Difference between revisions of "CSIT/VPP-16.09 Test Report Draft"

From fd.io
Jump to: navigation, search
(→‎Long Performance Tests - NDR and PDR Search)
Line 1,546: Line 1,546:
 
=====Long Bridge Domain Intel-X520-DA2=====
 
=====Long Bridge Domain Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2BD test cases'''
+
*'''RFC2544: Pkt throughput L2BD test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 switching of IPv4.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 switching of IPv4.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 1,557: Line 1,557:
 
|TC01: 64B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps)  
+
|RATE: 7821428 pps (2x 3910714 pps) BANDWIDTH: 5.255 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.255999868 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/67),(10/24/87)
−
LAT_100%NDR: ['20/205/277', '40/232/319']
+
LAT_10%NDR:(10/20/69),(10/19/43)
−
LAT_50%NDR: ['10/23/67', '10/24/87']
+
−
LAT_10%NDR: ['10/20/69', '10/19/43']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps)  
+
|RATE: 7821428 pps (2x 3910714 pps) BANDWIDTH: 5.255 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.255999868 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/214/285 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/216/350 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/124),(20/28/123)
−
LAT_100%NDR: ['20/170/185', '20/153/172']
+
LAT_10%NDR:(20/26/78),(20/27/75)
−
LAT_50%NDR: ['20/26/124', '20/28/123']
+
−
LAT_10%NDR: ['20/26/78', '20/27/75']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/171/206 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/138/194 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/170),(50/64/168)
−
LAT_100%NDR: ['50/171/234', '50/211/236']
+
LAT_10%NDR:(50/58/119),(50/61/74)
−
LAT_50%NDR: ['50/63/170', '50/64/168']
+
−
LAT_10%NDR: ['50/58/119', '50/61/74']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/208/240 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/181/219 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 16366666.25 pps (2x 8183333.125 pps)  
+
|RATE: 16366666 pps (2x 8183333 pps) BANDWIDTH: 10.998 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.99839972 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/78),(10/28/78)
−
LAT_100%NDR: ['10/51/93', '10/943/1004']
+
LAT_10%NDR:(10/19/77),(10/18/73)
−
LAT_50%NDR: ['10/28/78', '10/28/78']
+
−
LAT_10%NDR: ['10/19/77', '10/18/73']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 16597618.625 pps (2x 8298809.3125 pps)  
+
|RATE: 16597618 pps (2x 8298809 pps) BANDWIDTH: 11.153 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.153599716 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/55/105 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1592/1645 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/107),(10/26/71)
−
LAT_100%NDR: ['20/203/231', '20/78/111']
+
LAT_10%NDR:(20/27/101),(10/26/57)
−
LAT_50%NDR: ['20/26/107', '10/26/71']
+
−
LAT_10%NDR: ['20/27/101', '10/26/57']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/148/203 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/169/191 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/102),(50/66/120)
−
LAT_100%NDR: ['50/133/176', '60/116/160']
+
LAT_10%NDR:(50/58/114),(50/61/101)
−
LAT_50%NDR: ['50/64/102', '50/66/120']
+
−
LAT_10%NDR: ['50/58/114', '50/61/101']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT L2BD - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/165/214 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/143/199 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/43),(10/18/38)
−
LAT_100%NDR: ['20/483/534', '10/484/555']
+
LAT_10%NDR:(10/17/75),(10/17/79)
−
LAT_50%NDR: ['10/18/43', '10/18/38']
+
−
LAT_10%NDR: ['10/17/75', '10/17/79']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23988094.625 pps (2x 11994047.3125 pps)  
+
|RATE: 23988094 pps (2x 11994047 pps) BANDWIDTH: 16.119 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.119999588 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/488/511 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/488/580 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/94),(20/27/92)
−
LAT_100%NDR: ['20/128/184', '20/131/172']
+
LAT_10%NDR:(20/25/76),(20/24/60)
−
LAT_50%NDR: ['20/26/94', '20/27/92']
+
−
LAT_10%NDR: ['20/25/76', '20/24/60']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/114/154 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/102/138 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/134),(50/65/126)
−
LAT_100%NDR: ['60/142/187', '50/116/153']
+
LAT_10%NDR:(50/60/95),(50/61/79)
−
LAT_50%NDR: ['50/65/134', '50/65/126']
+
−
LAT_10%NDR: ['50/60/95', '50/61/79']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT L2BD - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/122/196 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/122/174 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: IMIX_v4_1 PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|TC20: IMIX_v4_1 PDR binary search - DUT L2BD - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Bridge Domain Vhost Intel-X520-DA2=====
 
=====Long Bridge Domain Vhost Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2BD test cases with vhost'''
+
*'''RFC2544: Pkt throughput L2BD test cases with vhost'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 switching of IPv4.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 switching of IPv4.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 1,758: Line 1,695:
 
|TC01: 64B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 426627.59375 pps (2x 213313.796875 pps)  
+
|RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.286693743 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/618),(10/26/593)
−
LAT_100%NDR: ['10/28/356', '10/32/329']
+
LAT_10%NDR:(10/23/340),(10/22/350)
−
LAT_50%NDR: ['10/26/618', '10/26/593']
+
−
LAT_10%NDR: ['10/23/340', '10/22/350']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 2082182.79688 pps (2x 1041091.39844 pps)  
+
|RATE: 2082182 pps (2x 1041091 pps) BANDWIDTH: 1.399 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 1.3992268395 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/96/491 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/93/441 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 396285.78125 pps (2x 198142.890625 pps)  
+
|RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.8759002525 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/31/360),(20/35/116)
−
LAT_100%NDR: ['20/46/428', '20/50/201']
+
LAT_10%NDR:(20/31/319),(20/30/91)
−
LAT_50%NDR: ['20/31/360', '20/35/116']
+
−
LAT_10%NDR: ['20/31/319', '20/30/91']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1224114.5 pps (2x 612057.25 pps)  
+
|RATE: 1224114 pps (2x 612057 pps) BANDWIDTH: 15.061 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.061504808 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 30/481/862 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/483/768 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC05: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 309964.5625 pps (2x 154982.28125 pps)  
+
|RATE: 309964 pps (2x 154982 pps) BANDWIDTH: 0.927 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.927000676651 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|TC06: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 1692409.9375 pps (2x 846204.96875 pps)  
+
|RATE: 1692409 pps (2x 846204 pps) BANDWIDTH: 5.061 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.06143394129 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 978479.328124 pps (2x 489239.664062 pps)  
+
|RATE: 978479 pps (2x 489239 pps) BANDWIDTH: 0.657 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.657538108499 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/348),(10/25/96)
−
LAT_100%NDR: ['10/28/334', '10/32/130']
+
LAT_10%NDR:(10/22/334),(10/21/82)
−
LAT_50%NDR: ['10/27/348', '10/25/96']
+
−
LAT_10%NDR: ['10/22/334', '10/21/82']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 3011617.29688 pps (2x 1505808.64844 pps)  
+
|RATE: 3011617 pps (2x 1505808 pps) BANDWIDTH: 2.023 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 2.0238068235 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/64/151 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/64/438 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 772571.5625 pps (2x 386285.78125 pps)  
+
|RATE: 772571 pps (2x 386285 pps) BANDWIDTH: 9.505 Gbps (untagged)
−
FINAL_BANDWIDTH: 9.505720505 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/34/372),(20/37/145)
−
LAT_100%NDR: ['20/41/389', '20/44/122']
+
LAT_10%NDR:(20/29/326),(20/31/91)
−
LAT_50%NDR: ['20/34/372', '20/37/145']
+
−
LAT_10%NDR: ['20/29/326', '20/31/91']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/381/416 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/467/611 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC11: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 492551.6875 pps (2x 246275.84375 pps)  
+
|RATE: 492551 pps (2x 246275 pps) BANDWIDTH: 1.473 Gbps (untagged)
−
FINAL_BANDWIDTH: 1.47305790028 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|TC12: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 3309610.1875 pps (2x 1654805.09375 pps)  
+
|RATE: 3309610 pps (2x 1654805 pps) BANDWIDTH: 9.897 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 9.89794077916 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 397582.765624 pps (2x 198791.382812 pps)  
+
|RATE: 397582 pps (2x 198791 pps) BANDWIDTH: 0.267 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.267175618499 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/331),(10/22/86)
−
LAT_100%NDR: ['10/22/353', '10/25/91']
+
LAT_10%NDR:(10/23/333),(10/19/67)
−
LAT_50%NDR: ['10/23/331', '10/22/86']
+
−
LAT_10%NDR: ['10/23/333', '10/19/67']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 4667172.5 pps (2x 2333586.25 pps)  
+
|RATE: 4667172 pps (2x 2333586 pps) BANDWIDTH: 3.136 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.13633992 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/54/128 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/71/417 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 396285.78125 pps (2x 198142.890625 pps)  
+
|RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.8759002525 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/31/77),(20/33/402)
−
LAT_100%NDR: ['20/33/106', '20/37/371']
+
LAT_10%NDR:(20/30/89),(20/30/340)
−
LAT_50%NDR: ['20/31/77', '20/33/402']
+
−
LAT_10%NDR: ['20/30/89', '20/30/340']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/266/582 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/246/329 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC17: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 1170732.4375 pps (2x 585366.21875 pps)  
+
|RATE: 1170732 pps (2x 585366 pps) BANDWIDTH: 3.501 Gbps (untagged)
−
FINAL_BANDWIDTH: 3.5012704452 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|TC18: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 3909539.3125 pps (2x 1954769.65625 pps)  
+
|RATE: 3909539 pps (2x 1954769 pps) BANDWIDTH: 11.692 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.6921287997 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: 64B NDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq
 
|TC19: 64B NDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 368537.9375 pps (2x 184268.96875 pps)  
+
|RATE: 368537 pps (2x 184268 pps) BANDWIDTH: 0.247 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.247657494 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/363),(10/27/358)
−
LAT_100%NDR: ['10/32/333', '10/33/357']
+
LAT_10%NDR:(10/22/337),(10/22/358)
−
LAT_50%NDR: ['10/28/363', '10/27/358']
+
−
LAT_10%NDR: ['10/22/337', '10/22/358']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: 64B PDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq
 
|TC20: 64B PDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 2082182.79688 pps (2x 1041091.39844 pps)  
+
|RATE: 2082182 pps (2x 1041091 pps) BANDWIDTH: 1.399 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 1.3992268395 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/93/491 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/98/244 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Cop Intel-X520-DA2=====
 
=====Long IPv4 Cop Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 whitelist test cases'''
+
*'''RFC2544: Pkt throughput IPv4 whitelist test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 1,959: Line 1,827:
 
|TC01: 64B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps)  
+
|RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.79039988 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/144),(10/28/174)
−
LAT_100%NDR: ['10/3549/3644', '10/1917/2167']
+
LAT_10%NDR:(10/20/56),(10/17/68)
−
LAT_50%NDR: ['10/28/144', '10/28/174']
+
−
LAT_10%NDR: ['10/20/56', '10/17/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps)  
+
|RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.79039988 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1894/1996 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1722/3686 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/29/125),(10/28/81)
−
LAT_100%NDR: ['20/261/291', '20/214/255']
+
LAT_10%NDR:(20/25/127),(10/24/155)
−
LAT_50%NDR: ['20/29/125', '10/28/81']
+
−
LAT_10%NDR: ['20/25/127', '10/24/155']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/253/272 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/235/261 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/126),(50/64/158)
−
LAT_100%NDR: ['60/213/253', '50/205/221']
+
LAT_10%NDR:(50/61/126),(50/61/117)
−
LAT_50%NDR: ['50/64/126', '50/64/158']
+
−
LAT_10%NDR: ['50/61/126', '50/61/117']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/211/258 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/194/239 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 13826190.125 pps (2x 6913095.0625 pps)  
+
|RATE: 13826190 pps (2x 6913095 pps) BANDWIDTH: 9.291 Gbps (untagged)
−
FINAL_BANDWIDTH: 9.291199764 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/21/102),(10/22/47)
−
LAT_100%NDR: ['10/44/106', '10/60/109']
+
LAT_10%NDR:(10/18/65),(10/16/47)
−
LAT_50%NDR: ['10/21/102', '10/22/47']
+
−
LAT_10%NDR: ['10/18/65', '10/16/47']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 13826190.125 pps (2x 6913095.0625 pps)  
+
|RATE: 13826190 pps (2x 6913095 pps) BANDWIDTH: 9.291 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 9.291199764 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 2/42/183 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/169/321 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/144),(10/26/111)
−
LAT_100%NDR: ['20/139/156', '20/196/230']
+
LAT_10%NDR:(10/26/88),(10/25/83)
−
LAT_50%NDR: ['10/25/144', '10/26/111']
+
−
LAT_10%NDR: ['10/26/88', '10/25/83']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/127/148 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/248/283 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/193),(50/65/151)
−
LAT_100%NDR: ['50/225/288', '60/133/166']
+
LAT_10%NDR:(50/60/114),(50/58/109)
−
LAT_50%NDR: ['50/64/193', '50/65/151']
+
−
LAT_10%NDR: ['50/60/114', '50/58/109']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/237/286 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/134/168 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/141),(10/20/94)
−
LAT_100%NDR: ['10/927/974', '10/936/968']
+
LAT_10%NDR:(10/19/75),(10/18/41)
−
LAT_50%NDR: ['10/20/141', '10/20/94']
+
−
LAT_10%NDR: ['10/19/75', '10/18/41']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/485/547 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/555/594 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/59),(10/26/94)
−
LAT_100%NDR: ['20/165/178', '10/155/200']
+
LAT_10%NDR:(10/24/75),(10/26/65)
−
LAT_50%NDR: ['10/26/59', '10/26/94']
+
−
LAT_10%NDR: ['10/24/75', '10/26/65']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/106/121 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/121/153 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/31/112),(50/32/131)
−
LAT_100%NDR: ['50/148/195', '50/116/187']
+
LAT_10%NDR:(50/61/111),(50/60/106)
−
LAT_50%NDR: ['50/31/112', '50/32/131']
+
−
LAT_10%NDR: ['50/61/111', '50/60/106']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/129/193 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/143/162 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Fib 200k Intel-X520-DA2=====
 
=====Long IPv4 Fib 200k Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 2,141: Line 1,955:
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)  
+
|RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/76),(10/20/83)
−
LAT_100%NDR: ['10/816/1762', '20/1504/3096']
+
LAT_10%NDR:(10/19/46),(10/19/64)
−
LAT_50%NDR: ['10/20/76', '10/20/83']
+
−
LAT_10%NDR: ['10/19/46', '10/19/64']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)  
+
|RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 40/1604/1669 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/3031/3098 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/133),(10/28/132)
−
LAT_100%NDR: ['20/225/611', '20/260/582']
+
LAT_10%NDR:(10/25/45),(10/24/67)
−
LAT_50%NDR: ['10/27/133', '10/28/132']
+
−
LAT_10%NDR: ['10/25/45', '10/24/67']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/244/777 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/203/758 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/159),(50/63/154)
−
LAT_100%NDR: ['50/230/329', '50/250/316']
+
LAT_10%NDR:(50/60/91),(50/60/114)
−
LAT_50%NDR: ['50/62/159', '50/63/154']
+
−
LAT_10%NDR: ['50/60/91', '50/60/114']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/263/339 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/275/304 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 17983332.875 pps (2x 8991666.4375 pps)  
+
|RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)
−
FINAL_BANDWIDTH: 12.084799692 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/50),(10/23/51)
−
LAT_100%NDR: ['10/48/126', '10/72/198']
+
LAT_10%NDR:(10/19/65),(10/18/67)
−
LAT_50%NDR: ['10/23/50', '10/23/51']
+
−
LAT_10%NDR: ['10/19/65', '10/18/67']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 18214285.25 pps (2x 9107142.625 pps)  
+
|RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.239999688 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/48/656 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/810/1435 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/120),(10/27/154)
−
LAT_100%NDR: ['20/157/192', '20/165/191']
+
LAT_10%NDR:(10/25/82),(10/26/96)
−
LAT_50%NDR: ['10/25/120', '10/27/154']
+
−
LAT_10%NDR: ['10/25/82', '10/26/96']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/237/257 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/113/135 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/184),(50/63/129)
−
LAT_100%NDR: ['50/254/297', '50/128/155']
+
LAT_10%NDR:(50/60/153),(50/60/100)
−
LAT_50%NDR: ['50/63/184', '50/63/129']
+
−
LAT_10%NDR: ['50/60/153', '50/60/100']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/252/313 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/118/146 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/41),(10/18/35)
−
LAT_100%NDR: ['20/478/580', '10/930/990']
+
LAT_10%NDR:(10/18/37),(10/17/59)
−
LAT_50%NDR: ['10/18/41', '10/18/35']
+
−
LAT_10%NDR: ['10/18/37', '10/17/59']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/930/1008 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/479/645 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/167),(10/26/71)
−
LAT_100%NDR: ['20/105/171', '20/121/141']
+
LAT_10%NDR:(10/25/75),(10/23/53)
−
LAT_50%NDR: ['10/27/167', '10/26/71']
+
−
LAT_10%NDR: ['10/25/75', '10/23/53']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/146/758 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/66/631 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/117),(50/64/116)
−
LAT_100%NDR: ['50/139/175', '50/124/147']
+
LAT_10%NDR:(50/60/109),(50/59/105)
−
LAT_50%NDR: ['50/64/117', '50/64/116']
+
−
LAT_10%NDR: ['50/60/109', '50/59/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/193/233 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/116/140 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Fib 20k Intel-X520-DA2=====
 
=====Long IPv4 Fib 20k Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 2,323: Line 2,083:
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)  
+
|RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/167),(10/26/167)
−
LAT_100%NDR: ['20/1605/1693', '10/3037/3148']
+
LAT_10%NDR:(10/20/64),(10/19/46)
−
LAT_50%NDR: ['10/26/167', '10/26/167']
+
−
LAT_10%NDR: ['10/20/64', '10/19/46']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)  
+
|RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/1602/1661 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/3017/3097 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/150),(10/27/144)
−
LAT_100%NDR: ['20/227/274', '20/227/276']
+
LAT_10%NDR:(10/25/125),(10/23/93)
−
LAT_50%NDR: ['10/27/150', '10/27/144']
+
−
LAT_10%NDR: ['10/25/125', '10/23/93']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/243/298 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/191/200 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/667),(50/65/631)
−
LAT_100%NDR: ['50/225/251', '50/213/273']
+
LAT_10%NDR:(50/57/108),(50/61/98)
−
LAT_50%NDR: ['50/63/667', '50/65/631']
+
−
LAT_10%NDR: ['50/57/108', '50/61/98']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/206/222 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/246/291 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 17983332.875 pps (2x 8991666.4375 pps)  
+
|RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)
−
FINAL_BANDWIDTH: 12.084799692 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/62),(10/27/53)
−
LAT_100%NDR: ['10/41/652', '20/60/629']
+
LAT_10%NDR:(10/18/36),(10/19/55)
−
LAT_50%NDR: ['10/20/62', '10/27/53']
+
−
LAT_10%NDR: ['10/18/36', '10/19/55']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 18214285.25 pps (2x 9107142.625 pps)  
+
|RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.239999688 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/49/112 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1449/1500 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/87),(10/26/52)
−
LAT_100%NDR: ['20/265/819', '20/117/588']
+
LAT_10%NDR:(10/25/107),(10/23/78)
−
LAT_50%NDR: ['10/26/87', '10/26/52']
+
−
LAT_10%NDR: ['10/25/107', '10/23/78']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/229/747 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/117/622 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/130),(50/63/181)
−
LAT_100%NDR: ['50/217/250', '60/166/230']
+
LAT_10%NDR:(50/59/77),(50/60/100)
−
LAT_50%NDR: ['50/63/130', '50/63/181']
+
−
LAT_10%NDR: ['50/59/77', '50/60/100']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/232/279 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/127/148 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/17/35),(10/17/41)
−
LAT_100%NDR: ['10/482/536', '10/491/542']
+
LAT_10%NDR:(10/18/86),(10/17/27)
−
LAT_50%NDR: ['10/17/35', '10/17/41']
+
−
LAT_10%NDR: ['10/18/86', '10/17/27']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/928/1020 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/478/547 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/95),(10/25/101)
−
LAT_100%NDR: ['20/146/170', '20/67/120']
+
LAT_10%NDR:(10/25/671),(10/26/633)
−
LAT_50%NDR: ['10/26/95', '10/25/101']
+
−
LAT_10%NDR: ['10/25/671', '10/26/633']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/107/125 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/160/204 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/683),(50/64/652)
−
LAT_100%NDR: ['60/125/168', '50/129/160']
+
LAT_10%NDR:(50/60/92),(50/60/90)
−
LAT_50%NDR: ['50/63/683', '50/64/652']
+
−
LAT_10%NDR: ['50/60/92', '50/60/90']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/106/153 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/120/180 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Fib 2M Intel-X520-DA2=====
 
=====Long IPv4 Fib 2M Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 2,505: Line 2,211:
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)  
+
|RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/9/64),(10/10/59)
−
LAT_100%NDR: ['20/1605/1758', '30/3043/3169']
+
LAT_10%NDR:(10/19/67),(10/18/48)
−
LAT_50%NDR: ['10/9/64', '10/10/59']
+
−
LAT_10%NDR: ['10/19/67', '10/18/48']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps)  
+
|RATE: 8283333 pps (2x 4141666 pps) BANDWIDTH: 5.566 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.56639986 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/54/161 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/55/180 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/157),(10/27/126)
−
LAT_100%NDR: ['20/256/308', '20/191/213']
+
LAT_10%NDR:(10/25/56),(10/25/58)
−
LAT_50%NDR: ['10/26/157', '10/27/126']
+
−
LAT_10%NDR: ['10/25/56', '10/25/58']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/275/294 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/302/360 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/168),(50/65/183)
−
LAT_100%NDR: ['50/175/253', '60/260/313']
+
LAT_10%NDR:(50/57/109),(50/60/112)
−
LAT_50%NDR: ['50/64/168', '50/65/183']
+
−
LAT_10%NDR: ['50/57/109', '50/60/112']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/212/235 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/255/289 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 17983332.875 pps (2x 8991666.4375 pps)  
+
|RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)
−
FINAL_BANDWIDTH: 12.084799692 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/17/61),(10/21/72)
−
LAT_100%NDR: ['20/43/141', '10/76/242']
+
LAT_10%NDR:(10/19/37),(10/18/99)
−
LAT_50%NDR: ['10/17/61', '10/21/72']
+
−
LAT_10%NDR: ['10/19/37', '10/18/99']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 18214285.25 pps (2x 9107142.625 pps)  
+
|RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.239999688 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/47/124 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/1454/1491 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/112),(10/26/57)
−
LAT_100%NDR: ['20/258/291', '20/129/165']
+
LAT_10%NDR:(10/26/104),(10/26/61)
−
LAT_50%NDR: ['10/27/112', '10/26/57']
+
−
LAT_10%NDR: ['10/26/104', '10/26/61']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/279/299 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/95/152 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/120),(50/65/149)
−
LAT_100%NDR: ['50/117/148', '60/257/292']
+
LAT_10%NDR:(50/60/113),(50/60/103)
−
LAT_50%NDR: ['50/62/120', '50/65/149']
+
−
LAT_10%NDR: ['50/60/113', '50/60/103']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/116/138 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/178/216 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/17/48),(10/17/45)
−
LAT_100%NDR: ['10/598/664', '10/474/548']
+
LAT_10%NDR:(10/17/123),(10/16/70)
−
LAT_50%NDR: ['10/17/48', '10/17/45']
+
−
LAT_10%NDR: ['10/17/123', '10/16/70']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/930/941 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/478/584 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/152),(10/27/97)
−
LAT_100%NDR: ['20/152/235', '20/100/125']
+
LAT_10%NDR:(10/25/80),(10/26/70)
−
LAT_50%NDR: ['10/25/152', '10/27/97']
+
−
LAT_10%NDR: ['10/25/80', '10/26/70']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/148/214 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/98/142 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/61/145),(50/65/126)
−
LAT_100%NDR: ['50/115/139', '50/135/173']
+
LAT_10%NDR:(50/60/95),(50/60/96)
−
LAT_50%NDR: ['50/61/145', '50/65/126']
+
−
LAT_10%NDR: ['50/60/95', '50/60/96']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/107/202 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/99/163 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 iAcl Intel-X520-DA2=====
 
