CSIT/Tutorials/Vagrant/Virtualbox/Ubuntu

From fd.io
Jump to: navigation, search

This page describes how to run the CSIT test suites on Ubuntu 14.04.

Prerequisites

This procedure requires the following software be installed on the host PRIOR to following the directions:

Install necessary packages as follows: 

cd /tmp
echo "deb http://download.virtualbox.org/virtualbox/debian $(lsb_release -c|cut -f2) contrib"|sudo tee -a /etc/apt/sources.list
wget http://download.virtualbox.org/virtualbox/debian/oracle_vbox.asc
sudo apt-key add oracle_vbox.asc
sudo apt-get update
sudo apt-get install -y --allow-unauthenticated git virtualbox-5.0 virtualenv vagrant python-dev python-crypto
vagrant plugin install vagrant-cachier

cd <CSIT repo directory>
export CSIT_DIR=$(pwd)


Optional 

cd <CSIT repo directory>
export VPP_DIR=$(pwd)

The following wiki page describes how to build VPP in a VM locally: Pulling, Building, Hacking, and Pushing VPP Code


Running behind a firewall

  • export http_proxy, https_proxy, HTTP_PROXY, HTTPS_PROXY bash environment variables.
  • vagrant-proxyconf (vagrant plugin install vagrant-proxyconf)

NOTE: It may be necessary to build vagrant-proxyconf locally and install it following the instructions on the vagrant-proxyconf wiki.


This guide was verified on a Cisco UCS C240 /w 64GB ram running Ubuntu 14.04. The standard 3 node CSIT topology consists of a traffic generator (tg) and two Device-Under-Test machines (dut1 and dut2).

This guide goes through setup of the management network that is interconnecting all VMs. This network is used by the test framework to connect to topology nodes and execute test code on them. Furthermore it explains how to start the Vagrant VMs, how to install prepared deb packages on DUTs, and how to start tests.

Start Vagrant VM environment

At the bash prompt, create a folder where your Vagrant environment is going to exist, and copy the Vagrantfile and install_debs.sh from ${CSIT_DIR}/resources/tools/vagrant into that folder. Also copy all of the vpp packages to be tested into the same folder. 

mkdir csit-vagrant
cd csit-vagrant
export CSIT_VAGRANT=$(pwd)
cp ${CSIT_DIR}/resources/tools/vagrant/* .
cp ${VPP_DIR}/build-root/vpp*.deb .
vagrant up --parallel --provision

Console output: 

Bringing machine 'tg' up with 'virtualbox' provider...
Bringing machine 'dut1' up with 'virtualbox' provider...
Bringing machine 'dut2' up with 'virtualbox' provider...
...

Vagrant will download base disk images and install the VPP debian packages to bring those machines to required state. VPP will NOT be started automatically.

Optionally, verify that VPP successfully starts on one of the dut VMs: 

vagrant ssh dut1
sudo service vpp start
sudo vppctl sh int
sudo cat /var/log/upstart/vpp.log
sudo service vpp stop
exit

Copy your ssh-key to Vagrant VMs

This steps has to be repeated every time your Vagrant VMs are re-created (i.e. vagrant destroy command was issued) 

echo csit@192.168.255.10{0,1,2} | xargs -n 1 ssh-copy-id

Respond with "csit" as password (without quotes). From now on you have password-less access from this account to csit@vagrant-vms via SSH.

Set up your virtualenv

cd ${CSIT_DIR}
rm -rf env
virtualenv env
source ./env/bin/activate
pip install -r requirements.txt

You should now see '(env) ' in front of your bash prompt: 

(env) <username>@<hostname>:csit$

Create topology file

CSIT framework uses YAML format to describe the nodes of the topology the testcases are going to run on. There are such data as IP addresses, login information, type of the node in the topology file. CSIT framework uses PCI addresses of the NICs on the topology nodes to map them to the node topology information. Luckily, PCI addresses stay at constant values in between "Vagrant up" cycles, therefore the PCI addresses are pre-stored for you in topologies/available/vagrant.yaml. BUT, within the test cases, and concretely in code that matches topology interfaces against VPP reported interfaces, MAC addreses are used. These are different every time you create new Vagrant instances of those VMs, therefore you have to scrape the PCI_ADDRESS to MAC_ADDRESS map from current topology instance.

Update your topology file with MAC addresses from current running VMs by running the following python script: 

cd ${CSIT_DIR}
export PYTHONPATH=$(pwd)
./resources/tools/topology/update_topology.py -f -v -o topologies/available/vagrant_pci.yaml topologies/available/vagrant.yaml

192.168.255.101: Found MAC address of PCI device 0000:00:0a.0: 08:00:27:66:a5:75
192.168.255.101: Found MAC address of PCI device 0000:00:09.0: 08:00:27:bf:ed:90
192.168.255.100: Found MAC address of PCI device 0000:00:0a.0: 08:00:27:ae:26:e9
192.168.255.100: Found MAC address of PCI device 0000:00:09.0: 08:00:27:50:cf:7e
192.168.255.102: Found MAC address of PCI device 0000:00:0a.0: 08:00:27:2c:25:6e
192.168.255.102: Found MAC address of PCI device 0000:00:09.0: 08:00:27:41:45:7d

Executing test cases for Vagrant setup

cd ${CSIT_DIR}
pybot -L TRACE -v TOPOLOGY_PATH:topologies/available/vagrant_pci.yaml --exclude 3_node_double_link_topoNOT3_node_single_link_topo --include VM_ENV --exclude PERFTEST tests/

This command executes tests with TRACE logging enabled, on the topology you just updated with proper MAC addresses, and starts only testcases that are made for single-link-topology (what we have in Vagrant currently), that are made for VM environment, and are not performance tests.

One can modify the above command to start for example only ipv4 tests: 

pybot -L TRACE -v TOPOLOGY_PATH:topologies/available/vagrant_pci.yaml -s ipv4 tests/

Or a single test case: 

pybot -L TRACE -v TOPOLOGY_PATH:topologies/available/vagrant_pci.yaml -t "VPP replies to ICMPv4 echo request" tests/

Install New VPP packages on DUTs

To test a different set of VPP packages, either built locally in ${VPP_DIR}/build-root or downloaded from [1]: 

${CSIT_VAGRANT}/install_debs.sh ${DIRECTORY_WITH_YOUR_VPP_PACKAGES}/vpp*.deb
Retrieved from "https://wiki.fd.io/index.php?title=CSIT/Tutorials/Vagrant/Virtualbox/Ubuntu&oldid=1702"