

lisp gpe enable

lisp locator-set add ls1 iface host-intervpp2 p 1 w 1
lisp eid-table add eid 6.0.4.0/24 locator-set ls1
lisp map-resolver add 6.0.3.100

ODL Map-Server/Resolver

Test

ip netns exec vppns1 ping 6.0.4.4