=====Long IPv4 iAcl Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 iAcl whitelist test cases'''
+
*'''RFC2544: Pkt throughput IPv4 iAcl whitelist test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 2,687: Line 2,339:
 
|TC01: 64B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps)  
+
|RATE: 6897618 pps (2x 3448809 pps) BANDWIDTH: 4.635 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.635199884 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/148),(10/27/111)
−
LAT_100%NDR: ['10/61/202', '10/63/210']
+
LAT_10%NDR:(10/19/52),(10/18/114)
−
LAT_50%NDR: ['10/25/148', '10/27/111']
+
−
LAT_10%NDR: ['10/19/52', '10/18/114']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps)  
+
|RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.79039988 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/3581/3663 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 40/1906/2042 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/29/141),(10/27/140)
−
LAT_100%NDR: ['20/243/259', '20/202/243']
+
LAT_10%NDR:(20/26/81),(10/26/108)
−
LAT_50%NDR: ['20/29/141', '10/27/140']
+
−
LAT_10%NDR: ['20/26/81', '10/26/108']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/244/261 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/192/232 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/160),(50/64/154)
−
LAT_100%NDR: ['50/197/305', '50/211/241']
+
LAT_10%NDR:(50/57/152),(50/61/148)
−
LAT_50%NDR: ['50/63/160', '50/64/154']
+
−
LAT_10%NDR: ['50/57/152', '50/61/148']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/164/196 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/204/227 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 12902380.625 pps (2x 6451190.3125 pps)  
+
|RATE: 12902380 pps (2x 6451190 pps) BANDWIDTH: 8.670 Gbps (untagged)
−
FINAL_BANDWIDTH: 8.67039978 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/22/99),(10/22/148)
−
LAT_100%NDR: ['20/38/65', '10/50/138']
+
LAT_10%NDR:(10/18/74),(10/18/54)
−
LAT_50%NDR: ['10/22/99', '10/22/148']
+
−
LAT_10%NDR: ['10/18/74', '10/18/54']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 13133333.0 pps (2x 6566666.5 pps)  
+
|RATE: 13133333 pps (2x 6566666 pps) BANDWIDTH: 8.825 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 8.825599776 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/25/112 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/513/1096 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/74),(10/25/164)
−
LAT_100%NDR: ['20/166/185', '20/249/263']
+
LAT_10%NDR:(10/25/63),(10/25/83)
−
LAT_50%NDR: ['20/25/74', '10/25/164']
+
−
LAT_10%NDR: ['10/25/63', '10/25/83']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/143/165 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/193/214 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/191),(50/65/124)
−
LAT_100%NDR: ['50/223/301', '50/113/171']
+
LAT_10%NDR:(50/61/175),(50/61/96)
−
LAT_50%NDR: ['50/64/191', '50/65/124']
+
−
LAT_10%NDR: ['50/61/175', '50/61/96']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/165/186 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/213/239 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)  
+
|RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/36),(10/18/36)
−
LAT_100%NDR: ['10/108/236', '10/48/121']
+
LAT_10%NDR:(10/9/115),(10/9/55)
−
LAT_50%NDR: ['10/18/36', '10/18/36']
+
−
LAT_10%NDR: ['10/9/115', '10/9/55']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)  
+
|RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/525/895 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/675/699 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/76),(10/26/89)
−
LAT_100%NDR: ['20/105/127', '20/143/194']
+
LAT_10%NDR:(10/13/61),(10/11/80)
−
LAT_50%NDR: ['20/25/76', '10/26/89']
+
−
LAT_10%NDR: ['10/13/61', '10/11/80']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/166/218 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/131/146 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/174),(50/63/140)
−
LAT_100%NDR: ['50/161/247', '50/130/162']
+
LAT_10%NDR:(50/57/116),(50/60/92)
−
LAT_50%NDR: ['50/64/174', '50/63/140']
+
−
LAT_10%NDR: ['50/57/116', '50/60/92']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/124/179 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/138/162 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Intel-X520-DA2=====
 
=====Long IPv4 Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv4 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 2,869: Line 2,467:
 
|TC01: 64B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8745237.875 pps (2x 4372618.9375 pps)  
+
|RATE: 8745237 pps (2x 4372618 pps) BANDWIDTH: 5.876 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.876799852 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/19/164),(10/34/144)
−
LAT_100%NDR: ['10/140/268', '10/154/266']
+
LAT_10%NDR:(10/18/88),(10/18/72)
−
LAT_50%NDR: ['10/19/164', '10/34/144']
+
−
LAT_10%NDR: ['10/18/88', '10/18/72']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8745237.875 pps (2x 4372618.9375 pps)  
+
|RATE: 8745237 pps (2x 4372618 pps) BANDWIDTH: 5.876 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.876799852 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/1527/1604 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1530/1614 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/149),(10/27/131)
−
LAT_100%NDR: ['20/199/252', '20/235/259']
+
LAT_10%NDR:(10/25/73),(10/26/126)
−
LAT_50%NDR: ['10/27/149', '10/27/131']
+
−
LAT_10%NDR: ['10/25/73', '10/26/126']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/135/176 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/156/225 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/121),(50/65/126)
−
LAT_100%NDR: ['50/102/748', '60/100/712']
+
LAT_10%NDR:(50/61/119),(50/60/73)
−
LAT_50%NDR: ['50/65/121', '50/65/126']
+
−
LAT_10%NDR: ['50/61/119', '50/60/73']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/187/575 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/245/468 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 18214285.25 pps (2x 9107142.625 pps)  
+
|RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged)
−
FINAL_BANDWIDTH: 12.239999688 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/11/79),(10/15/166)
−
LAT_100%NDR: ['20/49/622', '20/1434/2010']
+
LAT_10%NDR:(10/18/40),(10/19/66)
−
LAT_50%NDR: ['10/11/79', '10/15/166']
+
−
LAT_10%NDR: ['10/18/40', '10/19/66']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 18214285.25 pps (2x 9107142.625 pps)  
+
|RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.239999688 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/45/621 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/753/1337 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/96),(10/26/125)
−
LAT_100%NDR: ['20/192/212', '20/185/207']
+
LAT_10%NDR:(10/25/91),(10/25/93)
−
LAT_50%NDR: ['20/26/96', '10/26/125']
+
−
LAT_10%NDR: ['10/25/91', '10/25/93']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/190/206 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/180/237 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/170),(50/65/189)
−
LAT_100%NDR: ['60/140/172', '50/184/231']
+
LAT_10%NDR:(50/57/102),(50/60/85)
−
LAT_50%NDR: ['50/63/170', '50/65/189']
+
−
LAT_10%NDR: ['50/57/102', '50/60/85']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/228/282 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/114/150 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/662),(10/17/633)
−
LAT_100%NDR: ['10/930/988', '10/478/561']
+
LAT_10%NDR:(10/18/74),(10/17/49)
−
LAT_50%NDR: ['10/18/662', '10/17/633']
+
−
LAT_10%NDR: ['10/18/74', '10/17/49']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/929/1077 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/478/557 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/71),(10/26/96)
−
LAT_100%NDR: ['20/147/694', '20/109/674']
+
LAT_10%NDR:(10/25/37),(10/24/47)
−
LAT_50%NDR: ['10/26/71', '10/26/96']
+
−
LAT_10%NDR: ['10/25/37', '10/24/47']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/144/738 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/103/704 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/101),(50/64/112)
−
LAT_100%NDR: ['50/140/192', '50/119/179']
+
LAT_10%NDR:(50/57/110),(50/60/109)
−
LAT_50%NDR: ['50/64/101', '50/64/112']
+
−
LAT_10%NDR: ['50/57/110', '50/60/109']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/123/143 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/122/189 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: IMIX_v4_1 NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC19: IMIX_v4_1 NDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: IMIX_v4_1 PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|TC20: IMIX_v4_1 PDR binary search - DUT IPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Policer Intel-X520-DA2=====
 
=====Long IPv4 Policer Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 policer test cases'''
+
*'''RFC2544: Pkt throughput IPv4 policer test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544, RFC2698.
 
*'''[Ref] Applicable standard specifications:''' RFC2544, RFC2698.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,070: Line 2,605:
 
|TC01: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps.
−
|FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps)  
+
|RATE: 6897618 pps (2x 3448809 pps) BANDWIDTH: 4.635 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.635199884 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/87),(10/25/172)
−
LAT_100%NDR: ['10/30/177', '10/32/216']
+
LAT_10%NDR:(10/20/50),(10/17/34)
−
LAT_50%NDR: ['10/24/87', '10/25/172']
+
−
LAT_10%NDR: ['10/20/50', '10/17/34']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
−
|FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps)  
+
|RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.79039988 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/2305/2702 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/2297/2533 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/30/164),(10/30/164)
−
LAT_100%NDR: ['20/208/231', '20/273/290']
+
LAT_10%NDR:(20/13/112),(10/12/118)
−
LAT_50%NDR: ['20/30/164', '10/30/164']
+
−
LAT_10%NDR: ['20/13/112', '10/12/118']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/268/317 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/243/311 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/157),(50/62/138)
−
LAT_100%NDR: ['50/186/246', '60/220/241']
+
LAT_10%NDR:(50/61/142),(50/60/111)
−
LAT_50%NDR: ['50/63/157', '50/62/138']
+
−
LAT_10%NDR: ['50/61/142', '50/60/111']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1  phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/184/222 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/209/228 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps.
−
|FINAL_RATE: 12671428.25 pps (2x 6335714.125 pps)  
+
|RATE: 12671428 pps (2x 6335714 pps) BANDWIDTH: 8.515 Gbps (untagged)
−
FINAL_BANDWIDTH: 8.515199784 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/22/98),(10/22/157)
−
LAT_100%NDR: ['10/42/143', '20/1055/1165']
+
LAT_10%NDR:(10/18/39),(10/18/68)
−
LAT_50%NDR: ['10/22/98', '10/22/157']
+
−
LAT_10%NDR: ['10/18/39', '10/18/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
−
|FINAL_RATE: 12671428.25 pps (2x 6335714.125 pps)  
+
|RATE: 12671428 pps (2x 6335714 pps) BANDWIDTH: 8.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 8.515199784 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/48/103 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1057/1093 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/76),(10/26/119)
−
LAT_100%NDR: ['20/100/135', '20/242/261']
+
LAT_10%NDR:(10/26/65),(10/23/55)
−
LAT_50%NDR: ['20/27/76', '10/26/119']
+
−
LAT_10%NDR: ['10/26/65', '10/23/55']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/134/151 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/189/214 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/221),(50/64/128)
−
LAT_100%NDR: ['50/217/235', '60/183/227']
+
LAT_10%NDR:(50/57/101),(50/60/156)
−
LAT_50%NDR: ['50/62/221', '50/64/128']
+
−
LAT_10%NDR: ['50/57/101', '50/60/156']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2  phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/164/209 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/116/142 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64  Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 22140475.625 pps (2x 11070237.8125 pps)  
+
|RATE: 22140475 pps (2x 11070237 pps) BANDWIDTH: 14.878 Gbps (untagged)
−
FINAL_BANDWIDTH: 14.87839962 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/77),(10/21/101)
−
LAT_100%NDR: ['10/105/418', '10/164/256']
+
LAT_10%NDR:(10/18/34),(10/17/82)
−
LAT_50%NDR: ['10/20/77', '10/21/101']
+
−
LAT_10%NDR: ['10/18/34', '10/17/82']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64  Byte frames using binary search start at 10GE linerate, step  100kpps, LT=0.5%.
−
|FINAL_RATE: 17521428.125 pps (2x 8760714.0625 pps)  
+
|RATE: 17521428 pps (2x 8760714 pps) BANDWIDTH: 11.774 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.7743997 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/220/1120 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/38/207 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518  Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/12/91),(20/12/106)
−
LAT_100%NDR: ['20/102/154', '20/179/228']
+
LAT_10%NDR:(10/25/42),(10/26/76)
−
LAT_50%NDR: ['20/12/91', '20/12/106']
+
−
LAT_10%NDR: ['10/25/42', '10/26/76']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518  Byte frames using binary search start at 10GE linerate, step  10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/129/186 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/143/218 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/115),(50/65/118)
−
LAT_100%NDR: ['50/159/247', '50/125/161']
+
LAT_10%NDR:(50/57/124),(50/57/97)
−
LAT_50%NDR: ['50/62/115', '50/65/118']
+
−
LAT_10%NDR: ['50/57/124', '50/57/97']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4  phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000  Byte frames using binary search start at 10GE linerate, step 5kpps,  LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/106/165 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/121/244 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv4 Vhost Intel-X520-DA2=====
 
=====Long IPv4 Vhost Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv4 test cases with vhost'''
+
*'''RFC2544: Pkt throughput IPv4 test cases with vhost'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for IPv4 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to mac, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to mac, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,252: Line 2,733:
 
|TC01: 64B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 339493.109376 pps (2x 169746.554688 pps)  
+
|RATE: 339493 pps (2x 169746 pps) BANDWIDTH: 0.228 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.228139369501 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/78),(10/23/354)
−
LAT_100%NDR: ['10/28/107', '10/29/394']
+
LAT_10%NDR:(10/23/46),(10/22/353)
−
LAT_50%NDR: ['10/23/78', '10/23/354']
+
−
LAT_10%NDR: ['10/23/46', '10/22/353']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1995048.3125 pps (2x 997524.15625 pps)  
+
|RATE: 1995048 pps (2x 997524 pps) BANDWIDTH: 1.340 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 1.340672466 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/116/486 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/121/549 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 446457.21875 pps (2x 223228.609375 pps)  
+
|RATE: 446457 pps (2x 223228 pps) BANDWIDTH: 5.493 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.4932096195 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/36/463),(20/37/152)
−
LAT_100%NDR: ['20/69/473', '20/71/253']
+
LAT_10%NDR:(20/30/402),(20/31/60)
−
LAT_50%NDR: ['20/36/463', '20/37/152']
+
−
LAT_10%NDR: ['20/30/402', '20/31/60']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1199028.78125 pps (2x 599514.390625 pps)  
+
|RATE: 1199028 pps (2x 599514 pps) BANDWIDTH: 14.752 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 14.7528501245 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/401/706 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/398/743 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC05: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 257796.8125 pps (2x 128898.40625 pps)  
+
|RATE: 257796 pps (2x 128898 pps) BANDWIDTH: 0.770 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.770984327042 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|TC06: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 1248984.0625 pps (2x 624492.03125 pps)  
+
|RATE: 1248984 pps (2x 624492 pps) BANDWIDTH: 3.735 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.73529496961 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 455672.421876 pps (2x 227836.210938 pps)  
+
|RATE: 455672 pps (2x 227836 pps) BANDWIDTH: 0.306 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.306211867501 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/97),(10/25/347)
−
LAT_100%NDR: ['10/25/105', '10/29/367']
+
LAT_10%NDR:(10/21/164),(10/23/352)
−
LAT_50%NDR: ['10/24/97', '10/25/347']
+
−
LAT_10%NDR: ['10/21/164', '10/23/352']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 3708693.17188 pps (2x 1854346.58594 pps)  
+
|RATE: 3708693 pps (2x 1854346 pps) BANDWIDTH: 2.492 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 2.4922418115 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/92/432 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/98/184 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 396285.78125 pps (2x 198142.890625 pps)  
+
|RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.8759002525 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/33/377),(20/34/98)
−
LAT_100%NDR: ['20/41/484', '20/38/137']
+
LAT_10%NDR:(20/30/340),(20/31/84)
−
LAT_50%NDR: ['20/33/377', '20/34/98']
+
−
LAT_10%NDR: ['20/30/340', '20/31/84']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/317/330 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/479/836 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC11: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 414300.0625 pps (2x 207150.03125 pps)  
+
|RATE: 414300 pps (2x 207150 pps) BANDWIDTH: 1.239 Gbps (untagged)
−
FINAL_BANDWIDTH: 1.23903337587 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|TC12: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 3557407.0 pps (2x 1778703.5 pps)  
+
|RATE: 3557407 pps (2x 1778703 pps) BANDWIDTH: 10.639 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 10.6390184398 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 426627.59375 pps (2x 213313.796875 pps)  
+
|RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.286693743 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/71),(10/22/74)
−
LAT_100%NDR: ['10/22/212', '10/26/82']
+
LAT_10%NDR:(10/22/189),(10/19/52)
−
LAT_50%NDR: ['10/23/71', '10/22/74']
+
−
LAT_10%NDR: ['10/22/189', '10/19/52']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 4086275.9375 pps (2x 2043137.96875 pps)  
+
|RATE: 4086275 pps (2x 2043137 pps) BANDWIDTH: 2.745 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 2.74597743 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/57/402 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/82/177 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 371200.0625 pps (2x 185600.03125 pps)  
+
|RATE: 371200 pps (2x 185600 pps) BANDWIDTH: 4.567 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.567245569 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/32/356),(20/32/364)
−
LAT_100%NDR: ['20/33/389', '20/36/426']
+
LAT_10%NDR:(20/27/383),(20/31/331)
−
LAT_50%NDR: ['20/32/356', '20/32/364']
+
−
LAT_10%NDR: ['20/27/383', '20/31/331']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/274/547 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/431/646 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC17: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 857725.9375 pps (2x 428862.96875 pps)  
+
|RATE: 857725 pps (2x 428862 pps) BANDWIDTH: 2.565 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.56517234754 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|TC18: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 3622616.6875 pps (2x 1811308.34375 pps)  
+
|RATE: 3622616 pps (2x 1811308 pps) BANDWIDTH: 10.834 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 10.8340388768 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 Cop Intel-X520-DA2=====
 
=====Long IPv6 Cop Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 whitelist test cases'''
+
*'''RFC2544: Pkt throughput IPv6 whitelist test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,434: Line 2,852:
 
|TC01: 78B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 6132079.0625 pps (2x 3066039.53125 pps)  
+
|RATE: 6132079 pps (2x 3066039 pps) BANDWIDTH: 4.807 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.807549985 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/75),(10/25/74)
−
LAT_100%NDR: ['20/63/200', '10/66/169']
+
LAT_10%NDR:(10/20/46),(10/16/87)
−
LAT_50%NDR: ['10/26/75', '10/25/74']
+
−
LAT_10%NDR: ['10/20/46', '10/16/87']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 6132079.0625 pps (2x 3066039.53125 pps)  
+
|RATE: 6132079 pps (2x 3066039 pps) BANDWIDTH: 4.807 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.807549985 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/61/138 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/64/130 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1600400.28125 pps (2x 800200.140625 pps)  
+
|RATE: 1600400 pps (2x 800200 pps) BANDWIDTH: 19.691 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.6913250605 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/64),(20/30/54)
−
LAT_100%NDR: ['20/32/77', '20/32/74']
+
LAT_10%NDR:(20/26/88),(10/26/72)
−
LAT_50%NDR: ['20/27/64', '20/30/54']
+
−
LAT_10%NDR: ['20/26/88', '10/26/72']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/227/242 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/225/267 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/97),(50/64/116)
−
LAT_100%NDR: ['50/196/218', '60/194/268']
+
LAT_10%NDR:(50/57/93),(50/61/132)
−
LAT_50%NDR: ['50/62/97', '50/64/116']
+
−
LAT_10%NDR: ['50/57/93', '50/61/132']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/182/261 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/205/227 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 10482270.375 pps (2x 5241135.1875 pps)  
+
|RATE: 10482270 pps (2x 5241135 pps) BANDWIDTH: 8.218 Gbps (untagged)
−
FINAL_BANDWIDTH: 8.218099974 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/59),(10/24/88)
−
LAT_100%NDR: ['10/41/132', '10/986/1021']
+
LAT_10%NDR:(10/10/47),(10/8/46)
−
LAT_50%NDR: ['10/24/59', '10/24/88']
+
−
LAT_10%NDR: ['10/10/47', '10/8/46']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 10877742.3125 pps (2x 5438871.15625 pps)  
+
|RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 8.528149973 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/39/86 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/974/1026 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/63),(20/26/115)
−
LAT_100%NDR: ['20/115/131', '20/214/237']
+
LAT_10%NDR:(20/25/95),(10/25/115)
−
LAT_50%NDR: ['20/25/63', '20/26/115']
+
−
LAT_10%NDR: ['20/25/95', '10/25/115']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/182/199 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/152/174 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/190),(50/65/138)
−
LAT_100%NDR: ['50/217/265', '50/114/139']
+
LAT_10%NDR:(50/57/123),(50/58/105)
−
LAT_50%NDR: ['50/63/190', '50/65/138']
+
−
LAT_10%NDR: ['50/57/123', '50/58/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/97/179 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/207/276 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/19/74),(10/19/74)
−
LAT_100%NDR: ['20/40/74', '10/47/104']
+
LAT_10%NDR:(10/18/38),(10/17/67)
−
LAT_50%NDR: ['10/19/74', '10/19/74']
+
−
LAT_10%NDR: ['10/18/38', '10/17/67']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/39/104 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/42/72 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/86),(20/26/80)
−
LAT_100%NDR: ['20/44/155', '20/68/174']
+
LAT_10%NDR:(20/25/75),(10/26/92)
−
LAT_50%NDR: ['20/25/86', '20/26/80']
+
−
LAT_10%NDR: ['20/25/75', '10/26/92']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/110/143 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/85/142 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/186),(50/64/121)
−
LAT_100%NDR: ['50/158/217', '50/95/161']
+
LAT_10%NDR:(50/57/85),(50/58/111)
−
LAT_50%NDR: ['50/63/186', '50/64/121']
+
−
LAT_10%NDR: ['50/57/85', '50/58/111']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/117/158 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/132/152 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 Fib 200k Intel-X520-DA2=====
 
=====Long IPv6 Fib 200k Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,616: Line 2,980:
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)  
+
|RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/12/237),(10/12/230)
−
LAT_100%NDR: ['10/1540/1714', '10/1540/1740']
+
LAT_10%NDR:(10/20/69),(10/19/58)
−
LAT_50%NDR: ['10/12/237', '10/12/230']
+
−
LAT_10%NDR: ['10/20/69', '10/19/58']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)  
+
|RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/61/349 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/63/370 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/190),(10/28/190)
−
LAT_100%NDR: ['20/364/381', '20/386/439']
+
LAT_10%NDR:(10/25/117),(10/24/132)
−
LAT_50%NDR: ['20/28/190', '10/28/190']
+
−
LAT_10%NDR: ['10/25/117', '10/24/132']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/400/457 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/455/474 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/201),(50/64/181)
−
LAT_100%NDR: ['50/144/374', '50/105/243']
+
LAT_10%NDR:(50/57/145),(50/57/118)
−
LAT_50%NDR: ['50/64/201', '50/64/181']
+
−
LAT_10%NDR: ['50/57/145', '50/57/118']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/274/310 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/221/272 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 13646045.875 pps (2x 6823022.9375 pps)  
+
|RATE: 13646045 pps (2x 6823022 pps) BANDWIDTH: 10.698 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.698499966 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/127),(10/26/114)
−
LAT_100%NDR: ['10/40/241', '10/778/816']
+
LAT_10%NDR:(10/19/110),(10/19/71)
−
LAT_50%NDR: ['10/23/127', '10/26/114']
+
−
LAT_10%NDR: ['10/19/110', '10/19/71']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 14041517.8125 pps (2x 7020758.90625 pps)  
+
|RATE: 14041517 pps (2x 7020758 pps) BANDWIDTH: 11.008 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.008549965 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/42/230 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/60/337 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/181),(10/26/89)
−
LAT_100%NDR: ['20/320/360', '20/98/133']
+
LAT_10%NDR:(10/25/75),(10/24/78)
−
LAT_50%NDR: ['10/26/181', '10/26/89']
+
−
LAT_10%NDR: ['10/25/75', '10/24/78']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/251/288 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/197/261 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/179),(50/65/220)
−
LAT_100%NDR: ['50/240/267', '60/188/240']
+
LAT_10%NDR:(50/57/69),(50/60/188)
−
LAT_50%NDR: ['50/63/179', '50/65/220']
+
−
LAT_10%NDR: ['50/57/69', '50/60/188']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/282/308 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/115/165 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/10/141),(10/9/86)
−
LAT_100%NDR: ['10/33/82', '10/31/116']
+
LAT_10%NDR:(10/18/62),(10/15/42)
−
LAT_50%NDR: ['10/10/141', '10/9/86']
+
−
LAT_10%NDR: ['10/18/62', '10/15/42']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 21555484.625 pps (2x 10777742.3125 pps)  
+
|RATE: 21555484 pps (2x 10777742 pps) BANDWIDTH: 16.899 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.899499946 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/776/816 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/777/959 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/81),(20/26/147)
−
LAT_100%NDR: ['20/156/245', '20/142/201']
+
LAT_10%NDR:(10/25/106),(10/26/130)
−
LAT_50%NDR: ['10/25/81', '20/26/147']
+
−
LAT_10%NDR: ['10/25/106', '10/26/130']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/107/197 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/141/199 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/119),(50/63/96)
−
LAT_100%NDR: ['50/143/208', '60/149/206']
+
LAT_10%NDR:(50/59/88),(50/60/77)
−
LAT_50%NDR: ['50/63/119', '50/63/96']
+
−
LAT_10%NDR: ['50/59/88', '50/60/77']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/86/216 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/83/232 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 Fib 20k Intel-X520-DA2=====
 
=====Long IPv6 Fib 20k Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,798: Line 3,108:
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)  
+
|RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/609),(10/24/592)
−
LAT_100%NDR: ['10/63/187', '10/65/172']
+
LAT_10%NDR:(10/20/419),(10/17/399)
−
LAT_50%NDR: ['10/24/609', '10/24/592']
+
−
LAT_10%NDR: ['10/20/419', '10/17/399']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)  
+
|RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/62/222 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/64/209 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/109),(10/27/112)
−
LAT_100%NDR: ['20/223/284', '20/227/272']
+
LAT_10%NDR:(10/26/105),(10/25/83)
−
LAT_50%NDR: ['10/27/109', '10/27/112']
+
−
LAT_10%NDR: ['10/26/105', '10/25/83']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/200/226 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/214/248 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/506),(50/63/481)
−
LAT_100%NDR: ['50/181/217', '50/162/202']
+
LAT_10%NDR:(50/61/87),(50/61/135)
−
LAT_50%NDR: ['50/64/506', '50/63/481']
+
−
LAT_10%NDR: ['50/61/87', '50/61/135']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/205/231 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/183/241 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 14436989.75 pps (2x 7218494.875 pps)  
+
|RATE: 14436989 pps (2x 7218494 pps) BANDWIDTH: 11.318 Gbps (untagged)
−
FINAL_BANDWIDTH: 11.318599964 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/112),(10/24/127)
−
LAT_100%NDR: ['10/46/130', '10/757/847']
+
LAT_10%NDR:(10/20/45),(10/18/68)
−
LAT_50%NDR: ['10/23/112', '10/24/127']
+
−
LAT_10%NDR: ['10/20/45', '10/18/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 14436989.75 pps (2x 7218494.875 pps)  
+
|RATE: 14436989 pps (2x 7218494 pps) BANDWIDTH: 11.318 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.318599964 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/48/104 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1437/1514 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/126),(10/27/95)
−
LAT_100%NDR: ['20/196/227', '20/127/172']
+
LAT_10%NDR:(10/26/618),(10/26/683)
−
LAT_50%NDR: ['20/27/126', '10/27/95']
+
−
LAT_10%NDR: ['10/26/618', '10/26/683']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/210/254 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/117/140 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/397),(50/65/479)
−
LAT_100%NDR: ['50/237/274', '50/114/143']
+
LAT_10%NDR:(50/28/143),(50/28/100)
−
LAT_50%NDR: ['50/63/397', '50/65/479']
+
−
LAT_10%NDR: ['50/28/143', '50/28/100']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/160/231 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/112/197 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/55),(10/18/140)
−
LAT_100%NDR: ['10/29/73', '10/28/129']
+
LAT_10%NDR:(10/18/57),(10/16/122)
−
LAT_50%NDR: ['10/18/55', '10/18/140']
+
−
LAT_10%NDR: ['10/18/57', '10/16/122']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/27/45 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/27/123 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/87),(10/27/70)
−
LAT_100%NDR: ['20/114/165', '20/107/132']
+
LAT_10%NDR:(20/25/93),(10/26/50)
−
LAT_50%NDR: ['20/26/87', '10/27/70']
+
−
LAT_10%NDR: ['20/25/93', '10/26/50']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/46/139 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/66/149 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/60/110),(50/65/121)
−
LAT_100%NDR: ['50/118/149', '60/110/163']
+
LAT_10%NDR:(50/57/106),(50/60/83)
−
LAT_50%NDR: ['50/60/110', '50/65/121']
+
−
LAT_10%NDR: ['50/57/106', '50/60/83']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/90/134 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/115/181 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 Fib 2M Intel-X520-DA2=====
 
=====Long IPv6 Fib 2M Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 3,980: Line 3,236:
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)  
+
|RATE: 5341135 pps (2x 2670567 pps) BANDWIDTH: 4.187 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/592),(10/27/683)
−
LAT_100%NDR: ['10/222/823', '10/231/884']
+
LAT_10%NDR:(10/19/45),(10/18/54)
−
LAT_50%NDR: ['10/26/592', '10/27/683']
+
−
LAT_10%NDR: ['10/19/45', '10/18/54']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)  
+
|RATE: 5341135 pps (2x 2670567 pps) BANDWIDTH: 4.187 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/229/863 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/240/832 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/30/669),(10/29/667)
−
LAT_100%NDR: ['20/485/494', '20/302/351']
+
LAT_10%NDR:(10/26/164),(10/25/139)
−
LAT_50%NDR: ['20/30/669', '10/29/667']
+
−
LAT_10%NDR: ['10/26/164', '10/25/139']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/314/326 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/517/538 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/194),(50/64/257)
−
LAT_100%NDR: ['50/269/313', '60/308/375']
+
LAT_10%NDR:(50/57/107),(50/60/101)
−
LAT_50%NDR: ['50/63/194', '50/64/257']
+
−
LAT_10%NDR: ['50/57/107', '50/60/101']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/323/347 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/267/293 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 10877742.3125 pps (2x 5438871.15625 pps)  
+
|RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged)
−
FINAL_BANDWIDTH: 8.528149973 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/660),(10/27/643)
−
LAT_100%NDR: ['10/51/187', '10/89/350']
+
LAT_10%NDR:(10/20/162),(10/18/74)
−
LAT_50%NDR: ['10/28/660', '10/27/643']
+
−
LAT_10%NDR: ['10/20/162', '10/18/74']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 10877742.3125 pps (2x 5438871.15625 pps)  
+
|RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 8.528149973 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/57/230 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/109/477 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/180),(10/27/80)
−
LAT_100%NDR: ['20/390/998', '20/182/785']
+
LAT_10%NDR:(10/26/159),(10/24/74)
−
LAT_50%NDR: ['20/27/180', '10/27/80']
+
−
LAT_10%NDR: ['10/26/159', '10/24/74']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/377/385 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/115/138 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/240),(50/63/659)
−
LAT_100%NDR: ['50/369/427', '50/84/114']
+
LAT_10%NDR:(50/57/102),(50/60/160)
−
LAT_50%NDR: ['50/63/240', '50/63/659']
+
−
LAT_10%NDR: ['50/57/102', '50/60/160']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/250/267 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/253/325 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 20764540.75 pps (2x 10382270.375 pps)  
+
|RATE: 20764540 pps (2x 10382270 pps) BANDWIDTH: 16.279 Gbps (untagged)
−
FINAL_BANDWIDTH: 16.279399948 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/21/48),(10/21/45)
−
LAT_100%NDR: ['10/191/830', '10/838/1510']
+
LAT_10%NDR:(10/18/70),(2/17/49)
−
LAT_50%NDR: ['10/21/48', '10/21/45']
+
−
LAT_10%NDR: ['10/18/70', '2/17/49']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 20764540.75 pps (2x 10382270.375 pps)  
+
|RATE: 20764540 pps (2x 10382270 pps) BANDWIDTH: 16.279 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.279399948 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/120/305 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/659/1074 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/59),(10/26/200)
−
LAT_100%NDR: ['20/145/154', '20/105/159']
+
LAT_10%NDR:(10/25/50),(10/25/77)
−
LAT_50%NDR: ['20/26/59', '10/26/200']
+
−
LAT_10%NDR: ['10/25/50', '10/25/77']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/113/158 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/168/191 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/101),(50/66/156)
−
LAT_100%NDR: ['50/116/625', '60/182/595']
+
LAT_10%NDR:(50/60/78),(50/61/110)
−
LAT_50%NDR: ['50/65/101', '50/66/156']
+
−
LAT_10%NDR: ['50/60/78', '50/61/110']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/134/165 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/138/197 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 iAcl Intel-X520-DA2=====
 
=====Long IPv6 iAcl Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 iAcl whitelist test cases'''
+
*'''RFC2544: Pkt throughput IPv6 iAcl whitelist test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 4,162: Line 3,364:
 
|TC01: 78B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)  
+
|RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/71),(10/25/81)
−
LAT_100%NDR: ['10/3113/3196', '10/1718/1799']
+
LAT_10%NDR:(10/20/558),(10/17/537)
−
LAT_50%NDR: ['10/26/71', '10/25/81']
+
−
LAT_10%NDR: ['10/20/558', '10/17/537']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)  
+
|RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/2386/3187 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 40/2407/2880 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/97),(20/28/95)
−
LAT_100%NDR: ['20/234/242', '20/236/252']
+
LAT_10%NDR:(20/25/101),(10/24/128)
−
LAT_50%NDR: ['20/28/97', '20/28/95']
+
−
LAT_10%NDR: ['20/25/101', '10/24/128']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/245/265 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/242/269 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/129),(50/63/123)
−
LAT_100%NDR: ['50/183/240', '50/173/211']
+
LAT_10%NDR:(50/60/105),(50/60/137)
−
LAT_50%NDR: ['50/63/129', '50/63/123']
+
−
LAT_10%NDR: ['50/60/105', '50/60/137']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/205/574 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/212/641 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 11273214.25 pps (2x 5636607.125 pps)  
+
|RATE: 11273214 pps (2x 5636607 pps) BANDWIDTH: 8.838 Gbps (untagged)
−
FINAL_BANDWIDTH: 8.838199972 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/768),(10/23/750)
−
LAT_100%NDR: ['20/27/106', '20/460/990']
+
LAT_10%NDR:(10/18/72),(10/22/83)
−
LAT_50%NDR: ['10/25/768', '10/23/750']
+
−
LAT_10%NDR: ['10/18/72', '10/22/83']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 11273214.25 pps (2x 5636607.125 pps)  
+
|RATE: 11273214 pps (2x 5636607 pps) BANDWIDTH: 8.838 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 8.838199972 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/46/88 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/925/982 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/168),(10/26/95)
−
LAT_100%NDR: ['20/204/242', '20/144/159']
+
LAT_10%NDR:(10/25/69),(10/24/52)
−
LAT_50%NDR: ['20/25/168', '10/26/95']
+
−
LAT_10%NDR: ['10/25/69', '10/24/52']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/202/215 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/139/153 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/113),(50/63/137)
−
LAT_100%NDR: ['50/107/715', '60/183/794']
+
LAT_10%NDR:(50/57/100),(50/61/120)
−
LAT_50%NDR: ['50/63/113', '50/63/137']
+
−
LAT_10%NDR: ['50/57/100', '50/61/120']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/137/475 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/155/446 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 20369068.8124 pps (2x 10184534.4062 pps)  
+
|RATE: 20369068 pps (2x 10184534 pps) BANDWIDTH: 15.969 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.9693499489 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/19/39),(10/20/66)
−
LAT_100%NDR: ['10/42/722', '10/48/700']
+
LAT_10%NDR:(10/18/64),(10/17/68)
−
LAT_50%NDR: ['10/19/39', '10/20/66']
+
−
LAT_10%NDR: ['10/18/64', '10/17/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/62/353 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/624/696 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/125),(10/26/79)
−
LAT_100%NDR: ['20/139/742', '20/83/717']
+
LAT_10%NDR:(20/26/67),(10/23/68)
−
LAT_50%NDR: ['20/26/125', '10/26/79']
+
−
LAT_10%NDR: ['20/26/67', '10/23/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/101/749 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/150/836 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/130),(50/64/125)
−
LAT_100%NDR: ['50/131/192', '60/107/182']
+
LAT_10%NDR:(50/61/91),(50/60/74)
−
LAT_50%NDR: ['50/63/130', '50/64/125']
+
−
LAT_10%NDR: ['50/61/91', '50/60/74']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing and whitelist filters config with  4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/134/189 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/131/168 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long IPv6 Intel-X520-DA2=====
 
=====Long IPv6 Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
+
*'''RFC2544: Pkt throughput IPv6 routing test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv6 for IPv6 routing.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 4,344: Line 3,492:
 
|TC01: 78B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC01: 78B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 2968303.5625 pps (2x 1484151.78125 pps)  
+
|RATE: 2968303 pps (2x 1484151 pps) BANDWIDTH: 2.327 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.327149993 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/19/37),(10/21/70)
−
LAT_100%NDR: ['10/22/533', '10/23/516']
+
LAT_10%NDR:(10/19/557),(10/17/535)
−
LAT_50%NDR: ['10/19/37', '10/21/70']
+
−
LAT_10%NDR: ['10/19/557', '10/17/535']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 78B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC02: 78B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7713966.8125 pps (2x 3856983.40625 pps)  
+
|RATE: 7713966 pps (2x 3856983 pps) BANDWIDTH: 6.047 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.047749981 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/52/163 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/54/144 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/585),(10/28/657)
−
LAT_100%NDR: ['20/249/260', '20/243/281']
+
LAT_10%NDR:(10/25/84),(10/25/61)
−
LAT_50%NDR: ['20/27/585', '10/28/657']
+
−
LAT_10%NDR: ['10/25/84', '10/25/61']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/203/230 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/186/211 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/142),(50/64/144)
−
LAT_100%NDR: ['50/186/708', '50/173/780']
+
LAT_10%NDR:(50/60/113),(50/57/106)
−
LAT_50%NDR: ['50/63/142', '50/64/144']
+
−
LAT_10%NDR: ['50/60/113', '50/57/106']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv6 - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/265/650 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/208/527 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 78B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC07: 78B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 15227933.625 pps (2x 7613966.8125 pps)  
+
|RATE: 15227933 pps (2x 7613966 pps) BANDWIDTH: 11.938 Gbps (untagged)
−
FINAL_BANDWIDTH: 11.938699962 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/592),(10/24/562)
−
LAT_100%NDR: ['10/37/94', '20/695/780']
+
LAT_10%NDR:(10/18/68),(10/20/53)
−
LAT_50%NDR: ['10/23/592', '10/24/562']
+
−
LAT_10%NDR: ['10/18/68', '10/20/53']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 78B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC08: 78B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 15623405.5625 pps (2x 7811702.78125 pps)  
+
|RATE: 15623405 pps (2x 7811702 pps) BANDWIDTH: 12.248 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.248749961 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/38/107 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/56/102 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/677),(10/27/654)
−
LAT_100%NDR: ['20/100/124', '20/211/229']
+
LAT_10%NDR:(10/25/45),(10/26/118)
−
LAT_50%NDR: ['20/26/677', '10/27/654']
+
−
LAT_10%NDR: ['10/25/45', '10/26/118']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/187/211 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/126/181 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/31/173),(50/32/143)
−
LAT_100%NDR: ['50/213/780', '60/107/644']
+
LAT_10%NDR:(50/57/117),(50/61/108)
−
LAT_50%NDR: ['50/31/173', '50/32/143']
+
−
LAT_10%NDR: ['50/57/117', '50/61/108']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/125/196 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/224/255 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 78B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC13: 78B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/17/75),(10/17/121)
−
LAT_100%NDR: ['10/27/595', '10/28/585']
+
LAT_10%NDR:(10/18/32),(10/17/69)
−
LAT_50%NDR: ['10/17/75', '10/17/121']
+
−
LAT_10%NDR: ['10/18/32', '10/17/69']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 78B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC14: 78B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)  
+
|RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/26/79 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/27/82 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/25/130),(10/26/94)
−
LAT_100%NDR: ['20/133/185', '20/131/177']
+
LAT_10%NDR:(20/25/49),(10/23/75)
−
LAT_50%NDR: ['20/25/130', '10/26/94']
+
−
LAT_10%NDR: ['20/25/49', '10/23/75']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/77/657 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/141/747 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/66/164),(50/66/105)
−
LAT_100%NDR: ['60/117/181', '50/112/177']
+
LAT_10%NDR:(50/61/154),(50/61/105)
−
LAT_50%NDR: ['50/66/164', '50/66/105']
+
−
LAT_10%NDR: ['50/61/154', '50/61/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/151/186 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/118/174 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Lisp Intel-X520-DA2=====
 
=====Long Lisp Intel-X520-DA2=====
  
−
*'''RFC6830: Pkt throughput Lisp test cases'''
+
*'''RFC6830: Pkt throughput Lisp test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 (IPv6) routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with IPv4 (IPv6) routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
 
*'''[Ref] Applicable standard specifications:''' RFC6830.
 
*'''[Ref] Applicable standard specifications:''' RFC6830.
 
{| class="wikitable"
 
{| class="wikitable"
Line 4,526: Line 3,620:
 
|TC01: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 4414673.75 pps (2x 2207336.875 pps)  
+
|RATE: 4414673 pps (2x 2207336 pps) BANDWIDTH: 2.966 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.96666076 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/36/738),(10/39/698)
−
LAT_100%NDR: ['50/3018/3309', '50/4007/4850']
+
LAT_10%NDR:(10/21/63),(10/21/56)
−
LAT_50%NDR: ['10/36/738', '10/39/698']
+
−
LAT_10%NDR: ['10/21/63', '10/21/56']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 4625407.4375 pps (2x 2312703.71875 pps)  
+
|RATE: 4625407 pps (2x 2312703 pps) BANDWIDTH: 3.108 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.108273798 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/3468/4836 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/3807/4821 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC03: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/32/786),(20/32/781)
−
LAT_100%NDR: ['20/1368/1421', '20/1368/1387']
+
LAT_10%NDR:(20/26/103),(20/26/76)
−
LAT_50%NDR: ['20/32/786', '20/32/781']
+
−
LAT_10%NDR: ['20/26/103', '20/26/76']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC04: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1367/1399 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1365/1416 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/66/809),(50/67/777)
−
LAT_100%NDR: ['50/72/118', '60/74/121']
+
LAT_10%NDR:(50/58/109),(50/62/82)
−
LAT_50%NDR: ['50/66/809', '50/67/777']
+
−
LAT_10%NDR: ['50/58/109', '50/62/82']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/1617/1723 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/1618/1748 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC07: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8207880.125 pps (2x 4103940.0625 pps)  
+
|RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.515695444 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/30/99),(10/31/168)
−
LAT_100%NDR: ['10/103/779', '30/1071/1765']
+
LAT_10%NDR:(10/20/64),(10/20/51)
−
LAT_50%NDR: ['10/30/99', '10/31/168']
+
−
LAT_10%NDR: ['10/20/64', '10/20/51']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC08: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8207880.125 pps (2x 4103940.0625 pps)  
+
|RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.515695444 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/106/177 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1072/1153 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC09: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/29/781),(20/27/734)
−
LAT_100%NDR: ['20/1361/1460', '20/1362/1415']
+
LAT_10%NDR:(20/26/86),(20/24/76)
−
LAT_50%NDR: ['20/29/781', '20/27/734']
+
−
LAT_10%NDR: ['20/26/86', '20/24/76']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC10: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1363/1466 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1364/1391 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC11: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/67/676),(50/67/650)
−
LAT_100%NDR: ['60/72/115', '50/73/115']
+
LAT_10%NDR:(50/58/69),(50/61/105)
−
LAT_50%NDR: ['50/67/676', '50/67/650']
+
−
LAT_10%NDR: ['50/58/69', '50/61/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC12: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/1616/1977 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/1617/1945 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC13: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7997146.4375 pps (2x 3998573.21875 pps)  
+
|RATE: 7997146 pps (2x 3998573 pps) BANDWIDTH: 5.374 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.374082406 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/21/134),(10/22/98)
−
LAT_100%NDR: ['10/57/156', '10/90/197']
+
LAT_10%NDR:(10/10/79),(10/10/56)
−
LAT_50%NDR: ['10/21/134', '10/22/98']
+
−
LAT_10%NDR: ['10/10/79', '10/10/56']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC14: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8207880.125 pps (2x 4103940.0625 pps)  
+
|RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.515695444 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/108/797 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1073/1788 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC15: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/44),(20/28/76)
−
LAT_100%NDR: ['20/2545/3311', '20/2543/3291']
+
LAT_10%NDR:(20/26/86),(20/26/71)
−
LAT_50%NDR: ['20/28/44', '20/28/76']
+
−
LAT_10%NDR: ['20/26/86', '20/26/71']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC16: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/2542/2585 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/2538/2573 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC17: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/66/120),(50/66/113)
−
LAT_100%NDR: ['50/35/741', '60/36/705']
+
LAT_10%NDR:(50/59/73),(50/61/105)
−
LAT_50%NDR: ['50/66/120', '50/66/113']
+
−
LAT_10%NDR: ['50/59/73', '50/61/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC18: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/2844/2946 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/2843/2941 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC19: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 3488502.125 pps (2x 1744251.0625 pps)  
+
|RATE: 3488502 pps (2x 1744251 pps) BANDWIDTH: 2.734 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.734985666 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/33/130),(10/35/114)
−
LAT_100%NDR: ['10/64/776', '10/65/757']
+
LAT_10%NDR:(10/10/83),(10/12/84)
−
LAT_50%NDR: ['10/33/130', '10/35/114']
+
−
LAT_10%NDR: ['10/10/83', '10/12/84']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC20: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 3853891.25 pps (2x 1926945.625 pps)  
+
|RATE: 3853891 pps (2x 1926945 pps) BANDWIDTH: 3.021 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.02145074 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/2863/3899 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/4681/4816 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC21: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC21: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.02264128 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/37/95),(20/37/111)
−
LAT_100%NDR: ['20/1369/1448', '20/1369/1468']
+
LAT_10%NDR:(20/28/744),(20/29/811)
−
LAT_50%NDR: ['20/37/95', '20/37/111']
+
−
LAT_10%NDR: ['20/28/744', '20/29/811']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC22: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC22: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.32563872 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1372/2060 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1371/2041 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC23: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC23: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/67/121),(50/68/134)
−
LAT_100%NDR: ['50/76/188', '50/77/177']
+
LAT_10%NDR:(50/61/97),(50/63/86)
−
LAT_50%NDR: ['50/67/121', '50/68/134']
+
−
LAT_10%NDR: ['50/61/97', '50/63/86']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC24: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC24: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/76/152 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/78/159 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC25: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC25: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7873171.625 pps (2x 3936585.8125 pps)  
+
|RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.172566554 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/29/113),(10/30/169)
−
LAT_100%NDR: ['40/72/214', '40/96/214']
+
LAT_10%NDR:(10/20/124),(10/20/80)
−
LAT_50%NDR: ['10/29/113', '10/30/169']
+
−
LAT_10%NDR: ['10/20/124', '10/20/80']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC26: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC26: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7873171.625 pps (2x 3936585.8125 pps)  
+
|RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.172566554 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/90/224 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/325/464 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC27: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC27: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.02264128 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/29/77),(20/29/77)
−
LAT_100%NDR: ['20/1361/1380', '20/1360/1437']
+
LAT_10%NDR:(20/27/42),(20/26/56)
−
LAT_50%NDR: ['20/29/77', '20/29/77']
+
−
LAT_10%NDR: ['20/27/42', '20/26/56']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC28: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC28: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.32563872 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1361/1380 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1361/1382 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC29: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC29: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/133),(50/67/97)
−
LAT_100%NDR: ['60/73/114', '60/75/88']
+
LAT_10%NDR:(50/64/724),(50/64/697)
−
LAT_50%NDR: ['50/64/133', '50/67/97']
+
−
LAT_10%NDR: ['50/64/724', '50/64/697']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC30: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC30: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/72/155 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/75/109 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC31: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC31: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7873171.625 pps (2x 3936585.8125 pps)  
+
|RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.172566554 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/26/104),(10/25/137)
−
LAT_100%NDR: ['10/50/121', '10/46/76']
+
LAT_10%NDR:(10/21/747),(10/21/707)
−
LAT_50%NDR: ['10/26/104', '10/25/137']
+
−
LAT_10%NDR: ['10/21/747', '10/21/707']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC32: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC32: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8238560.75 pps (2x 4119280.375 pps)  
+
|RATE: 8238560 pps (2x 4119280 pps) BANDWIDTH: 6.459 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.459031628 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/945/1656 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/954/1635 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC33: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC33: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)  
+
|RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.02264128 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/723),(20/28/708)
−
LAT_100%NDR: ['20/2540/2595', '20/2541/2640']
+
LAT_10%NDR:(20/27/46),(20/27/43)
−
LAT_50%NDR: ['20/28/723', '20/28/708']
+
−
LAT_10%NDR: ['20/27/46', '20/27/43']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC34: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC34: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)  
+
|RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.32563872 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1925/2593 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1904/2575 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC35: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC35: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/66/774),(50/67/841)
−
LAT_100%NDR: ['50/74/153', '60/75/104']
+
LAT_10%NDR:(50/63/81),(50/60/108)
−
LAT_50%NDR: ['50/66/774', '50/67/841']
+
−
LAT_10%NDR: ['50/63/81', '50/60/108']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC36: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC36: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 260233.75 pps (2x 130116.875 pps)  
+
|RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 18.7784674 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/73/520 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/74/607 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC37: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC37: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 4006439.0 pps (2x 2003219.5 pps)  
+
|RATE: 4006439 pps (2x 2003219 pps) BANDWIDTH: 2.692 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.692327008 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/31/743),(10/31/726)
−
LAT_100%NDR: ['10/198/302', '20/201/354']
+
LAT_10%NDR:(10/22/87),(10/22/69)
−
LAT_50%NDR: ['10/31/743', '10/31/726']
+
−
LAT_10%NDR: ['10/22/87', '10/22/69']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC38: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC38: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 4006439.0 pps (2x 2003219.5 pps)  
+
|RATE: 4006439 pps (2x 2003219 pps) BANDWIDTH: 2.692 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 2.692327008 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/206/330 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/212/334 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC39: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC39: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/39/79),(20/39/75)
−
LAT_100%NDR: ['20/52/220', '20/53/223']
+
LAT_10%NDR:(20/26/42),(20/29/84)
−
LAT_50%NDR: ['20/39/79', '20/39/75']
+
−
LAT_10%NDR: ['20/26/42', '20/29/84']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC40: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC40: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/58/154 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/56/142 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC41: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC41: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 259088.125 pps (2x 129544.0625 pps)  
+
|RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.6957991 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/68/177),(50/66/154)
−
LAT_100%NDR: ['50/76/697', '50/77/663']
+
LAT_10%NDR:(50/60/131),(50/63/117)
−
LAT_50%NDR: ['50/68/177', '50/66/154']
+
−
LAT_10%NDR: ['50/60/131', '50/63/117']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC42: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|TC42: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/1619/1897 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/1618/1868 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC43: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC43: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7812878.0 pps (2x 3906439.0 pps)  
+
|RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.250254016 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/37/722),(10/38/820)
−
LAT_100%NDR: ['20/1117/1179', '20/1140/1193']
+
LAT_10%NDR:(10/20/42),(10/20/68)
−
LAT_50%NDR: ['10/37/722', '10/38/820']
+
−
LAT_10%NDR: ['10/20/42', '10/20/68']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC44: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC44: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7812878.0 pps (2x 3906439.0 pps)  
+
|RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.250254016 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/1137/1238 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1155/1227 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC45: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC45: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/29/70),(20/29/57)
−
LAT_100%NDR: ['20/35/107', '20/36/57']
+
LAT_10%NDR:(20/27/749),(20/25/708)
−
LAT_50%NDR: ['20/29/70', '20/29/57']
+
−
LAT_10%NDR: ['20/27/749', '20/25/708']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC46: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC46: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/40/759 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/38/735 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC47: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC47: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 259088.125 pps (2x 129544.0625 pps)  
+
|RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.6957991 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/82),(50/67/130)
−
LAT_100%NDR: ['50/72/177', '50/73/167']
+
LAT_10%NDR:(50/60/112),(50/59/105)
−
LAT_50%NDR: ['50/65/82', '50/67/130']
+
−
LAT_10%NDR: ['50/60/112', '50/59/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC48: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|TC48: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/1614/1689 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/1616/1695 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC49: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC49: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7812878.0 pps (2x 3906439.0 pps)  
+
|RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.250254016 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/70),(10/25/73)
−
LAT_100%NDR: ['10/1111/1202', '10/1112/1161']
+
LAT_10%NDR:(10/20/47),(10/20/67)
−
LAT_50%NDR: ['10/24/70', '10/25/73']
+
−
LAT_10%NDR: ['10/20/47', '10/20/67']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC50: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC50: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7812878.0 pps (2x 3906439.0 pps)  
+
|RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.250254016 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1102/1155 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1116/1195 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC51: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC51: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/95),(20/27/75)
−
LAT_100%NDR: ['20/38/93', '20/39/81']
+
LAT_10%NDR:(20/26/71),(20/24/105)
−
LAT_50%NDR: ['20/27/95', '20/27/75']
+
−
LAT_10%NDR: ['20/26/71', '20/24/105']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC52: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC52: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)  
+
|RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/41/81 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/41/70 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC53: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC53: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 259088.125 pps (2x 129544.0625 pps)  
+
|RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)
−
FINAL_BANDWIDTH: 18.6957991 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/114),(50/65/139)
−
LAT_100%NDR: ['50/73/154', '50/74/142']
+
LAT_10%NDR:(50/59/782),(50/63/750)
−
LAT_50%NDR: ['50/65/114', '50/65/139']
+
−
LAT_10%NDR: ['50/59/782', '50/63/750']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC54: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|TC54: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/2831/2934 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/2834/2931 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC55: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC55: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 4166395.15624 pps (2x 2083197.57812 pps)  
+
|RATE: 4166395 pps (2x 2083197 pps) BANDWIDTH: 3.266 Gbps (untagged)
−
FINAL_BANDWIDTH: 3.26645380249 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/32/85),(10/35/118)
−
LAT_100%NDR: ['20/106/229', '20/109/211']
+
LAT_10%NDR:(10/21/663),(10/20/740)
−
LAT_50%NDR: ['10/32/85', '10/35/118']
+
−
LAT_10%NDR: ['10/21/663', '10/20/740']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC56: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC56: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 4166395.15624 pps (2x 2083197.57812 pps)  
+
|RATE: 4166395 pps (2x 2083197 pps) BANDWIDTH: 3.266 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.26645380249 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/107/802 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/108/782 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC57: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC57: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/34/156),(20/34/167)
−
LAT_100%NDR: ['20/47/177', '20/47/176']
+
LAT_10%NDR:(20/26/89),(20/26/73)
−
LAT_50%NDR: ['20/34/156', '20/34/167']
+
−
LAT_10%NDR: ['20/26/89', '20/26/73']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC58: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC58: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/52/178 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/51/187 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC59: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC59: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/32/124),(50/33/162)
−
LAT_100%NDR: ['60/78/190', '60/78/188']
+
LAT_10%NDR:(50/59/580),(50/62/545)
−
LAT_50%NDR: ['50/32/124', '50/33/162']
+
−
LAT_10%NDR: ['50/59/580', '50/62/545']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC60: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|TC60: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/80/180 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/80/186 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC61: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC61: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)  
+
|RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/56),(10/30/58)
−
LAT_100%NDR: ['10/1016/1072', '10/1039/1088']
+
LAT_10%NDR:(10/22/85),(10/22/55)
−
LAT_50%NDR: ['10/28/56', '10/30/58']
+
−
LAT_10%NDR: ['10/22/85', '10/22/55']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC62: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC62: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)  
+
|RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1012/1113 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1042/1105 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC63: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC63: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/152),(20/28/114)
−
LAT_100%NDR: ['20/34/690', '20/34/768']
+
LAT_10%NDR:(20/26/90),(20/24/49)
−
LAT_50%NDR: ['20/27/152', '20/28/114']
+
−
LAT_10%NDR: ['20/26/90', '20/24/49']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC64: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC64: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/35/134 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/35/163 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC65: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC65: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/185),(50/66/138)
−
LAT_100%NDR: ['60/37/195', '60/38/160']
+
LAT_10%NDR:(50/62/544),(50/58/479)
−
LAT_50%NDR: ['50/65/185', '50/66/138']
+
−
LAT_10%NDR: ['50/62/544', '50/58/479']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC66: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|TC66: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/76/195 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/78/165 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC67: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC67: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 8397216.65624 pps (2x 4198608.32812 pps)  
+
|RATE: 8397216 pps (2x 4198608 pps) BANDWIDTH: 6.583 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.58341785849 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/75),(10/25/57)
−
LAT_100%NDR: ['10/46/142', '20/52/173']
+
LAT_10%NDR:(10/20/691),(10/21/666)
−
LAT_50%NDR: ['10/20/75', '10/25/57']
+
−
LAT_10%NDR: ['10/20/691', '10/21/666']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC68: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC68: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)  
+
|RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/997/1653 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1032/1649 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC69: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC69: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/112),(20/29/98)
−
LAT_100%NDR: ['20/37/136', '20/37/126']
+
LAT_10%NDR:(20/26/78),(20/27/76)
−
LAT_50%NDR: ['20/27/112', '20/29/98']
+
−
LAT_10%NDR: ['20/26/78', '20/27/76']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC70: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC70: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)  
+
|RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/33/181 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/33/131 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC71: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC71: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/136),(50/65/174)
−
LAT_100%NDR: ['50/77/156', '60/78/157']
+
LAT_10%NDR:(50/59/135),(50/62/122)
−
LAT_50%NDR: ['50/65/136', '50/65/174']
+
−
LAT_10%NDR: ['50/59/135', '50/62/122']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC72: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|TC72: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist  filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275694.0 pps (2x 137847.0 pps)  
+
|RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/75/206 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/76/160 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Dot1ad Intel-X520-DA2=====
 
=====Long Xconnect Dot1ad Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2XC with 802.1ad test cases'''
+
*'''RFC2544: Pkt throughput L2XC with 802.1ad test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 xconnect. 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B vlan tag (id=100) and outer 4B vlan tag (id=200).  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 xconnect. 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B vlan tag (id=100) and outer 4B vlan tag (id=200).
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 5,221: Line 4,099:
 
|TC01: 64B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7364945.375 pps (2x 3682472.6875 pps)  
+
|RATE: 7364945 pps (2x 3682472 pps) BANDWIDTH: 4.949 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.949243292 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/612),(10/28/604)
−
LAT_100%NDR: ['30/1788/1861', '20/1427/1494']
+
LAT_10%NDR:(10/19/35),(10/16/81)
−
LAT_50%NDR: ['10/28/612', '10/28/604']
+
−
LAT_10%NDR: ['10/19/35', '10/16/81']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7364945.375 pps (2x 3682472.6875 pps)  
+
|RATE: 7364945 pps (2x 3682472 pps) BANDWIDTH: 4.949 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 4.949243292 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/702/1529 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/896/1886 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1514B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC03: 1514B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/143),(10/27/139)
−
LAT_100%NDR: ['20/124/174', '20/120/237']
+
LAT_10%NDR:(20/25/47),(10/23/107)
−
LAT_50%NDR: ['20/26/143', '10/27/139']
+
−
LAT_10%NDR: ['20/25/47', '10/23/107']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1514B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC04: 1514B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/129/164 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/119/234 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/162),(50/64/143)
−
LAT_100%NDR: ['50/63/225', '50/77/224']
+
LAT_10%NDR:(50/61/487),(50/61/460)
−
LAT_50%NDR: ['50/65/162', '50/64/143']
+
−
LAT_10%NDR: ['50/61/487', '50/61/460']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/154/192 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/160/254 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 14951358.125 pps (2x 7475679.0625 pps)  
+
|RATE: 14951358 pps (2x 7475679 pps) BANDWIDTH: 10.047 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.04731266 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/11/145),(10/11/76)
−
LAT_100%NDR: ['10/39/127', '10/894/959']
+
LAT_10%NDR:(10/20/86),(10/18/66)
−
LAT_50%NDR: ['10/11/145', '10/11/76']
+
−
LAT_10%NDR: ['10/20/86', '10/18/66']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 15162091.8125 pps (2x 7581045.90625 pps)  
+
|RATE: 15162091 pps (2x 7581045 pps) BANDWIDTH: 10.188 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 10.188925698 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/37/83 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/899/929 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1514B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC09: 1514B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/582),(10/26/666)
−
LAT_100%NDR: ['20/77/98', '20/156/270']
+
LAT_10%NDR:(10/25/83),(10/23/93)
−
LAT_50%NDR: ['10/25/582', '10/26/666']
+
−
LAT_10%NDR: ['10/25/83', '10/23/93']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1514B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC10: 1514B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/135/200 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/80/143 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/134),(50/65/181)
−
LAT_100%NDR: ['50/105/131', '50/167/281']
+
LAT_10%NDR:(50/60/76),(50/60/162)
−
LAT_50%NDR: ['50/65/134', '50/65/181']
+
−
LAT_10%NDR: ['50/60/76', '50/60/162']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/123/185 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/113/249 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 16005026.5625 pps (2x 8002513.28125 pps)  
+
|RATE: 16005026 pps (2x 8002513 pps) BANDWIDTH: 10.755 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.75537785 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/47),(10/17/158)
−
LAT_100%NDR: ['10/30/49', '10/42/65']
+
LAT_10%NDR:(10/18/34),(10/17/39)
−
LAT_50%NDR: ['10/18/47', '10/17/158']
+
−
LAT_10%NDR: ['10/18/34', '10/17/39']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 16426493.9375 pps (2x 8213246.96875 pps)  
+
|RATE: 16426493 pps (2x 8213246 pps) BANDWIDTH: 11.038 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.038603926 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/17/138 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/323/714 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1514B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC15: 1514B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/642),(10/27/614)
−
LAT_100%NDR: ['20/73/131', '20/108/192']
+
LAT_10%NDR:(10/25/75),(10/24/61)
−
LAT_50%NDR: ['10/25/642', '10/27/614']
+
−
LAT_10%NDR: ['10/25/75', '10/24/61']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1514B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC16: 1514B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/28/587 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/39/658 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/62/105),(50/65/127)
−
LAT_100%NDR: ['50/115/188', '60/140/169']
+
LAT_10%NDR:(50/60/134),(50/61/95)
−
LAT_50%NDR: ['50/62/105', '50/65/127']
+
−
LAT_10%NDR: ['50/60/134', '50/61/95']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 276916.0 pps (2x 138458.0 pps)  
+
|RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/113/181 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/86/206 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Dot1q Intel-X520-DA2=====
 
=====Long Xconnect Dot1q Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2XC with 802.1q test cases'''
+
*'''RFC2544: Pkt throughput L2XC with 802.1q test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 5,403: Line 4,227:
 
|TC01: 64B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 7472656.01562 pps (2x 3736328.00781 pps)  
+
|RATE: 7472656 pps (2x 3736328 pps) BANDWIDTH: 5.021 Gbps (untagged)
−
FINAL_BANDWIDTH: 5.0216248425 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/23/177),(10/22/141)
−
LAT_100%NDR: ['10/61/178', '10/64/177']
+
LAT_10%NDR:(10/19/49),(10/17/35)
−
LAT_50%NDR: ['10/23/177', '10/22/141']
+
−
LAT_10%NDR: ['10/19/49', '10/17/35']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 7472656.01562 pps (2x 3736328.00781 pps)  
+
|RATE: 7472656 pps (2x 3736328 pps) BANDWIDTH: 5.021 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 5.0216248425 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/59/126 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/62/124 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/117),(20/28/113)
−
LAT_100%NDR: ['20/114/240', '20/142/254']
+
LAT_10%NDR:(20/25/119),(10/25/84)
−
LAT_50%NDR: ['20/28/117', '20/28/113']
+
−
LAT_10%NDR: ['20/25/119', '10/25/84']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/142/254 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/130/253 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/130),(50/66/128)
−
LAT_100%NDR: ['60/161/198', '50/146/256']
+
LAT_10%NDR:(50/60/530),(50/60/602)
−
LAT_50%NDR: ['50/65/130', '50/66/128']
+
−
LAT_10%NDR: ['50/60/530', '50/60/602']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/143/189 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/149/250 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 14965695.5469 pps (2x 7482847.77344 pps)  
+
|RATE: 14965695 pps (2x 7482847 pps) BANDWIDTH: 10.056 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.0569474075 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/22/130),(10/23/87)
−
LAT_100%NDR: ['20/37/122', '10/141/284']
+
LAT_10%NDR:(10/17/57),(10/18/38)
−
LAT_50%NDR: ['10/22/130', '10/23/87']
+
−
LAT_10%NDR: ['10/17/57', '10/18/38']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 14965695.5469 pps (2x 7482847.77344 pps)  
+
|RATE: 14965695 pps (2x 7482847 pps) BANDWIDTH: 10.056 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 10.0569474075 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/42/110 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/61/105 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/136),(10/25/72)
−
LAT_100%NDR: ['20/128/718', '20/75/592']
+
LAT_10%NDR:(10/25/113),(10/23/71)
−
LAT_50%NDR: ['10/25/136', '10/25/72']
+
−
LAT_10%NDR: ['10/25/113', '10/23/71']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/122/664 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/133/752 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/89),(50/65/184)
−
LAT_100%NDR: ['60/100/131', '60/142/247']
+
LAT_10%NDR:(50/57/591),(50/61/553)
−
LAT_50%NDR: ['50/64/89', '50/65/184']
+
−
LAT_10%NDR: ['50/57/591', '50/61/553']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/150/183 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/149/224 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23340269.1406 pps (2x 11670134.5703 pps)  
+
|RATE: 23340269 pps (2x 11670134 pps) BANDWIDTH: 15.684 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.6846608625 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/18/620),(10/18/603)
−
LAT_100%NDR: ['10/27/127', '10/28/110']
+
LAT_10%NDR:(10/18/71),(10/15/53)
−
LAT_50%NDR: ['10/18/620', '10/18/603']
+
−
LAT_10%NDR: ['10/18/71', '10/15/53']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23560652.6562 pps (2x 11780326.3281 pps)  
+
|RATE: 23560652 pps (2x 11780326 pps) BANDWIDTH: 15.832 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.832758585 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/821/886 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/374/446 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/27/59),(10/26/66)
−
LAT_100%NDR: ['20/75/615', '20/72/592']
+
LAT_10%NDR:(10/26/76),(10/25/87)
−
LAT_50%NDR: ['20/27/59', '10/26/66']
+
−
LAT_10%NDR: ['10/26/76', '10/25/87']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)  
+
|RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/92/654 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/70/619 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/135),(50/64/124)
−
LAT_100%NDR: ['50/112/181', '50/87/163']
+
LAT_10%NDR:(50/60/551),(50/61/527)
−
LAT_50%NDR: ['50/64/135', '50/64/124']
+
−
LAT_10%NDR: ['50/60/551', '50/61/527']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277038.0 pps (2x 138519.0 pps)  
+
|RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/125/240 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/101/156 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Intel-X520-DA2=====
 
=====Long Xconnect Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2XC test cases'''
+
*'''RFC2544: Pkt throughput L2XC test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 5,585: Line 4,355:
 
|TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 9438095.0 pps (2x 4719047.5 pps)  
+
|RATE: 9438095 pps (2x 4719047 pps) BANDWIDTH: 6.342 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.34239984 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/85),(10/22/79)
−
LAT_100%NDR: ['10/1483/1744', '10/2723/2801']
+
LAT_10%NDR:(10/18/69),(10/19/60)
−
LAT_50%NDR: ['10/25/85', '10/22/79']
+
−
LAT_10%NDR: ['10/18/69', '10/19/60']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 9438095.0 pps (2x 4719047.5 pps)  
+
|RATE: 9438095 pps (2x 4719047 pps) BANDWIDTH: 6.342 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.34239984 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/1406/1492 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1410/1506 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/26/147),(10/27/123)
−
LAT_100%NDR: ['20/172/209', '20/153/201']
+
LAT_10%NDR:(10/26/137),(10/25/106)
−
LAT_50%NDR: ['20/26/147', '10/27/123']
+
−
LAT_10%NDR: ['10/26/137', '10/25/106']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/218/226 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/184/196 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/63/171),(50/65/172)
−
LAT_100%NDR: ['50/213/235', '50/204/224']
+
LAT_10%NDR:(50/60/103),(50/57/95)
−
LAT_50%NDR: ['50/63/171', '50/65/172']
+
−
LAT_10%NDR: ['50/60/103', '50/57/95']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/188/214 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/186/210 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 20061904.25 pps (2x 10030952.125 pps)  
+
|RATE: 20061904 pps (2x 10030952 pps) BANDWIDTH: 13.481 Gbps (untagged)
−
FINAL_BANDWIDTH: 13.481599656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/20/88),(10/19/50)
−
LAT_100%NDR: ['10/45/103', '10/681/720']
+
LAT_10%NDR:(10/18/35),(10/18/34)
−
LAT_50%NDR: ['10/20/88', '10/19/50']
+
−
LAT_10%NDR: ['10/18/35', '10/18/34']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 20292856.625 pps (2x 10146428.3125 pps)  
+
|RATE: 20292856 pps (2x 10146428 pps) BANDWIDTH: 13.636 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 13.636799652 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/45/164 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 30/682/761 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/161),(10/26/99)
−
LAT_100%NDR: ['20/270/278', '20/92/156']
+
LAT_10%NDR:(10/26/123),(10/24/94)
−
LAT_50%NDR: ['10/25/161', '10/26/99']
+
−
LAT_10%NDR: ['10/26/123', '10/24/94']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/226/243 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/132/159 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/154),(50/66/97)
−
LAT_100%NDR: ['50/186/232', '60/191/226']
+
LAT_10%NDR:(50/60/109),(50/58/178)
−
LAT_50%NDR: ['50/65/154', '50/66/97']
+
−
LAT_10%NDR: ['50/60/109', '50/58/178']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/220/281 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/162/184 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)  
+
|RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged)
−
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/16/66),(10/16/45)
−
LAT_100%NDR: ['10/25/83', '10/25/72']
+
LAT_10%NDR:(10/17/40),(10/17/29)
−
LAT_50%NDR: ['10/16/66', '10/16/45']
+
−
LAT_10%NDR: ['10/17/40', '10/17/29']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)  
+
|RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/916/989 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/471/569 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/62),(10/25/64)
−
LAT_100%NDR: ['20/49/124', '20/80/181']
+
LAT_10%NDR:(10/26/63),(10/26/113)
−
LAT_50%NDR: ['10/25/62', '10/25/64']
+
−
LAT_10%NDR: ['10/26/63', '10/26/113']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/157/166 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/84/110 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/153),(50/64/102)
−
LAT_100%NDR: ['60/119/175', '50/92/167']
+
LAT_10%NDR:(50/57/112),(50/60/117)
−
LAT_50%NDR: ['50/64/153', '50/64/102']
+
−
LAT_10%NDR: ['50/57/112', '50/60/117']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 277160.0 pps (2x 138580.0 pps)  
+
|RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/135/184 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/152/173 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: IMIX_v4_1 PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC20: IMIX_v4_1 PDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)  
+
|RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Intel-XL710=====
 
=====Long Xconnect Intel-XL710=====
  
−
*'''RFC2544: Pkt throughput L2XC test cases'''
+
*'''RFC2544: Pkt throughput L2XC test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 5,786: Line 4,493:
 
|TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 9525000.0 pps (2x 4762500.0 pps)  
+
|RATE: 9525000 pps (2x 4762500 pps) BANDWIDTH: 6.400 Gbps (untagged)
−
FINAL_BANDWIDTH: 6.4008 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/159),(10/27/172)
−
LAT_100%NDR: ['30/398/494', '10/360/498']
+
LAT_10%NDR:(10/23/72),(10/22/80)
−
LAT_50%NDR: ['10/28/159', '10/27/172']
+
−
LAT_10%NDR: ['10/23/72', '10/22/80']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 3703834.65624 pps (2x 1851917.32812 pps)  
+
|RATE: 3703834 pps (2x 1851917 pps) BANDWIDTH: 45.571 Gbps (untagged)
−
FINAL_BANDWIDTH: 45.5719816104 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/27/51),(10/26/56)
−
LAT_100%NDR: ['20/34/69', '10/34/64']
+
LAT_10%NDR:(20/28/74),(10/28/57)
−
LAT_50%NDR: ['10/27/51', '10/26/56']
+
−
LAT_10%NDR: ['20/28/74', '10/28/57']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 15644531.25 pps (2x 7822265.625 pps)  
+
|RATE: 15644531 pps (2x 7822265 pps) BANDWIDTH: 10.513 Gbps (untagged)
−
FINAL_BANDWIDTH: 10.513125 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/22/62),(10/21/168)
−
LAT_100%NDR: ['10/28/77', '10/30/101']
+
LAT_10%NDR:(10/24/60),(10/25/40)
−
LAT_50%NDR: ['10/22/62', '10/21/168']
+
−
LAT_10%NDR: ['10/24/60', '10/25/40']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 3734791.25 pps (2x 1867395.625 pps)  
+
|RATE: 3734791 pps (2x 1867395 pps) BANDWIDTH: 45.952 Gbps (untagged)
−
FINAL_BANDWIDTH: 45.95287154 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/143),(10/26/86)
−
LAT_100%NDR: ['10/33/165', '10/33/214']
+
LAT_10%NDR:(20/26/67),(10/25/82)
−
LAT_50%NDR: ['10/28/143', '10/26/86']
+
−
LAT_10%NDR: ['20/26/67', '10/25/82']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 30797656.25 pps (2x 15398828.125 pps)  
+
|RATE: 30797656 pps (2x 15398828 pps) BANDWIDTH: 20.696 Gbps (untagged)
−
FINAL_BANDWIDTH: 20.696025 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/16/109),(10/16/151)
−
LAT_100%NDR: ['10/28/116', '10/27/100']
+
LAT_10%NDR:(10/20/33),(10/19/32)
−
LAT_50%NDR: ['10/16/109', '10/16/151']
+
−
LAT_10%NDR: ['10/20/33', '10/19/32']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)  
+
|RATE: 3982444 pps (2x 1991222 pps) BANDWIDTH: 48.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/29/146),(10/27/119)
−
LAT_100%NDR: ['10/33/93', '20/33/174']
+
LAT_10%NDR:(10/27/72),(10/26/158)
−
LAT_50%NDR: ['10/29/146', '10/27/119']
+
−
LAT_10%NDR: ['10/27/72', '10/26/158']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 9556551.90624 pps (2x 4778275.95312 pps)  
+
|RATE: 9556551 pps (2x 4778275 pps) BANDWIDTH: 28.580 Gbps (untagged)
−
FINAL_BANDWIDTH: 28.5804609794 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: IMIX_v4_1 NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|TC20: IMIX_v4_1 NDR binary search - DUT L2XC - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 16384306.0 pps (2x 8192153.0 pps)  
+
|RATE: 16384306 pps (2x 8192153 pps) BANDWIDTH: 48.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 48.9999973738 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC21: IMIX_v4_1 NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|TC21: IMIX_v4_1 NDR binary search - DUT L2XC - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 thread, 4 phy core,  2 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 4 thread, 4 phy core,  2 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 16384306.0 pps (2x 8192153.0 pps)  
+
|RATE: 16384306 pps (2x 8192153 pps) BANDWIDTH: 48.999 Gbps (untagged)
−
FINAL_BANDWIDTH: 48.9999973738 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Vhost Intel-X520-DA2=====
 
=====Long Xconnect Vhost Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2XC test cases with vhost'''
+
*'''RFC2544: Pkt throughput L2XC test cases with vhost'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross connect.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
*'''[Ref] Applicable standard specifications:''' RFC2544.
 
{| class="wikitable"
 
{| class="wikitable"
Line 5,887: Line 4,567:
 
|TC01: 64B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 542806.90625 pps (2x 271403.453125 pps)  
+
|RATE: 542806 pps (2x 271403 pps) BANDWIDTH: 0.364 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.364766241 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/29/352),(10/29/167)
−
LAT_100%NDR: ['10/31/353', '10/31/159']
+
LAT_10%NDR:(10/22/298),(10/22/91)
−
LAT_50%NDR: ['10/29/352', '10/29/167']
+
−
LAT_10%NDR: ['10/22/298', '10/22/91']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 2575944.875 pps (2x 1287972.4375 pps)  
+
|RATE: 2575944 pps (2x 1287972 pps) BANDWIDTH: 1.731 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 1.731034956 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/115/381 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/119/442 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 270857.1875 pps (2x 135428.59375 pps)  
+
|RATE: 270857 pps (2x 135428 pps) BANDWIDTH: 3.332 Gbps (untagged)
−
FINAL_BANDWIDTH: 3.332626835 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/31/313),(20/31/356)
−
LAT_100%NDR: ['20/45/341', '20/46/367']
+
LAT_10%NDR:(20/30/337),(20/30/358)
−
LAT_50%NDR: ['20/31/313', '20/31/356']
+
−
LAT_10%NDR: ['20/30/337', '20/30/358']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1324457.375 pps (2x 662228.6875 pps)  
+
|RATE: 1324457 pps (2x 662228 pps) BANDWIDTH: 16.296 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 16.296123542 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/592/883 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/594/853 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC05: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 362132.3125 pps (2x 181066.15625 pps)  
+
|RATE: 362132 pps (2x 181066 pps) BANDWIDTH: 1.083 Gbps (untagged)
−
FINAL_BANDWIDTH: 1.08301702626 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|TC06: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 2044542.25 pps (2x 1022271.125 pps)  
+
|RATE: 2044542 pps (2x 1022271 pps) BANDWIDTH: 6.114 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 6.11454430115 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 542806.90625 pps (2x 271403.453125 pps)  
+
|RATE: 542806 pps (2x 271403 pps) BANDWIDTH: 0.364 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.364766241 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/21/376),(10/25/102)
−
LAT_100%NDR: ['10/25/387', '10/23/84']
+
LAT_10%NDR:(10/22/469),(10/19/69)
−
LAT_50%NDR: ['10/21/376', '10/25/102']
+
−
LAT_10%NDR: ['10/22/469', '10/19/69']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 4521948.35938 pps (2x 2260974.17969 pps)  
+
|RATE: 4521948 pps (2x 2260974 pps) BANDWIDTH: 3.038 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.0387492975 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/72/425 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/90/173 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 396285.78125 pps (2x 198142.890625 pps)  
+
|RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.8759002525 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/32/339),(20/29/368)
−
LAT_100%NDR: ['20/32/408', '20/35/389']
+
LAT_10%NDR:(20/29/311),(20/27/342)
−
LAT_50%NDR: ['20/32/339', '20/29/368']
+
−
LAT_10%NDR: ['20/29/311', '20/27/342']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/404/475 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/379/517 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC11: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 870767.875 pps (2x 435383.9375 pps)  
+
|RATE: 870767 pps (2x 435383 pps) BANDWIDTH: 2.604 Gbps (untagged)
−
FINAL_BANDWIDTH: 2.60417643495 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|TC12: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 3961707.0625 pps (2x 1980853.53125 pps)  
+
|RATE: 3961707 pps (2x 1980853 pps) BANDWIDTH: 11.848 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 11.8481451493 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 717075.875 pps (2x 358537.9375 pps)  
+
|RATE: 717075 pps (2x 358537 pps) BANDWIDTH: 0.481 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.481874988 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/22/342),(10/21/313)
−
LAT_100%NDR: ['10/22/318', '10/24/380']
+
LAT_10%NDR:(10/11/356),(10/11/329)
−
LAT_50%NDR: ['10/22/342', '10/21/313']
+
−
LAT_10%NDR: ['10/11/356', '10/11/329']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 4754306.98438 pps (2x 2377153.49219 pps)  
+
|RATE: 4754306 pps (2x 2377153 pps) BANDWIDTH: 3.194 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.1948942935 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/47/119 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/66/402 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 396285.78125 pps (2x 198142.890625 pps)  
+
|RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)
−
FINAL_BANDWIDTH: 4.8759002525 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/31/174),(20/30/314)
−
LAT_100%NDR: ['20/34/83', '20/35/349']
+
LAT_10%NDR:(20/27/54),(20/30/354)
−
LAT_50%NDR: ['20/31/174', '20/30/314']
+
−
LAT_10%NDR: ['20/27/54', '20/30/354']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)  
+
|RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/377/404 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/284/528 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC17: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 557761.375 pps (2x 278880.6875 pps)  
+
|RATE: 557761 pps (2x 278880 pps) BANDWIDTH: 1.668 Gbps (untagged)
−
FINAL_BANDWIDTH: 1.66807833729 Gbps (untagged)  
+
−
LATENCY usec [min/avg/max]
+
−
LAT_100%NDR: ['0/0/0', '0/0/0']
+
−
LAT_50%NDR: ['0/0/0', '0/0/0']
+
−
LAT_10%NDR: ['0/0/0', '0/0/0']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|TC18: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
 
|[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame  size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
−
|FINAL_RATE: 4222545.8125 pps (2x 2111272.90625 pps)  
+
|RATE: 4222545 pps (2x 2111272 pps) BANDWIDTH: 12.628 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.6282268973 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 0/0/0 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 0/0/0 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC19: 64B NDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq
 
|TC19: 64B NDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 426627.59375 pps (2x 213313.796875 pps)  
+
|RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)
−
FINAL_BANDWIDTH: 0.286693743 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/24/102),(10/24/356)
−
LAT_100%NDR: ['10/23/116', '10/29/382']
+
LAT_10%NDR:(10/22/72),(10/22/327)
−
LAT_50%NDR: ['10/24/102', '10/24/356']
+
−
LAT_10%NDR: ['10/22/72', '10/22/327']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC20: 64B PDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq
 
|TC20: 64B PDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames  using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 2314541.42188 pps (2x 1157270.71094 pps)  
+
|RATE: 2314541 pps (2x 1157270 pps) BANDWIDTH: 1.555 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 1.5553718355 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/104/285 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/98/283 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
 
=====Long Xconnect Vxlan Ipv4 Intel-X520-DA2=====
 
=====Long Xconnect Vxlan Ipv4 Intel-X520-DA2=====
  
−
*'''RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases'''
+
*'''RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases'''
−
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.  
+
*'''[Top] Network Topologies:''' TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
−
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.  
+
*'''[Enc] Packet Encapsulations:''' Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
−
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.  
+
*'''[Cfg] DUT configuration:''' DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
−
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.  
+
*'''[Ver] TG verification:''' TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
 
*'''[Ref] Applicable standard specifications:''' RFC2544, RFC7348.
 
*'''[Ref] Applicable standard specifications:''' RFC2544, RFC7348.
 
{| class="wikitable"
 
{| class="wikitable"
Line 6,088: Line 4,699:
 
|TC01: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC01: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 5390951.375 pps (2x 2695475.6875 pps)  
+
|RATE: 5390951 pps (2x 2695475 pps) BANDWIDTH: 3.622 Gbps (untagged)
−
FINAL_BANDWIDTH: 3.622719324 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/32/644),(10/32/624)
−
LAT_100%NDR: ['50/2539/2726', '60/3938/4079']
+
LAT_10%NDR:(10/22/637),(10/19/614)
−
LAT_50%NDR: ['10/32/644', '10/32/624']
+
−
LAT_10%NDR: ['10/22/637', '10/19/614']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC02: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC02: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 5390951.375 pps (2x 2695475.6875 pps)  
+
|RATE: 5390951 pps (2x 2695475 pps) BANDWIDTH: 3.622 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 3.622719324 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 10/2505/2607 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 10/1760/1879 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC03: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC03: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/31/584),(20/34/656)
−
LAT_100%NDR: ['20/160/220', '20/169/311']
+
LAT_10%NDR:(20/26/132),(20/28/149)
−
LAT_50%NDR: ['20/31/584', '20/34/656']
+
−
LAT_10%NDR: ['20/26/132', '20/28/149']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC04: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC04: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/195/342 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/218/387 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC05: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC05: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/65/191),(50/67/192)
−
LAT_100%NDR: ['50/172/199', '50/159/278']
+
LAT_10%NDR:(50/58/89),(50/61/156)
−
LAT_50%NDR: ['50/65/191', '50/67/192']
+
−
LAT_10%NDR: ['50/58/89', '50/61/156']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC06: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|TC06: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 60/169/204 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 50/154/272 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC07: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC07: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 10870288.9375 pps (2x 5435144.46875 pps)  
+
|RATE: 10870288 pps (2x 5435144 pps) BANDWIDTH: 7.304 Gbps (untagged)
−
FINAL_BANDWIDTH: 7.304834166 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/28/56),(10/29/109)
−
LAT_100%NDR: ['20/59/700', '30/76/687']
+
LAT_10%NDR:(10/19/40),(10/20/66)
−
LAT_50%NDR: ['10/28/56', '10/29/109']
+
−
LAT_10%NDR: ['10/19/40', '10/20/66']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC08: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC08: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 11158675.125 pps (2x 5579337.5625 pps)  
+
|RATE: 11158675 pps (2x 5579337 pps) BANDWIDTH: 7.498 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 7.498629684 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/1176/1216 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/1219/1298 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC09: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC09: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(20/28/109),(20/29/155)
−
LAT_100%NDR: ['20/95/697', '20/108/677']
+
LAT_10%NDR:(20/26/89),(20/25/84)
−
LAT_50%NDR: ['20/28/109', '20/29/155']
+
−
LAT_10%NDR: ['20/26/89', '20/25/84']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC10: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC10: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/161/210 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/165/264 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC11: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC11: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/67/192),(50/67/145)
−
LAT_100%NDR: ['50/154/218', '50/101/193']
+
LAT_10%NDR:(50/61/141),(50/60/106)
−
LAT_50%NDR: ['50/67/192', '50/67/145']
+
−
LAT_10%NDR: ['50/61/141', '50/60/106']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC12: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|TC12: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,  1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/114/202 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/99/241 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC13: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC13: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
−
|FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)  
+
|RATE: 18656716 pps (2x 9328358 pps) BANDWIDTH: 12.537 Gbps (untagged)
−
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(10/25/104),(10/26/157)
−
LAT_100%NDR: ['20/178/649', '20/166/622']
+
LAT_10%NDR:(10/20/67),(10/19/76)
−
LAT_50%NDR: ['10/25/104', '10/26/157']
+
−
LAT_10%NDR: ['10/20/67', '10/19/76']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC14: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC14: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
−
|FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)  
+
|RATE: 18656716 pps (2x 9328358 pps) BANDWIDTH: 12.537 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/167/304 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/152/347 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC15: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC15: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(2/27/99),(20/28/84)
−
LAT_100%NDR: ['20/114/194', '20/110/258']
+
LAT_10%NDR:(20/26/553),(20/27/629)
−
LAT_50%NDR: ['2/27/99', '20/28/84']
+
−
LAT_10%NDR: ['20/26/553', '20/27/629']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC16: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC16: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
−
|FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)  
+
|RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 20/116/177 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 20/85/147 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC17: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC17: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
LATENCY [usec] (min/avg/max)
−
LATENCY usec [min/avg/max]
+
LAT_50%NDR:(50/64/770),(50/64/724)
−
LAT_100%NDR: ['50/119/231', '60/129/243']
+
LAT_10%NDR:(50/58/119),(50/58/97)
−
LAT_50%NDR: ['50/64/770', '50/64/724']
+
−
LAT_10%NDR: ['50/58/119', '50/58/97']
+
 
|PASS
 
|PASS
 
|-
 
|-
 
|TC18: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|TC18: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
 
|[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,  2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
−
|FINAL_RATE: 275632.0 pps (2x 137816.0 pps)  
+
|RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5%
−
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)  
+
−
LATENCY_STREAM_0: 50/103/420 usec (min/avg/max)
+
−
LATENCY_STREAM_1: 60/134/401 usec (min/avg/max)
+
−
LOSS_ACCEPTANCE: 0.5 percentage
+
 
|PASS
 
|PASS
 
|}
 
|}
Line 6,466: Line 5,023:
 
|FAIL
 
|FAIL
 
|}
 
|}
−
 
−
=Failed Performance Tests=
 

Revision as of 12:29, 26 September 2016

DRAFT CONTENT - WORK IN PROGRESS

Contents

Introduction

This report aims to provide a comprehensive and self-explanatory summary of all CSIT test cases that have been executed against FD.io VPP-16.09 code release, driven by the automated test infrastructure developed within the FD.io CSIT project (FD.io Continuous System and Integration Testing).

CSIT source code for the executed test suites is available in CSIT branch rls1609 in the directory ./tests/<name_of_the_test_suite>. A local copy of CSIT source code can be obtained by cloning CSIT git repository ("git clone https://gerrit.fd.io/r/csit"). The CSIT testing virtual environment can be run on a local workstation/laptop/server using Vagrant by following the instructions in CSIT tutorials.

Followings sections provide brief description of CSIT performance and functional test suites executed against VPP-16.09 release (vpp branch stable/1609). Description of LF FD.io virtual and physical test environments is provided to aid anyone interested in reproducing the complete LF FD.io CSIT testing environment, in either virtual or physical test beds. The last two sections cover complete list of CSIT test suites and test cases executed against VPP-16.09 release (vpp branch stable/1609), with description and results per test case.

Functional Tests

Overview

Functional tests run on virtual testbeds which are created in VIRL running on a Cisco UCS C240 servers hosted in Linux Foundation labs. There is currently only one testbed topology being used for functional testing - a three node topology with two links between each pair of nodes as shown in this diagram: 

    +--------+                      +--------+
    |        |                      |        |
    |  SUT1  <---------------------->  SUT2  |
    |        |                      |        |
    +---^----+                      +----^---+
        |                                |
        |                                |
        |           +-------+            |
        |           |       |            |
        +----------->   TG  <------------+
                    |       |
                    +-------+

Virtual testbeds are created dynamically whenever a patch is submitted to gerrit and destroyed upon completion of all functional tests. During test execution, all nodes are reachable thru the MGMT network connected to every node via dedicated NICs and links (not shown above for clarity). Each node is a Virtual Machine and each connection that is drawn on the diagram is available for use in any test case.

For test cases that require DUT (VPP) to communicate with VM over vhost-user interfaces, a nested VM is created on SUT1 and/or SUT2 for the duration of that particular test case only. DUT (VPP) test topology with VM is shown in the diagram below including the packet flow (marked with ***): 

    +------------------------+           +------------------------+
    |      +----------+      |           |      +----------+      |
    |      |    VM    |      |           |      |    VM    |      |
    |      |  ******  |      |           |      |  ******  |      |
    |      +--^----^--+      |           |      +--^----^--+      |
    |        *|    |*        |           |        *|    |*        |
    |  +------v----v------+  |           |  +------v----v------+  |
    |  |      *    *      |**|***********|**|      *    *      |  |
    |  |  *****    *******<----------------->*******    *****  |  |
    |  |  *    DUT1       |  |           |  |       DUT2    *  |  |
    |  +--^---------------+  |           |  +---------------^--+  |
    |    *|                  |           |                  |*    |
    |    *|            SUT1  |           |  SUT2            |*    |
    +------------------------+           +------------------^-----+
         *|                                                 |*
         *|                                                 |*
         *|                  +-----------+                  |*
         *|                  |           |                  |*
         *+------------------>    TG     <------------------+*
         ******************* |           |********************
                             +-----------+

The following functional test suites are included in the CSIT-16.09 Release and this report - test areas added since CSIT-16.06 got marked with [&], extended areas marked with [%]:

  1. L2XC [%] - L2 Cross-Connect switching of Ethernet frames (untagged, VLAN single-tag 802.1q, double-tag 802.1ad).
  2. L2BD [%] - L2 Bridge-Domain switching of Ethernet frames (untagged, 802.1q, 802.1ad).
  3. IPv4 [%] - IPv4 routed-forwarding, RPF, ARP, Proxy ARP, ICMPv4.
  4. IPv6 [%] - IPv6 routed-forwarding, NS/ND, RA, ICMPv6.
  5. DHCP [%] - DHCP Client and Proxy (IPv4, IPv6).
  6. VXLAN - VXLAN tunnelling dataplane with L2BD, L2XC (untagged, 802.1q).
  7. COP - COP address security, white-listing and black-listing (IPv4, IPv6).
  8. GRE [%] - GRE tunnelling dataplane with IP routed-forwarding (IPv4).
  9. LISP [%] - LISP tunneling dataplane with IP routed-forwarding (IPv4) and API functionality.
  10. iACL [%] - Ingress Access Control List security (IPv4, IPv6, L2).
  11. VRF [&] - IP VPN routed-forwarding (IPv4, IPv6).
  12. QoS Policer [&] - ingress packet rate measuring, marking and limiting (IPv4, IPv6).
  13. IPFIX [&] - IPFIX Netflow (IPv4, IPv6).
  14. IPSec [&] - IPSec transport and tunnel mode (IPv4, IPv6).
  15. Softwire [&] - IPv4-over-IPv6 Softwire Concentration including LightWeight4over6, MAP-E, MAP-T.
  16. VLAN rewrites [&] - L2 VLAN rewrite tests 2-2, 2-1, 1-2 with L2XC and L2BD.
  17. Tap Interface [&] - baseline Linux tap interface tests.
  18. HoneyComb [&] - HoneyComb control plane interface into VPP.

Total 199 functional tests in the CSIT-16.09 Release (up from 76 functional tests in the CSIT-16.06 Release).

Test Execution Environment

CSIT functional tests are currently executed in VIRL, as mentioned above. The physical VIRL testbed infrastructure consists of three identical VIRL hosts, each host being a Cisco UCS C240-M4 (2x Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz, 18c, 512GB RAM) running Ubuntu 14.04.3 and the following VIRL software versions: 

 STD server version 0.10.24.7
 UWM server version 0.10.24.7

Whenever a patch is submitted to gerrit for review, one of the three VIRL hosts is selected randomly, and a three-node (TG+SUT1+SUT2), "double-ring" topology is created as a VIRL simulation on the selected host. The binary Debian VPP packages built by Jenkins for the patch under review are then installed on the two SUTs, along with their /etc/vpp/startup.conf file.

Current VPP 16.09 tests have been executed on a single VM operating system and version only, as described in the following paragraphs.

In order to enable future testing with different Operating Systems, or with different versions of the same Operating System, and simultaneously allowing others to reproduce tests in the exact same environment, CSIT has established a process where a candidate Operating System (currently only Ubuntu 14.04.4 LTS) plus all required packages are installed, and the versions of all installed packages are recorded. A separate tool then creates, and will continue to create at any point in the future, a disk image with these packages and their exact versions. Identical sets of disk images are created in QEMU/QCOW2 format for use within VIRL, and in VirtualBox format for use in the CSIT Vagrant environment.

In CSIT terminology, the VM operating system for both SUTs and TG that VPP 16.09 has been tested with, is the following: 

 ubuntu-14.04.4_2016-05-25_1.0

which implies Ubuntu 14.04.4 LTS, current as of 2016/05/25 (that is, package versions are those that would have been installed by a "apt-get update", "apt-get upgrade" on May 25), produced by CSIT disk image build scripts version 1.0.

The exact list of installed packages and their versions (including the Linux kernel package version) are included in CSIT source repository: 

 resources/tools/disk-image-builder/ubuntu/lists/ubuntu-14.04.4_2016-05-25_1.0

A replica of this VM image can be built by running the "build.sh" script in CSIT repository resources/tools/disk-image-builder/, or by downloading the Vagrant box from Atlas: 

 https://atlas.hashicorp.com/fdio-csit/boxes/ubuntu-14.04.4_2016-05-25_1.0

In addition to this "main" VM image, tests which require VPP to communicate to a VM over a vhost-user interface, utilize a "nested" VM image.

This "nested" VM is dynamically created and destroyed as part of a test case, and therefore the "nested" VM image is optimized to be small, lightweight and have a short boot time. The "nested" VM image is not built around any established Linux distribution, but is based on BuildRoot (https://buildroot.org/), a tool for building embedded Linux systems. Just as for the "main" image, scripts to produce an identical replica of the "nested" image are included in CSIT GIT repository, and the image can be rebuilt using the "build.sh" script at: 

  resources/tools/disk-image-builder/ubuntu/lists/nested

Functional tests utilize Scapy version 2.3.1 as a traffic generator.

Performance Tests

Overview

Performance tests run on physical testbeds hosted in Linux Foundation labs and consist of three Cisco UCS C240 servers each with 2x XEON CPUs (E5-2699v3 2.3GHz 18c). The logical testbed topology is fundamentally the same structure as the functional testbeds, but for any given tests, there is only a single link between each pair of nodes as shown in this diagram: 

    +--------+                      +--------+
    |        |                      |        |
    |  SUT1  <---------------------->  SUT2  |
    |        |                      |        |
    +---^----+                      +----^---+
        |                                |
        |                                |
        |           +-------+            |
        |           |       |            |
        +----------->   TG  <------------+
                    |       |
                    +-------+

At a physical level there are actually five units of 10GE and 40GE NICs per SUT made by different vendors: Intel 2p10GE NICs (x520, x710), Intel 40GE NICs (xl710), Cisco 2p10GE VICs, Cisco 2p40GE VICs. During test execution, all nodes are reachable thru the MGMT network connected to every node via dedicated NICs and links (not shown above for clarity). Currently the performance tests only utilize one model of Intel NICs. Detailed test bed specification and topology is described in CSIT/CSIT_LF_testbed.

For test cases that require DUT (VPP) to communicate with VM over vhost-user interfaces, a VM is created on SUT1 and SUT2. DUT (VPP) test topology with VM is shown in the diagram below including the packet flow (marked with ***): 

    +------------------------+           +------------------------+
    |      +----------+      |           |      +----------+      |
    |      |    VM    |      |           |      |    VM    |      |
    |      |  ******  |      |           |      |  ******  |      |
    |      +--^----^--+      |           |      +--^----^--+      |
    |        *|    |*        |           |        *|    |*        |
    |  +------v----v------+  |           |  +------v----v------+  |
    |  |      *    *      |**|***********|**|      *    *      |  |
    |  |  *****    *******<----------------->*******    *****  |  |
    |  |  *    DUT1       |  |           |  |       DUT2    *  |  |
    |  +--^---------------+  |           |  +---------------^--+  |
    |    *|                  |           |                  |*    |
    |    *|            SUT1  |           |  SUT2            |*    |
    +------------------------+           +------------------^-----+
         *|                                                 |*
         *|                                                 |*
         *|                  +-----------+                  |*
         *|                  |           |                  |*
         *+------------------>    TG     <------------------+*
         ******************* |           |********************
                             +-----------+

Note that for VM tests, packets are switched by DUT (VPP) twice, hence the throughput rates measured by TG must be multiplied by two to represent the actual DUT packet forwarding rate.

Because performance testing is run on physical test beds and some tests require a long time to complete, the performance test jobs have been split into short duration and long duration variants. The long performance jobs are run on a periodic basis and run all of the long performance test suites discovering throughput rates - NDR (Non-Drop Rate) and PDR (Partial Drop Rate) - and measuring packet latency. The short performance jobs are run on demand and run the short performance test suites verifying packet throughput against the reference NDR rates. There are also separate test suites for each NIC type.

The following performance test suites are included in the CSIT-16.09 Release and measurements listed in this report - test areas added since CSIT-16.06 got marked with "[&]", extended areas marked with "[%]":

  • Long performance test suites with Intel X520-DA2 NIC (2 port 10GbE) - total of 469 tests:
    1. L2XC - NDR & PDR for L2 Cross-Connect switched-forwarding of untagged and QinQ, 801.2Q Vlan, VXLAN tagged packets.
    2. L2BD - NDR & PDR for L2 Bridge Domain switched-forwarding.
    3. IPv4 - NDR & PDR for IPv4 routed-forwarding.
    4. IPv6 - NDR & PDR for IPv6 routed-forwarding.
    5. COP - NDR & PDR for IPv4 and IPv6 routed-forwarding with COP address security.
    6. iACL - NDR & PDR for IPv4 and IPv6 routed-forwarding with iACL address security.
    7. LISP [&] - NDR & PDR for LISP tunneling dataplane with IP routed-forwarding (IPv4).
    8. VXLAN [&] - NDR & PDR for VXLAN tunnelling integration with L2XC.
    9. QoS Policer [&] - NDR & PDR for ingress packet rate measuring, marking and limiting (IPv4).
    10. IPv4 Scale [&] - NDR & PDR for IPv4 routed-forwarding with 20K, 200K, 2M FIB entries.
    11. IPv6 Scale [&] - NDR & PDR for IPv6 routed-forwarding with 20K, 200K, 2M FIB entries.
    12. vhost-user [&] - NDR & PDR for L2 Cross-Connect, L2 Bridge-Domain, IPv4 routed-forwarding with VM over vhost-user interface.
  • Long performance test suites with Intel XL-710 NIC (2 ports 40GbE) - total of 9 tests:
    1. L2 Cross-Connect [&] - NDR & PDR for L2 Cross-Connect switched-forwarding of untagged and QinQ, 801.2Q Vlan, VXLAN tagged packets.
    2. L2 Bridge-Domain [&] - NDR & PDR for L2 Bridge Domain switched-forwarding. (results to be added)
    3. IPv4 [&] - NDR & PDR for IPv4 routed-forwarding. (results to be added)
    4. IPv6 [&] - NDR & PDR for IPv6 routed-forwarding. (results to be added)
  • Short performance test suites with Intel X520-DA2 NIC (2 port 10GbE) - total of 198 tests:
    1. L2XC - L2 Cross-Connect switched-forwarding of untagged and QinQ, 801.2Q Vlan, VXLAN tagged packets.
    2. L2BD - L2 Bridge Domain switched-forwarding.
    3. IPv4 - IPv4 routed-forwarding.
    4. IPv6 - IPv6 routed-forwarding.
    5. COP - IPv4 and IPv6 routed-forwarding with COP address security.
    6. iACL - IPv4 and IPv6 routed-forwarding with iACL address security.
    7. LISP [&] - LISP tunneling dataplane with IP routed-forwarding (IPv4).
    8. VXLAN [&] - VXLAN tunnelling integration with L2XC.
    9. QoS Policer [&] - ingress packet rate measuring, marking and limiting (IPv4).
    10. IPv4 Scale [&] - IPv4 routed-forwarding with 20K, 200K, 2M FIB entries.
    11. IPv6 Scale [&] - IPv6 routed-forwarding with 20K, 200K, 2M FIB entries.
    12. vhost-user [&] - L2 Cross-Connect, L2 Bridge-Domain, IPv4 routed-forwarding with VM over vhost-user interface.

Caveats and Notes

Latency Measurements

TRex traffic generator (TG) new (experimental) functionality is used for measuring latency of VPP SUTs. Reported latency values are measured using following methodology:

  • Latency tests are performed at 10%, 50% and 100% of discovered NDR rate (non drop rate) for each throughput test and packet size except IMIX.
  • TG sends dedicated latency streams, one per direction, each at the rate of 10kpps at the prescribed packet size; these are sent in addition to the main load streams.
  • TG reports min/avg/max latency values; future release of TRex is expected to report latency percentiles.
  • Reported latency values are aggregate across two SUTs due to three node topology used for all performance tests; for per SUT latency, reported value should be divided by two.
  • 1usec is measurements accuracy advertised by TRex TG for the setup used in FD.io labs.
  • TRex setup introduces an always-on error of about 2*2usec per latency flow - additonal Tx/Rx interface latency induced by TRex SW writing and reading packet timestamps on CPU cores without HW acceleration on NICs closer to the interface line.

VM vhost-user Throughput Measurements

Current setup of CSIT FD.io performance lab is using default Ubuntu 14.04.02 KVM Qemu settings:

  • Default Qemu virtio queue size of 256 descriptors.
  • Default Linux CFS scheduler settings.

These default settings make the performance of VPP+VM system very sensitive to any OS system tasks (i.e. Linux kernel) interference on CPU cores that are designated for critical software tasks under test, namely VPP worker threads in host and Testpmd threads in guest. CSIT committers decided against tweaking listed default settings. Instead we decided to list the performance numbers with default settings in CSIT-16.09 report. Hence reported results are not fully representative of VPP vhost capabilities. If in doubt please refer to VPP vhost throughput numbers reported on csit-dev mailer by folks testing it in their labs.

Going forward, once integrated into CSIT system, we want to add a separate set of tests with adjusted default parameters namely i) increased Qemu virtio queue size to 1024 descriptors, ii) consider adjusting CFS scheduler settings for tasks under test. Both are subject to ongoing improvements in Qemu code (see added vhost functionality in Qemu 2.7) and VPP vhost-user driver (see vhost indirect descriptors patch).

VPP Trend Graphs RFC2544:NDR

VPP performance trend graphs from LF Jenkins Job csit-vpp-perf-1609-long.

L2XC, L2BD - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq IPv4 - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq IPv6 - RFC2544 NDR at 78B, 1 worker-thread, 1 rxq VXLAN+L2BD - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq LISP+IPv4 - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq LISP+IPv6 - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq vhost-to-VM - RFC2544 NDR at 64B, 1 worker-thread, 1 rxq

L2XC, L2BD - RFC2544 NDR at 64B, 2 worker-threads, 2 rxq IPv4 - RFC2544 NDR at 64B, 2 worker-threads, 2 rxq IPv6 - RFC2544 NDR at 78B, 2 worker-threads, 2 rxq VXLAN+L2BD, LISP+IPv4 - RFC2544 NDR at 64B, 2 worker-threads, 2 rxq LISP+IPv6 - RFC2544 NDR at 64B, 2 worker-threads, 2 rxq vhost-to-VM - RFC2544 NDR at 64B, 2 worker-threads, 2 rxq

L2XC, L2BD - RFC2544 NDR at 64B, 4 worker-threads, 2 rxq IPv4 - RFC2544 NDR at 64B, 4 worker-threads, 2 rxq IPv6 - RFC2544 NDR at 78B, 4 worker-threads, 2 rxq VXLAN+L2BD, LISP+IPv4 - RFC2544 NDR at 64B, 4 worker-threads, 2 rxq LISP+IPv6 - RFC2544 NDR at 64B, 4 worker-threads, 2 rxq vhost-to-VM - RFC2544 NDR at 64B, 4 worker-threads, 2 rxq

VPP Trend Graphs RFC2544:PDR

VPP performance trend graphs from LF Jenkins Job csit-vpp-perf-1609-all.

[TBD]

Test Execution Environment

To execute performance tests, there are three identical testbeds, each testbed consists of two SUTs and one TG.

Hardware details (CPU, memory, NIC layout) are described in CSIT/CSIT_LF_testbed; in summary:

  • All hosts are Cisco UCS C240-M4 (2x Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz, 18c, 512GB RAM),
  • BIOS settings are default except for the following:
    • Hyperthreading disabled,
    • SpeedStep disabled
    • TurboBoost disabled
    • Power Technology: Performance
  • Hosts run Ubuntu 14.04.3, kernel 4.2.0-36-generic
  • Linux kernel boot command line option "intel_pstate=disable" is applied to both SUTs and TG. In addition, on SUTs, only cores 0 and 18 (the first core on each socket) are available to the Linux operating system and generic tasks, all other CPU cores are isolated and reserved for VPP.
  • In addition to CIMC and Management, each TG has 4x Intel X710 10GB NIC (=8 ports) and 2x Intel XL710 40GB NIC (=4 ports), whereas each SUT has:
    • 1x Intel X520 NIC (10GB, 2 ports),
    • 1x Cisco VIC 1385 (40GB, 2 ports),
    • 1x Intel XL710 NIC (40GB, 2 ports),
    • 1x Intel X710 NIC (10GB, 2 ports),
    • 1x Cisco VIC 1227 (10GB, 2 ports). This allows for a total of five "double-ring" topologies, each using a different NIC.

Config: VPP (DUT)

NIC types 

0a:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)
        Subsystem: Intel Corporation Ethernet Server Adapter X520-2
0a:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)
        Subsystem: Intel Corporation Ethernet Server Adapter X520-2
85:00.0 Ethernet controller: Intel Corporation Ethernet Controller XL710 for 40GbE QSFP+ (rev 01)
        Subsystem: Intel Corporation Ethernet Converged Network Adapter XL710-Q2
85:00.1 Ethernet controller: Intel Corporation Ethernet Controller XL710 for 40GbE QSFP+ (rev 01)
        Subsystem: Intel Corporation Ethernet Converged Network Adapter XL710-Q2

VPP Version

vpp-16.09_amd64

VPP Compile Parameters

VPP Compile Job: https://jenkins.fd.io/view/vpp/job/vpp-merge-1609-ubuntu1404/

VPP Install Parameters 

$ dpkg -i --force-all

VPP Startup Configuration

VPP startup configuration changes per test case with different settings for CPU cores, rx-queues and no-multi-seg parameter. Startup config is aligned with applied test case tag:

Tagged by: 1_THREAD_NOHTT_RXQUEUES_1 

$ cat /etc/vpp/startup.conf
unix {
  nodaemon
  log /tmp/vpe.log
  cli-listen localhost:5002
  full-coredump
}

api-trace {
  on
}

cpu {
  main-core 0 corelist-workers 1
}

dpdk {
  socket-mem 1024,1024
  dev default {
    num-rx-queues 1
  }
  dev 0000:0a:00.1
  dev 0000:0a:00.0
  no-multi-seg
}

ip6 {
  hash-buckets 2000000
  heap-size 500m
}

Tagged by: 2_THREAD_NOHTT_RXQUEUES_1 

$ cat /etc/vpp/startup.conf
unix {
  nodaemon
  log /tmp/vpe.log
  cli-listen localhost:5002
  full-coredump
}

api-trace {
  on
}

cpu {
  main-core 0 corelist-workers 1-2
}

dpdk {
  socket-mem 1024,1024
  dev default {
    num-rx-queues 1
  }
  dev 0000:0a:00.1
  dev 0000:0a:00.0
  no-multi-seg
}

ip6 {
  hash-buckets 2000000
  heap-size 500m
}

Tagged by: 4_THREAD_NOHTT_RXQUEUES_2 

$ cat /etc/vpp/startup.conf
unix {
  nodaemon
  log /tmp/vpe.log
  cli-listen localhost:5002
  full-coredump
}

api-trace {
  on
}

cpu {
  main-core 0 corelist-workers 1-4
}

dpdk {
  socket-mem 1024,1024
  dev default {
    num-rx-queues 2
  }
  dev 0000:0a:00.1
  dev 0000:0a:00.0
  no-multi-seg
}

ip6 {
  hash-buckets 2000000
  heap-size 500m
}

Config: Traffic Generator - TRex

TG Version

TRex v2.07

DPDK version

DPDK v16.07 (20e2b6eba13d9eb61b23ea75f09f2aa966fa6325 - in DPDK repo)

TG Build Script used

https://gerrit.fd.io/r/gitweb?p=csit.git;a=blob;f=resources/tools/t-rex/t-rex-installer.sh;h=d015015c9275c706d47788cf308aee2a0477231f;hb=refs/heads/rls1609

TG Startup Configuration 

$ cat /etc/trex_cfg.yaml
- port_limit      : 2
  version         : 2
  interfaces      : ["0000:0d:00.0","0000:0d:00.1"]
  port_info       :
          - dest_mac        :   [0x3c,0xfd,0xfe,0x9c,0xee,0xf5]
            src_mac         :   [0x3c,0xfd,0xfe,0x9c,0xee,0xf4]
          - dest_mac        :   [0x3c,0xfd,0xfe,0x9c,0xee,0xf4]
            src_mac         :   [0x3c,0xfd,0xfe,0x9c,0xee,0xf5]

TG common API - pointer to driver

https://gerrit.fd.io/r/gitweb?p=csit.git;a=blob;f=resources/tools/t-rex/t-rex-stateless.py;h=8a7f34b27aaf86d81540d72f05959b409e2134a5;hb=refs/heads/rls1609

Functional Tests - Results

Bridge Domain

Bridge Domain Untagged

  • L2 bridge-domain test cases
  • [Top] Network Topologies: TG=DUT1 2-node topology with two links between nodes; TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes; TG=DUT1=DUT2=TG 3-node circular topology with double parallel links and TG=DUT=VM 3-node topology with VM and double parallel links.
  • [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all links.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge-domain (L2BD) switching combined with static MACs; MAC learning enabled and Split Horizon Groups (SHG) depending on test case.
  • [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: DUT reports active interfaces [Top] TG=DUT1; TG-DUT1-DUT2-TG. [Enc] None. [Cfg] Discovered active interfaces. [Ver] Report active interfaces on DUT. [Ref] PASS
TC02: DUT with L2BD (MAC learning) switch ICMPv4 between two TG links [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two i/fs into L2BD with MAC learning. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 in both directions and are correct on receive. [Ref] PASS
TC03: DUT1 and DUT2 with L2BD (MAC learning) switch between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 and DUT2 configure two i/fs into L2BD with MAC learning. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and DUT2 in both directions and are correct on receive. [Ref] PASS
TC04: DUT1 and DUT2 with L2BD (static MACs) switch between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 and DUT2 configure two i/fs into L2BD with static MACs. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and DUT2 in both directions and are correct on receive. [Ref] PASS
TC05: DUT1 and DUT2 with L2BD (MAC learn) and SHG switch between four TG links [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 and DUT2 configure four i/fs into L2BD with MAC learning and the same SHG on i/fs towards TG. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and DUT2 in both directions and are correct on receive; verify no pkts are switched thru SHG isolated interfaces. [Ref] PASS
TC06: DUT with two L2BDs (MAC learn) switches ICMPv4 between TG and VM links [Top] TG=DUT=VM. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two L2BDs with MAC learning, each with vhost-user i/f to local VM and i/f to TG; configure VM to loop pkts back betwen its two virtio i/fs. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and VM in both directions and are correct on receive. [Ref] PASS
TC07: DUT with two L2BDs (MAC learn) switches ICMPv6 between TG and VM links [Top] TG=DUT=VM. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT1 configure two L2BDs with MAC learning, each with vhost-user i/f to local VM and i/f to TG; configure VM to loop pkts back betwen its two virtio i/fs. [Ver] Make TG verify ICMPv6 Echo Req pkts are switched thru DUT1 and VM in both directions and are correct on receive. [Ref] PASS
TC08: DUT with two L2BDs (static MACs) switches ICMPv4 between TG and VM links [Top] TG=DUT=VM. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two L2BDs with static MACs, each with vhost-user i/f to local VM and i/f to TG; configure VM to loop pkts back betwen its two virtio i/fs. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and VM in both directions and are correct on receive. [Ref] PASS
TC09: DUT with two L2BDs (static MACs) switches ICMPv6 between TG and VM links [Top] TG=DUT=VM. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT1 configure two L2BDs with static MACs, each with vhost-user i/f to local VM and i/f to TG; configure VM to loop pkts back betwen its two virtio i/fs. [Ver] Make TG verify ICMPv6 Echo Req pkts are switched thru DUT1 and VM in both directions and are correct on receive. [Ref] PASS

Cop

Cop Whitelist Blacklist

  • COP Security IPv4 Blacklist and Whitelist Tests
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 on all links.
  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and static routes. COP security white-lists are applied on DUT1 ingress interface from TG. DUT2 is configured with L2XC.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in one direction by TG on link to DUT1; on receive TG verifies packets for correctness and drops as applicable.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: DUT permits IPv4 pkts with COP whitelist set with IPv4 src-addr [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure interface IPv4 addresses and routes in the main routing domain, add COP whitelist on interface to TG with IPv4 src-addr matching packets generated by TG; on DUT2 configure L2 xconnect. [Ver] Make TG send ICMPv4 Echo Req on its interface to DUT1; verify received ICMPv4 Echo Req pkts are correct. [Ref] PASS
TC02: DUT drops IPv4 pkts with COP blacklist set with IPv4 src-addr [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure interface IPv4 addresses and routes in the main routing domain, add COP blacklist on interface to TG with IPv4 src-addr matching packets generated by TG; on DUT2 configure L2 xconnect. [Ver] Make TG send ICMPv4 Echo Req on its interface to DUT1; verify no ICMPv4 Echo Req pkts are received. [Ref] PASS

cop whitelist blacklist IPv6

  • COP Security IPv6 Blacklist and Whitelist Tests
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-ICMPv6 on all links.
  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and static routes. COP security white-lists are applied on DUT1 ingress interface from TG. DUT2 is configured with L2XC.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in one direction by TG on link to DUT1; on receive TG verifies packets for correctness and drops as applicable.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: DUT permits IPv6 pkts with COP whitelist set with IPv6 src-addr [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT1 configure interface IPv6 addresses and routes in the main routing domain, add COP whitelist on interface to TG with IPv6 src-addr matching packets generated by TG; on DUT2 configure L2 xconnect. [Ver] Make TG send ICMPv6 Echo Req on its interface to DUT1; verify received ICMPv6 Echo Req pkts are correct. [Ref] PASS
TC02: DUT drops IPv6 pkts with COP blacklist set with IPv6 src-addr [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT1 configure interface IPv6 addresses and routes in the main routing domain, add COP blacklist on interface to TG with IPv6 src-addr matching packets generated by TG; on DUT2 configure L2 xconnect. [Ver] Make TG send ICMPv6 Echo Req on its interface to DUT1; verify no ICMPv6 Echo Req pkts are received. [Ref] PASS

Dhcp

Dhcp Client

  • DHCP Client related test cases
Name Documentation Status
VPP sends a DHCP DISCOVER Configure DHCP client on interface to TG without hostname and check if DHCP DISCOVER message contains all required fields with expected values. PASS
VPP sends a DHCP DISCOVER with hostname Configure DHCP client on interface to TG with hostname and check if DHCP DISCOVER message contains all required fields with expected values. PASS
VPP sends DHCP REQUEST after OFFER Configure DHCP client on interface to TG and check if DHCP REQUEST message contains all required fields. PASS
VPP honors DHCPv4 lease time Send IP configuration to the VPP client via DHCP. Address is checked with ICMP echo request and there should be no reply for echo request when lease has expired. PASS

Dhcp V4 Proxy

  • DHCP proxy test cases
  • [Top] Network Topologies: TG = DUT with two links between the nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP-BOOTP-DHCP
  • [Cfg] DUT configuration: DUT is configured with DHCP proxy.
  • [Ver] TG verification: Test DHCP packets are sent on TG on first link to DUT and received on TG on second link. On receive TG verifies if DHCP packets are valid.
Name Documentation Status
TC01: VPP proxies valid DHCPv4 request to DHCPv4 server [Top] TG=DUT [Enc] Eth-IPv4-UDP-BOOTP-DHCP [Cfg] On DUT setup DHCP proxy. [Ver] Make TG verify matching DHCP packets between client and DHCP server through DHCP proxy. PASS
TC02: VPP proxy ignores invalid DHCPv4 request [Top] TG=DUT [Enc] Eth-IPv4-UDP-BOOTP-DHCP [Cfg] On DUT setup DHCP proxy. [Ver] Make TG verify matching invalid DHCP packets are dropped. PASS

Dhcp V6 Proxy

  • DHCPv6 proxy test cases
  • [Top] Network Topologies: TG = DUT with two links between the nodes.
  • [Cfg] DUT configuration: DUT is configured with DHCP proxy.
  • [Ver] TG verification:Test DHCP packets are sent on TG on first link to DUT and received on TG on second link. On receive TG verifies if DHCP packets are valid
  • [Ref] Applicable standard specifications: RFC 3315
Name Documentation Status
TC01: VPP proxies valid DHCPv6 request to DHCPv6 server [Top] TG=DUT [Cfg] On DUT setup DHCP proxy. [Ver] Make TG verify matching DHCPv6 packets between client and DHCP server through DHCP proxy. [Ref] RFC 3315 PASS

Gre

Gre Encapsulation

  • GREoIPv4 test cases
  • [Top] Network Topologies: TG=DUT1 2-node topology with two links between nodes; TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-GRE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for routing over GRE tunnel; Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT for GREoIPv4 encapsulation and decapsulation verification.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. GREoIPv4 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; GREoIPv4 encapsulation and decapsulation are verified separately by TG; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC2784.
Name Documentation Status
TC01: DUT1 and DUT2 route over GREoIPv4 tunnel between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-GRE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure GREoIPv4 tunnel with IPv4 routes towards each other. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and GRE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC2784. PASS
TC02: DUT encapsulates IPv4 into GREoIPv4 tunnel - GRE header verification [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT. [Cfg] On DUT1 configure GREoIPv4 tunnel with IPv4 route towards TG. [Ver] Make TG send non-encapsulated ICMPv4 Echo Req to DUT; verify TG received GREoIPv4 encapsulated packet is correct. [Ref] RFC2784. PASS
TC03: DUT decapsulates IPv4 from GREoIPv4 tunnel - IPv4 header verification [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT. [Cfg] On DUT1 configure GREoIPv4 tunnel towards TG. [Ver] Make TG send ICMPv4 Echo Req encapsulated into GREoIPv4 towards VPP; verify TG received IPv4 de-encapsulated packet is correct. [Ref] RFC2784. PASS
TC04: DUT encapsulates IPv4 into GREoIPv4 different tunnels - GRE header verification [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT. [Cfg] On DUT1 configure two GRE tunnels with loopback's source address. Destination address of tunnels are routed via next hop address of DUT's to TG if2, where should be only GRE encapsulated packets. Each tunnel has IPv4 address and configured prefix routed through the tunnel. [Ver] Make TG send non-encapsulated ICMPv4 Echo Req to DUT; verify TG received GREoIPv4 encapsulated packet is correct for each tunnel. [Ref] RFC2784. PASS
TC05: DUT re-encapsulates IPv4 GRE into other GRE tunnel - GRE header verification [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT. [Cfg] On DUT1 configure two GRE tunnels with loopback's source address. Destination address of tunnels are routed via next hop address of DUT's to TG if2, where should be only GRE encapsulated packets. Each tunnel has IPv4 address and configured prefix routed through the tunnel. [Ver] Make TG send encapsulated IPv4 UDP to DUT; Encapsulated IP source is behind configured tunnel same as destination; verify TG received GREoIPv4 encapsulated packet is correct. [Ref] RFC2784. PASS
TC06: DUT do not process GRE with wrong tunnel destination IP [Top] TG=DUT1. [Enc] Eth-IPv4-ICMPv4 on TG_if1-DUT, Eth-IPv4-GRE-IPv4-ICMPv4 on TG_if2_DUT. [Cfg] On DUT1 configure two GRE tunnels with loopback's source address. Destination address of tunnels are routed via next hop address of DUT's to TG if2, where should be only GRE encapsulated packets. On DUT's to TG if1 interface is configured test destination host MAC address. [Ver] Make TG send GRE encapsulated ICMPv4 Echo Req to DUT; verify TG received de-capsulated packet is correct, then send packet with wrong tunnel destination address. [Ref] RFC2784. PASS

Iacl

Ipv4 Iacl Untagged

  • IPv4 routing with ingress ACL test cases Encapsulations: Eth-IPv4 on links TG-DUT1, TG-DUT2, DUT1-DUT2. IPv4 ingress ACL (iACL) tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv4 routing and static routes. DUT1 is configured with iACL on link to TG, iACL classification and permit/deny action are configured on a per test case basis. Test ICMPv4 Echo Request packets are sent in one direction by TG on link to DUT1 and received on TG link to DUT2. On receive TG verifies if packets are dropped, or if received verifies packet IPv4 src-addr, dst-addr and MAC addresses.
Name Documentation Status
TC01: DUT with iACL IPv4 src-addr drops matching pkts On DUT1 add source IPv4 address to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC02: DUT with iACL IPv4 dst-addr drops matching pkts On DUT1 add destination IPv4 address to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC03: DUT with iACL IPv4 src-addr and dst-addr drops matching pkts On DUT1 add source and destination IPv4 addresses to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC04: DUT with iACL IPv4 protocol set to TCP drops matching pkts On DUT1 add protocol mask and TCP protocol (0x06) to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC05: DUT with iACL IPv4 protocol set to UDP drops matching pkts On DUT1 add protocol mask and UDP protocol (0x11) to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC06: DUT with iACL IPv4 TCP src-ports drops matching pkts On DUT1 add TCP source ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC07: DUT with iACL IPv4 TCP dst-ports drops matching pkts On DUT1 add TCP destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC08: DUT with iACL IPv4 TCP src-ports and dst-ports drops matching pkts On DUT1 add TCP source and destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC09: DUT with iACL IPv4 UDP src-ports drops matching pkts On DUT1 add UDP source ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC10: DUT with iACL IPv4 UDP dst-ports drops matching pkts On DUT1 add TCP destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC11: DUT with iACL IPv4 UDP src-ports and dst-ports drops matching pkts On DUT1 add UDP source and destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS

Ipv6 Iacl Untagged

  • IPv6 routing with ingress ACL test cases Encapsulations: Eth-IPv6 on links TG-DUT1, TG-DUT2, DUT1-DUT2. IPv6 ingress ACL (iACL) tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv6 routing and static routes. DUT1 is configured with iACL on link to TG, iACL classification and permit/deny action are configured on a per test case basis. Test ICMPv6 Echo Request packets are sent in one direction by TG on link to DUT1 and received on TG link to DUT2. On receive TG verifies if packets are dropped, or if received verifies packet IPv6 src-addr, dst-addr and MAC addresses.
Name Documentation Status
TC01: DUT with iACL IPv6 src-addr drops matching pkts On DUT1 add source IPv6 address to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC02: DUT with iACL IPv6 dst-addr drops matching pkts On DUT1 add destination IPv6 address to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC03: DUT with iACL IPv6 src-addr and dst-addr drops matching pkts On DUT1 add source and destination IPv6 addresses to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC04: DUT with iACL IPv6 protocol set to TCP drops matching pkts On DUT1 add protocol mask and TCP protocol (0x06) to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC05: DUT with iACL IPv6 protocol set to UDP drops matching pkts On DUT1 add protocol mask and UDP protocol (0x11) to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC06: DUT with iACL IPv6 TCP src-ports drops matching pkts On DUT1 add TCP source ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC07: DUT with iACL IPv6 TCP dst-ports drops matching pkts On DUT1 add TCP destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC08: DUT with iACL IPv6 TCP src-ports and dst-ports drops matching pkts On DUT1 add TCP source and destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC09: DUT with iACL IPv6 UDP src-ports drops matching pkts On DUT1 add UDP source ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC10: DUT with iACL IPv6 UDP dst-ports drops matching pkts On DUT1 add TCP destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC11: DUT with iACL IPv6 UDP src-ports and dst-ports drops matching pkts On DUT1 add UDP source and destination ports to classify table with 'deny'. Make TG verify matching packets are dropped. PASS
TC12: DUT with iACL MAC src-addr and iACL IPv6 UDP src-ports and dst-ports drops matching pkts On DUT1 add source MAC address to classify (L2) table and add UDP source and destination ports to classify (hex) table with 'deny'. Make TG verify matching packets are dropped. PASS

L2 Iacl Untagged

  • Ingress ACL test cases
  • [Top] Network Topologies: TG - DUT1 - DUT2 - TG with one link between the nodes.
  • [Cfg] DUT configuration: DUT2 is configured with L2 Cross connect. DUT1 is configured with iACL classification on link to TG,
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in one direction by TG on link to DUT1 and received on TG link to DUT2. On receive TG verifies if packets are dropped.
Name Documentation Status
TC01: DUT with iACL MAC src-addr drops matching pkts [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 add source MAC address to classify table with 'deny'. [Ver] Make TG verify matching packets are dropped. PASS
TC02: DUT with iACL MAC dst-addr drops matching pkts [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 add destination MAC address to classify table with 'deny'. [Ver] Make TG verify matching packets are dropped. PASS
TC03: DUT with iACL MAC src-addr and dst-addr drops matching pkts [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 add source and destination MAC address to classify table with 'deny'. [Ver] Make TG verify matching packets are dropped. PASS
TC04: DUT with iACL EtherType drops matching pkts [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 add EtherType IPv4(0x0800) to classify table with 'deny'. [Ver] Make TG verify matching packets are dropped. PASS

Ipsec

Ipsec Transport Mode Ipv4

  • IPv4 IPsec transport mode test suite.
  • [Top] Network topologies: TG-DUT1 2-node topology with one link between nodes.
  • [Cfg] DUT configuration: On DUT1 create loopback interface, configure loopback an physical interface IPv4 addresses, static ARP record, route and IPsec manual keyed connection in transport mode.
  • [Ver] TG verification: ESP packet is sent from TG to DUT1. ESP packet is received on TG from DUT1.
  • [Ref] Applicable standard specifications: RFC4303.
Name Documentation Status
TC01: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC05: VPP process ESP packet in Transport Mode with AES-CBC-192 encryption and SHA-256-128 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-192 and integrity algorithm SHA-256-128 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC09: VPP process ESP packet in Transport Mode with AES-CBC-256 encryption and SHA-384-192 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-384-192 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC12: VPP process ESP packet in Transport Mode with AES-CBC-256 encryption and SHA-512-256 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-512-256 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC13: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet encrypted by encryption key different from encryption key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC14: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet authenticated by integrity key different from integrity key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC15: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption and integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet authenticated by integrity key and encrypted by encryption key different from integrity and encryption keys stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS

Ipsec Transport Mode Ipv6

  • IPv6 IPsec transport mode test suite.
  • [Top] Network topologies: TG-DUT1 2-node topology with one link between nodes.
  • [Cfg] DUT configuration: On DUT1 create loopback interface, configure loopback an physical interface IPv6 addresses, static ARP record, route and IPsec manual keyed connection in transport mode.
  • [Ver] TG verification: ESP packet is sent from TG to DUT1. ESP packet is received on TG from DUT1.
  • [Ref] Applicable standard specifications: RFC4303.
Name Documentation Status
TC01: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC05: VPP process ESP packet in Transport Mode with AES-CBC-192 encryption and SHA-256-128 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-192 and integrity algorithm SHA-256-128 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC09: VPP process ESP packet in Transport Mode with AES-CBC-256 encryption and SHA-384-192 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-384-192 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC12: VPP process ESP packet in Transport Mode with AES-CBC-256 encryption and SHA-512-256 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-512-256 in transport mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC13: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet encrypted by encryption key different from encryption key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC14: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet authenticated by integrity key different from integrity key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC15: VPP process ESP packet in Transport Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption and integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in transport mode. [Ver] Send an ESP packet authenticated by integrity key and encrypted by encryption key different from integrity and encryption keys stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS

Ipsec Tunnel Mode Ipv4

  • IPv4 IPsec tunnel mode test suite.
  • [Top] Network topologies: TG-DUT1 2-node topology with one link between nodes.
  • [Cfg] DUT configuration: On DUT1 create loopback interface, configure loopback an physical interface IPv4 addresses, static ARP record, route and IPsec manual keyed connection in tunnel mode.
  • [Ver] TG verification: ESP packet is sent from TG to DUT1. ESP packet is received on TG from DUT1.
  • [Ref] Applicable standard specifications: RFC4303.
Name Documentation Status
TC01: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC05: VPP process ESP packet in Tunnel Mode with AES-CBC-192 encryption and SHA-256-128 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-192 and integrity algorithm SHA-256-128 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC09: VPP process ESP packet in Tunnel Mode with AES-CBC-256 encryption and SHA-384-192 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-384-192 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC12: VPP process ESP packet in Tunnel Mode with AES-CBC-256 encryption and SHA-512-256 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-512-256 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC13: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet encrypted by encryption key different from encryption key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC14: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet authenticated by integrity key different from integrity key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC15: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption and integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet authenticated by integrity key and encrypted by encryption key different from integrity and encryption keys stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS

Ipsec Tunnel Mode Ipv6

  • IPv6 IPsec tunnel mode test suite.
  • [Top] Network topologies: TG-DUT1 2-node topology with one link between nodes.
  • [Cfg] DUT configuration: On DUT1 create loopback interface, configure loopback an physical interface IPv6 addresses, static ARP record, route and IPsec manual keyed connection in tunnel mode.
  • [Ver] TG verification: ESP packet is sent from TG to DUT1. ESP packet is received on TG from DUT1.
  • [Ref] Applicable standard specifications: RFC4303.
Name Documentation Status
TC01: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC05: VPP process ESP packet in Tunnel Mode with AES-CBC-192 encryption and SHA-256-128 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-192 and integrity algorithm SHA-256-128 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC09: VPP process ESP packet in Tunnel Mode with AES-CBC-256 encryption and SHA-384-192 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-384-192 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC12: VPP process ESP packet in Tunnel Mode with AES-CBC-256 encryption and SHA-512-256 integrity [Top] TG-DUT1. [Ref] RFC4303. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-256 and integrity algorithm SHA-512-256 in tunnel mode. [Ver] Send and receive ESP packet between TG and VPP node. PASS
TC13: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet encrypted by encryption key different from encryption key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC14: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet authenticated by integrity key different from integrity key stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS
TC15: VPP process ESP packet in Tunnel Mode with AES-CBC-128 encryption and SHA1-96 integrity - different encryption and integrity alogrithms used [Top] TG-DUT1. [Cfg] On DUT1 configure IPsec manual keyed connection with encryption algorithm AES-CBC-128 and integrity algorithm SHA1-96 in tunnel mode. [Ver] Send an ESP packet authenticated by integrity key and encrypted by encryption key different from integrity and encryption keys stored on VPP node from TG to VPP node and expect no response to be received on TG. [Ref] RFC4303. PASS

Ipv4

Ipv4 Arp Untagged

  • IPv4 ARP test cases RFC826 ARP: Eth-IPv4 and Eth-ARP on links TG-DUT1, TG-DUT2, DUT1-DUT2: IPv4 ARP tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv4 routing and static routes. DUT ARP functionality is tested by making TG send ICMPv4 Echo Requests towards its other interface via DUT1 and DUT2.
Name Documentation Status
TC01: DUT sends ARP Request for unresolved locally connected IPv4 address Make TG send test packet destined to IPv4 address of its other interface connected to DUT2. Make TG verify DUT2 sends ARP Request for locally connected TG IPv4 address. PASS
TC02: DUT sends ARP Request for route next hop IPv4 address Make TG send test packet destined to IPv4 address matching static route on DUT2. Make TG verify DUT2 sends ARP Request for next hop of the static route. PASS

Ipv4 Proxy Arp Untagged

  • RFC1027 Proxy ARP test cases
  • [Top] Network topologies: TG-DUT1 2-node topology with single link between nodes.
  • [Cfg] DUT configuration: DUT1 is configured with Proxy ARP
  • [Ver] TG verification: Test ARP Request packet is sent from TG on link to DUT1; on receive TG verifies ARP reply packet for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC1027.
Name Documentation Status
TC01: DUT sends ARP reply on behalf of another machine from the IP range [Top] TG-DUT1. [Ref] RFC1027. [Cfg] On DUT1 configure interface IPv4 address and proxy ARP for IP range. [Ver] Make TG send ARP request to DUT1 interface, verify if DUT1 sends correct ARP reply on behalf of machine which IP is in range. PASS
TC02: DUT sends ARP reply on behalf of another machine from beginning of the IP range [Top] TG-DUT1. [Ref] RFC1027. [Cfg] On DUT1 configure interface IPv4 address and proxy ARP for IP range. [Ver] Make TG send ARP request to DUT1 interface, verify if DUT1 sends correct ARP reply on behalf of machine which IP is from beginning of the IP range. PASS
TC03: DUT sends ARP reply on behalf of another machine from end of the IP range [Top] TG-DUT1. [Ref] RFC1027. [Cfg] On DUT1 configure interface IPv4 address and proxy ARP for IP range. [Ver] Make TG send ARP request to DUT1 interface, verify if DUT1 sends correct ARP reply on behalf of machine which IP is from end of the IP range. PASS
TC04: DUT does not send ARP reply on behalf of another machine from below of the IP range [Top] TG-DUT1. [Ref] RFC1027. [Cfg] On DUT1 configure interface IPv4 address and proxy ARP for IP range. [Ver] Make TG send ARP request to DUT1 interface, verify if DUT1 does not send ARP reply on behalf of machine which IP is from below of the IP range. PASS
TC05: DUT does not send ARP reply on behalf of another machine from above of the IP range [Top] TG-DUT1. [Ref] RFC1027. [Cfg] On DUT1 configure interface IPv4 address and proxy ARP for IP range. [Ver] Make TG send ARP request to DUT1 interface, verify if DUT1 does not send ARP reply on behalf of machine which IP is from above of the IP range. PASS

Ipv4 Untagged

  • IPv4 routing test cases RFC791 IPv4, RFC826 ARP, RFC792 ICMPv4. Encapsulations: Eth-IPv4-ICMPv4 on links TG-DUT1, TG-DUT2, DUT1-DUT2. IPv4 routing tests use circular 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv4 routing and static routes. Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2 and received on TG links on the other side of circular topology. On receive TG verifies packets IPv4 src-addr, dst-addr and MAC addresses.
Name Documentation Status
TC01: DUT replies to ICMPv4 Echo Req to its ingress interface Make TG send ICMPv4 Echo Req to DUT ingress interface. Make TG verify ICMP Echo Reply is correct. PASS
TC02: DUT routes IPv4 to its egress interface Make TG send ICMPv4 Echo Req towards DUT1 egress interface connected to DUT2. Make TG verify ICMPv4 Echo Reply is correct. PASS
TC03: DUT1 routes IPv4 to DUT2 ingress interface Make TG send ICMPv4 Echo Req towards DUT2 ingress interface connected to DUT1. Make TG verify ICMPv4 Echo Reply is correct. PASS
TC04: DUT1 routes IPv4 to DUT2 egress interface Make TG send ICMPv4 Echo Req towards DUT2 egress interface connected to TG. Make TG verify ICMPv4 Echo Reply is correct. PASS
TC05: DUT1 and DUT2 route IPv4 between TG interfaces Make TG send ICMPv4 Echo Req between its interfaces across DUT1 and DUT2. Make TG verify ICMPv4 Echo Replies are correct. PASS
TC06: DUT replies to ICMPv4 Echo Reqs with size 64B-to-1500B-incr-1B Make TG send ICMPv4 Echo Reqs to DUT ingress interface, incrementating frame size from 64B to 1500B with increment step of 1Byte. Make TG verify ICMP Echo Replies are correct. PASS
TC08: DUT replies to ARP request Make TG send ARP Request to DUT and verify ARP Reply is correct. PASS

Ipv6

Ipv6 Ra

  • IPv6 Router Advertisement test cases RFC4861 Neighbor Discovery. Encapsulations: Eth-IPv6-RA on links TG-DUT1. IPv6 Router Advertisement tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv6 routing and static routes. TG verifies received RA packets.
Name Documentation Status
TC01: DUT transmits RA on IPv6 enabled interface [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPv6 interface on the link to TG. [Ver] Make TG wait for IPv6 Router Advertisement packet to be sent by DUT1 and verify the received RA packet is correct. PASS
TC02: DUT retransmits RA on IPv6 enabled interface after a set interval [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPv6 interface on the link to TG. [Ver] Make TG wait for two IPv6 Router Advertisement packets to be sent by DUT1 and verify the received RA packets are correct. PASS

Ipv6 Untagged

  • IPv6 routing test cases RFC2460 IPv6, RFC4443 ICMPv6, RFC4861 Neighbor Discovery. Encapsulations: Eth-IPv6-ICMPv6 on links TG-DUT1, TG-DUT2, DUT1-DUT2; Eth-IPv6-NS/NA on links TG-DUT. IPv6 routing tests use circular 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 and DUT2 are configured with IPv6 routing and static routes. Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2 and received on TG links on the other side of circular topology. On receive TG verifies packets IPv6 src-addr, dst-addr and MAC addresses.
Name Documentation Status
TC01: DUT replies to ICMPv6 Echo Req to its ingress interface Make TG send ICMPv6 Echo Req to DUT ingress interface. Make TG verify ICMPv6 Echo Reply is correct. PASS
TC02: DUT replies to ICMPv6 Echo Req pkt with size 64B-to-1500B-incr-1B Make TG send ICMPv6 Echo Reqs to DUT ingress interface, incrementating frame size from 64B to 1500B with increment step of 1Byte. Make TG verify ICMP Echo Replies are correct. PASS
TC04: DUT routes to its egress interface Make TG send ICMPv6 Echo Req towards DUT1 egress interface connected to DUT2. Make TG verify ICMPv6 Echo Reply is correct. PASS
TC05: DUT1 routes to DUT2 ingress interface Make TG send ICMPv6 Echo Req towards DUT2 ingress interface connected to DUT1. Make TG verify ICMPv6 Echo Reply is correct. PASS
TC06: DUT1 routes to DUT2 egress interface Make TG send ICMPv6 Echo Req towards DUT2 egress interface connected to TG. Make TG verify ICMPv6 Echo Reply is correct. PASS
TC07: DUT1 and DUT2 route between TG interfaces Make TG send ICMPv6 Echo Req between its interfaces across DUT1 and DUT2. Make TG verify ICMPv6 Echo Replies are correct. PASS
TC08: DUT replies to IPv6 Neighbor Solicitation On DUT configure interface IPv6 address in the main routing domain. Make TG send Neighbor Solicitation message on the link to DUT and verify DUT Neighbor Advertisement reply is correct. PASS

L2 Xconnect

L2 Xconnect Untagged

  • L2 cross-connect test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes; TG=DUT1=DUT2=TG 3-node circular topology with double parallel links and TG=DUT=VM 3-node topology with VM and double parallel links.
  • [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all links.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross-connect (L2XC) switching.
  • [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: DUT1 and DUT2 with L2XC switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 and DUT2 configure L2 cross-connect (L2XC), each with one interface to TG and one Ethernet interface towards the other DUT. [Ver] Make TG send ICMPv4 Echo Req in both directions between two of its interfaces to be switched by DUT1 and DUT2; verify all packets are received. [Ref] PASS
TC02: DUT1 and DUT2 with L2XC switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT1 and DUT2 configure L2 cross-connect (L2XC), each with one interface to TG and one Ethernet interface towards the other DUT. [Ver] Make TG send ICMPv6 Echo Req in both directions between two of its interfaces to be switched by DUT1 and DUT2; verify all packets are received. [Ref] PASS
TC03: DUT with two L2XCs switches ICMPv4 between TG and local VM links [Top] TG=DUT=VM. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT configure two L2 cross-connects (L2XC), each with one untagged interface to TG and untagged i/f to local VM over vhost-user. [Ver] Make TG send ICMPv4 Echo Reqs in both directions between two of its i/fs to be switched by DUT to and from VM; verify all packets are received. [Ref] PASS
TC04: DUT with two L2XCs switches ICMPv6 between TG and local VM links [Top] TG=DUT=VM. [Enc] Eth-IPv6-ICMPv6. [Cfg] On DUT configure two L2 cross-connects (L2XC), each with one untagged i/f to TG and untagged i/f to local VM over vhost-user. [Ver] Make TG send ICMPv6 Echo Reqs in both directions between two of its i/fs to be switched by DUT to and from VM; verify all packets are received. [Ref] PASS

Lisp

Lisp Api Untagged

  • LISP API test cases
  • [Top] Network Topologies: DUT1 1-node topology.
  • [Enc] Packet Encapsulations: None.
  • [Cfg] DUT configuration: DUT1 gets configured with all LISP parameters.
  • [Ver] Verification: DUT1 operational data gets verified following configuration.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
TC01: DUT can enable and disable LISP [Top] DUT1. [Enc] None. [Cfg1] Test LISP enable/disable API; On DUT1 enable LISP. [Ver1] Check DUT1 if LISP is enabled. [Cfg2] Then disable LISP. [Ver2] Check DUT1 if LISP is disabled. [Ref] RFC6830. PASS
TC02: DUT can add and delete locator_set [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on DUT1 configure locator_set and locator. [Ver1] Check DUT1 configured locator_set and locator are correct. [Cfg2] Then remove locator_set and locator. [Ver2] check DUT1 locator_set and locator are removed. [Ref] RFC6830. PASS
TC04: DUT can add and delete eid address [Top] DUT1. [Enc] None. [Cfg1] Test LISP eid API; on DUT1 configure LISP eid IP address. [Ver1] Check DUT1 configured data is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all eid IP addresses are removed. [Ref] RFC6830. PASS
TC05: DUT can add and delete LISP map resolver address [Top] DUT1. [Enc] None. [Cfg1] Test LISP map resolver address API; on DUT1 configure LISP map resolver address. [Ver1] Check DUT1 configured data is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all map resolver addresses are removed. [Ref] RFC6830. PASS

Lisp Dataplane Untagged

  • LISP static adjacency test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 (IPv6) routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISPoIPv4 tunnel [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. PASS
TC02: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv6 tunnel [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv6 LISP static adjacencies. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. PASS
TC03: DUT1 and DUT2 route IPv4 bidirectionally over LISPoIPv6 tunnel [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv6 LISP static adjacencies. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. PASS
TC04: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv4 tunnel [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. PASS
TC05: DUT1 and DUT2 route IPv4 over LISPoIPv4 tunnel after disable-enable [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg1] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. [Ver1] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Disable LISP. [Ver2] Verify packets are not received via LISP tunnel. [Cfg3] Re-enable LISP. [Ver3] Verify packets are received again via LISP tunnel. [Ref] RFC6830. PASS

Lisp Ipv4 Lispgpe Ipv4

  • ip4-lispgpe-ip4 encapsulation test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces Case: ip4-lispgpe-ip4 - phy2lisp [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830. PASS
TC02: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled Case: ip4-lispgpe-ip4 - vrf, phy2lisp [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830. PASS

Policer

Policer Ip4

  • IPv4 policer test cases
  • [Top] Network topologies: TG=DUT1 2-node topology with two links between nodes.
  • [Cfg] DUT configuration: On DUT1 configure interfaces IPv4 adresses, and static ARP record on the second interface.
  • [Ver] TG verification: Test packet is sent from TG on the first link to DUT1. Packet is received on TG on the second link from DUT1.
  • [Ref] Applicable standard specifications: RFC2474, RFC2697, RFC2698.
Name Documentation Status
TC01: VPP policer 2R3C Color-aware marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2698. [Cfg] On DUT1 configure 2R3C color-aware policer on the first interface. [Ver] TG sends IPv4 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv4 TCP packet with correct DSCP on the second link to TG. PASS
TC02: VPP policer 2R3C Color-blind marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2698. [Cfg] On DUT1 configure 2R3C color-blind policer on the first interface. [Ver] TG sends IPv4 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv4 TCP packet with correct DSCP on the second link to TG. PASS
TC03: VPP policer 1R3C Color-aware marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2697. [Cfg] On DUT1 configure 1R3C color-aware policer on the first interface. [Ver] TG sends IPv4 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv4 TCP packet with correct DSCP on the second link to TG. PASS
TC04: VPP policer 1R3C Color-blind marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2697. [Cfg] On DUT1 configure 1R3C color-blind policer on the first interface. [Ver] TG sends IPv4 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv4 TCP packet with correct DSCP on the second link to TG. PASS

Policer Ip6

  • IPv6 policer test cases
  • [Top] Network topologies: TG=DUT1 2-node topology with two links between nodes.
  • [Cfg] DUT configuration: On DUT1 configure interfaces IPv6 adresses, and static neighbor record on the second interface.
  • [Ver] TG verification: Test packet is sent from TG on the first link to DUT1. Packet is received on TG on the second link from DUT1.
  • [Ref] Applicable standard specifications: RFC2474, RFC2697, RFC2698.
Name Documentation Status
TC01: VPP policer 2R3C Color-aware marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2698. [Cfg] On DUT1 configure 2R3C color-aware policer on the first interface. [Ver] TG sends IPv6 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv6 TCP packet with correct DSCP on the second link to TG. PASS
TC02: VPP policer 2R3C Color-blind marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2698. [Cfg] On DUT1 configure 2R3C color-blind policer on the first interface. [Ver] TG sends IPv6 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv6 TCP packet with correct DSCP on the second link to TG. PASS
TC03: VPP policer 1R3C Color-aware marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2697. [Cfg] On DUT1 configure 1R3C color-aware policer on the first interface. [Ver] TG sends IPv6 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv6 TCP packet with correct DSCP on the second link to TG. PASS
TC04: VPP policer 1R3C Color-blind marks packet [Top] TG=DUT1. [Ref] RFC2474, RFC2697. [Cfg] On DUT1 configure 1R3C color-blind policer on the first interface. [Ver] TG sends IPv6 TCP packet on the first link to DUT1, verify if DUT1 sends correct IPv6 TCP packet with correct DSCP on the second link to TG. PASS

Rpf

Ipv4 Rpf Untagged

  • Source RPF check on IPv4 test cases
  • [Top] Network Topologies: TG - DUT1 - DUT2 - TG with one link between the nodes.
  • [Cfg] DUT configuration: DUT2 is configured with L2 Cross connect. DUT1 is configured with IP source check on link to TG,
  • [Ver] TG verification:Test ICMP Echo Request packets are sent in one direction by TG on link to DUT1 and received on TG link to DUT2. On receive TG verifies if packets which source address is not in routes are dropped.
Name Documentation Status
TC01: VPP source RPF check on IPv4 src-addr [Top] TG-DUT1-DUT2-TG [Cfg] On DUT1 setup IP source check. [Ver] Make TG verify matching packets which source address is not in routes are dropped. PASS
TC02: VPP pass traffic on non-enabled RPF interface [Top] TG-DUT1-DUT2-TG [Cfg] On DUT1 setup IP source check. [Ver] Make TG verify matching packets on non-enabled RPF interface are passed. PASS

Softwire

Lightweight 4Over6

  • Lightweight 4 over 6 test cases LW4o6 is a subset of MAP-E, with per-subscriber rules. It uses the same tunneling mechanism and configuration as MAP-E. It does not use embedded address bits.
  • [Top] Network Topologies: TG=DUT1 2-node topology with two links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP on TG_if1-DUT, Eth-IPv6-IPv4-UDP on TG_if2_DUT.
  • [Cfg] DUT configuration: DUT1 is configured as lwAFTR.
  • [Ver] TG verification: Test UDP ICMP Echo Request in IPv4 are sent to lwAFTR and are verified by TG for correctness their encapsulation in IPv6 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC7596 RFC7597.
Name Documentation Status
TC01: Encapsulate IPv4 into IPv6. IPv6 dst depends on IPv4 and UDP destination [Top] TG=DUT1. [Enc] Eth-IPv4-UDP on TG_if1-DUT, Eth-IPv6-IPv4-UDP on TG_if2_DUT. [Cfg] On DUT1 configure Map domain and Map rule. [Ver] Make TG send non-encapsulated UDP to DUT; verify TG received IPv4oIPv6 encapsulated packet is correct. [Ref] RFC7596 RFC7597 PASS
TC02: Encapsulate IPv4 ICMP into IPv6. IPv6 dst depends on IPv4 addr and ICMP ID [Top] TG=DUT1. [Enc] Eth-IPv4-ICMP(type 0 and 8) on TG_if1-DUT, Eth-IPv6-IPv4-ICMP on TG_if2_DUT. [Cfg] On DUT1 configure Map domain and Map rule. [Ver] Make TG send non-encapsulated ICMP to DUT; verify TG received IPv4oIPv6 encapsulated packet is correct. Checks IPv6 destination based on ICMP Identifier field. [Ref] RFC7596 section 8.1 PASS
TC03: Decapsulate IPv4 UDP from IPv6. [Top] TG=DUT1. [Enc] Eth-IPv6-IPv4-UDP on TG_if2_DUT, Eth-IPv4-UDP on TG_if1-DUT. [Cfg] On DUT1 configure Map domain and Map rule. [Ver] Make TG send encapsulated UDP to DUT; verify TG received IPv4 non-encapsulated packet is correct. [Ref] RFC7596 RFC7597 PASS
TC04: Hairpinning of traffic between two lwB4 [Top] DUT1-TG. [Enc] Eth-IPv6-IPv4-UDP on TG_if2_DUT, Eth-IPv6-IPv4-UDP on TG_if2_DUT. [Cfg] On DUT1 configure Map domain and two Map rules. [Ver] Make TG send encapsulated UDP to DUT; verify TG received encapsulated packet is correct. [Ref] RFC7596 RFC7597 PASS

Tap

Tap Interface

  • Tap Interface Traffic Tests
  • [Top] Network Topologies: TG=DUT1 2-node topology with two links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge-domain (L2BD) MAC learning enabled; Split Horizon Groups (SHG) are set depending on test case; Namespaces (NM) are set on DUT1 with attached linux-TAP.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent by TG on link to DUT1; On receipt TG verifies packets for correctness and their IPv4 src-addr, dst-addr, and MAC addresses.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: Tap Interface Simple BD [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two L2BD with two if's for each L2BD with MAC learning and one L2BD joining two linux-TAP interfaces created by VPP located in namespace. [Ver] Packet sent from TG is passed through all L2BD and received back on TG. Then src_ip, dst_ip and MAC are checked. PASS
TC02: Tap Interface IP Ping Without Namespace [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two interface addresses with IPv4 of which one is TAP interface ( dut_to_tg_if and TAP ). and one is linux-TAP. [Ver] Packet sent from TG gets to the destination and ICMP-reply is received on TG. PASS
TC03: Tap Interface IP Ping With Namespace [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure two interface addresses with IPv4 of which one is TAP interface ( dut_to_tg_if and TAP ). and one is linux-TAP in namespace. [Ver] Packet sent from TG gets to the destination and ICMP-reply is received on TG. PASS
TC04: Tap Interface BD - Different Split Horizon [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure one if into L2BD with MAC learning. Add two TAP interfaces into this L2BD and assign them different SHG. Setup two namespaces and assign two linux-TAP interfaces to it respectively. [Ver] Packet is sent from TG to both linux-TAP interfaces and reply is checked. Ping from First linux-TAP to another should pass. PASS
TC05: Tap Interface BD - Same Split Horizon [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] On DUT1 configure one if into L2BD with MAC learning. Add two TAP interfaces into this L2BD and assign them same SHG. Setup two namespaces and assign two linux-TAP interfaces to it respectively. [Ver] Packet is sent from TG to both linux-TAP interfaces and reply is checked. Ping from First linux-TAP to another should fail. PASS
TC06: Tap Interface Modify And Delete [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4. [Cfg] Set two TAP interfaces. [Ver] Verify that TAP interface can be modified, deleted, and no other TAP interface is affected. PASS

Vlan

Qinq L2 Xconnect

  • L2 cross-connect with QinQ test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross-connect (L2XC) switching with 802.1ad QinQ VLAN tag push and pop.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1ad.
Name Documentation Status
TC01: DUT1 and DUT2 with L2XC and two VLAN push-pop switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure L2 cross-connect (L2XC), each with one interface to TG and one Ethernet interface towards the other DUT; each DUT pushes two VLAN tags on packets received from local TG, and popping two VLAN tags on packets transmitted to local TG. [Ver] Make TG send ICMPv4 Echo Req in both directions between two of its interfaces to be switched by DUT1 and DUT2; verify all packets are received. [Ref] IEEE 802.1ad. PASS

Vlan Tag Translate L2 Bridge Domain Ipv4

  • L2 bridge domain with VLAN tag rewrite test cases - IPv4
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1q-IPv4-ICMPv4 or Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with bridge domain (L2BD) switching combined with MAC learning enabled and added VLAN sub-interface with VLAN tag rewrite translate-1-1 method of interface towards TG and interface towards DUT2. DUT2 is configured with L2 bridge domain (L2BD) switching between VLAN sub-interface with VLAN tag rewrite pop-1 method of interface towards DUT1 and interface towards TG.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent from TG on link to DUT1 and received in TG on link form DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1q, IEEE 802.1ad.
Name Documentation Status
TC01: DUT1 and DUT2 with L2BD and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-1 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q PASS
TC03: DUT1 and DUT2 with L2BD and VLAN translate-1-2 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-2 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC07: DUT1 and DUT2 with L2BD and VLAN translate-2-1 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1, Eth-dot1q-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-1 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req tagged with Dot1ad tags from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC09: DUT1 and DUT2 with L2BD and VLAN translate-2-2 switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-2 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 tagged with Dot1ad tags from one of its interfaces to another one method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1ad PASS

Vlan Tag Translate L2 Bridge Domain Ipv6

  • L2 bridge domain with VLAN tag rewrite test cases - IPv6
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1q-IPv6-ICMPv6 or Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2 for L2 switching of IPv6.
  • [Cfg] DUT configuration: DUT1 is configured with bridge domain (L2BD) switching combined with MAC learning enabled and added VLAN sub-interface with VLAN tag rewrite translate-1-1 method of interface towards TG and interface towards DUT2. DUT2 is configured with L2 bridge domain (L2BD) switching between VLAN sub-interface with VLAN tag rewrite pop-1 method of interface towards DUT1 and interface towards TG.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent from TG on link to DUT1 and received in TG on link form DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1q, IEEE 802.1ad.
Name Documentation Status
TC01: DUT1 and DUT2 with L2BD and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-1 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv6 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q PASS
TC03: DUT1 and DUT2 with L2BD and VLAN translate-1-2 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-2 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC07: DUT1 and DUT2 with L2BD and VLAN translate-2-1 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1, Eth-dot1q-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-1 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv6 Echo Req tagged with Dot1ad tags from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC09: DUT1 and DUT2 with L2BD and VLAN translate-2-2 switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1 and on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 bridge domain (L2BD) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-2 method; on DUT2 configure L2 bridge domain (L2BD) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 tagged with Dot1ad tags from one of its interfaces to another one method. [Ver] Make TG send ICMPv6 Echo Req via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1ad PASS

Vlan Tag Translate L2 Xconnect Ipv4

  • L2 cross-connect with VLAN tag rewrite test cases - IPv4
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1q-IPv4-ICMPv4 or Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with L2 cross-connect (L2XC) switching between VLAN sub-interface with VLAN tag rewrite translate-1-1 method of interface towards TG and interface towards DUT2. DUT2 is configured configured with L2 cross-connect (L2XC) switching between VLAN sub-interface with VLAN tag rewrite pop-1 method of interface towards DUT1 and interface towards TG.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent from TG on link to DUT1 and received in TG on link form DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1q, IEEE 802.1ad.
Name Documentation Status
TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-1 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q PASS
TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-2 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-2 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC07: DUT1 and DUT2 with L2XC and VLAN translate-2-1 (DUT1) switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1, Eth-dot1q-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-1 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req tagged with Dot1ad tags from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC09: DUT1 and DUT2 with L2XC and VLAN translate-2-2 switch ICMPv4 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-2 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 tagged with Dot1ad tags from one of its interfaces to another one method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1ad PASS

Vlan Tag Translate L2 Xconnect Ipv6

  • L2 cross-connect with VLAN tag rewrite test cases - IPv6
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1q-IPv6-ICMPv6 or Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2 for L2 switching of IPv6.
  • [Cfg] DUT configuration: DUT1 is configured with L2 cross-connect (L2XC) switching between VLAN sub-interface with VLAN tag rewrite translate-1-1 method of interface towards TG and interface towards DUT2. DUT2 is configured configured with L2 cross-connect (L2XC) switching between VLAN sub-interface with VLAN tag rewrite pop-1 method of interface towards DUT1 and interface towards TG.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent from TG on link to DUT1 and received in TG on link form DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1q, IEEE 802.1ad.
Name Documentation Status
TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-1 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q PASS
TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-2 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1, Eth-dot1ad-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite translate-1-2 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC07: DUT1 and DUT2 with L2XC and VLAN translate-2-1 (DUT1) switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1, Eth-dot1q-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-1 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv6 Echo Req tagegd with Dot1ad tags from one of its interfaces to another one via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1q, IEEE 802.1ad PASS
TC09: DUT1 and DUT2 with L2XC and VLAN translate-2-2 switch ICMPv6 between two TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv6-ICMPv6 on TG-DUT1 and on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite translate-2-2 method; on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 tagegd with Dot1ad tags from one of its interfaces to another one method. [Ver] Make TG send ICMPv6 Echo Req via DUT1 and DUT2; verify that packet is received. [Ref] IEEE 802.1ad PASS

Vrf

Vrf Tests

  • Vpn routed forwarding - baseline IPv4
  • [Top] Network Topologies: TG=DUT1=DUT2=TG 3-node topology with two links in between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration:Each DUT is configured with two VRF tables; Separation of traffic is tested by IP packets; Basic ARP and ROUTES are set on DUT nodes; IP addresses are set on DUT interfaces.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent by TG on link to DUT1, DUT2 or back to TG; On receipt TG verifies packets for correctness and their IPv4 src-addr, dst-addr, and MAC addresses.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: TG packets routed to DUT ingress interface, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv4-ICMPv4. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. On every ingress and egress port on DUT is configured ARP and each DUT is configured with one route. [Ver] Packet is send from TG->DUT1-if1 to DUT1->TG-if1 and from TG->DUT1-if2 to DUT1->TG-if2 and checked if arrived. PASS
TC02: TG packets routed to DUT egress interface, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv4-ICMPv4. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. On every ingress and egress port on DUT is configured ARP and each DUT is configured with one route. [Ver] Packet is send from TG->DUT1-if1 to DUT1->DUT2-if1 and from TG->DUT1-if2 to DUT1->DUT2-if2 and checked if arrived. PASS
TC03: TG packets routed to DUT2 ingress interface through DUT1, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv4-ICMPv4. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. On every ingress and egress port on DUT is configured ARP and each DUT is configured with one route. [Ver] Packet is send from TG->DUT1-if1 to DUT2->DUT1-if1 and from TG->DUT1-if2 to DUT2->DUT1-if2 and checked if arrived. PASS
TC04: TG packets routed to DUT2 egress interface through DUT1, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv4-ICMPv4. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. On every ingress and egress port on DUT is configured ARP and each DUT is configured with one route. [Ver] Packet is send from TG->DUT1-if1 to DUT2->TG-if1 and from TG->DUT1-if2 to DUT2->TG-if2 and checked if arrived. PASS
TC05: TG packets routed to TG through DUT1 and DUT2, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv4-ICMPv4. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. On every ingress and egress port on DUT is configured ARP and each DUT is configured with one route. [Ver] Packet is send from TG->DUT1-if1 to TG->DUT2-if1 and from TG->DUT1-if2 to TG->DUT2-if2 and checked if arrived. PASS

Vrf Tests V6

  • Vpn routed forwarding - baseline IPv6
  • [Top] Network Topologies: TG=DUT1=DUT2=TG 3-node topology with two links in between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-ICMPv6
  • [Cfg] DUT configuration: Each DUT is configured with two VRF tables; Separation of traffic is tested by IP packets; Neighbors and Routes are set on DUT nodes; IP addresses are set on DUT interfaces.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent by TG on link to DUT1, DUT2 or back to TG; On receipt TG verifies packets for correctness and their IPv6 src-addr, dst-addr, and MAC addresses.
  • [Ref] Applicable standard specifications:
Name Documentation Status
TC01: TG packets routed to DUT ingress interface, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv6-ICMPv6. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. Neighbors are configured for each DUTs ingress/egress ports, and each VRF is configured with just one route. [Ver] Packet is sent from TG->DUT1-if1 to DUT1->TG-if1 and from TG->DUT1-if2 to DUT1->TG-if2 and checked if arrived. PASS
TC02: TG packets routed to DUT egress interface, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv6-ICMPv6. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. Neighbors are configured for each DUTs ingress/egress ports, and each VRF is configured with just one route. [Ver] Packet is sent from TG->DUT1-if1 to DUT1->DUT2-if1 and from TG->DUT1-if2 to DUT1->DUT2-if2 and checked if arrived. PASS
TC03: TG packets routed to DUT2 ingress interface through DUT1, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv6-ICMPv6. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. Neighbors are configured for each DUTs ingress/egress ports, and each VRF is configured with just one route. [Ver] Packet is sent from TG->DUT1-if1 to DUT2->DUT1-if1 and from TG->DUT1-if2 to DUT2->DUT1-if2 and checked if arrived. PASS
TC04: TG packets routed to DUT2 egress interface through DUT1, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv6-ICMPv6. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. Neighbors are configured for each DUTs ingress/egress ports, and each VRF is configured with just one route. [Ver] Packet is sent from TG->DUT1-if1 to DUT2->TG-if1 and from TG->DUT1-if2 to DUT2->TG-if2 and checked if arrived. PASS
TC05: TG packets routed to TG through DUT1 and DUT2, VPP configured with two VRFs [Top] TG=DUT1=DUT2=TG [Enc] Eth-IPv6-ICMPv6. [Cfg] DUT1 and DUT2 are both configured with two fib tables. Each table is assigned to 2 interfaces to separate the traffic. Interfaces are configured with IP addresses from *Variables*. Neighbors are configured for each DUTs ingress/egress ports, and each VRF is configured with just one route. [Ver] Packet is sent from TG->DUT1-if1 to TG->DUT2-if1 and from TG->DUT1-if2 to TG->DUT2-if2 and checked if arrived. PASS

Vxlan

Vxlan Bd Dot1Q

  • RFC7348 VXLAN: Bridge-domain with VXLAN over VLAN test cases
  • [Top] Network topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1q-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2, Eth-dot1q-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge-domain (L2BD) switching combined with static MACs, MAC learning enabled and Split Horizon Groups (SHG) depending on test case; VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC7348.
Name Documentation Status
TC01: DUT1 and DUT2 with L2BD and VXLANoIPv4oVLAN tunnels switch ICMPv4 between TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure L2 bridge-domain (MAC learning enabled), each with one interface to TG and one VXLAN tunnel interface towards the other DUT over VLAN sub-interface. [Ver] Make TG send ICMPv4 Echo Req between two of its interfaces, verify all packets are received. [Ref] RFC7348. PASS

Vxlan Bd Untagged

  • RFC7348 VXLAN: Bridge-domain with VXLAN test cases
  • [Top] Network topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes; TG=DUT1=DUT2=TG 3-node circular topology with double parallel links.
  • [Enc] Packet encapsulations: Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4; Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for L2 switching of IPv6.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge-domain (L2BD) switching combined with static MACs, MAC learning enabled and Split Horizon Groups (SHG) depending on test case; VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC7348.
Name Documentation Status
TC01: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels switch ICMPv4 between TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure two i/fs into L2BD with MAC learning. [Ver] Make TG verify ICMPv4 Echo Req pkts are switched thru DUT1 and DUT2 in both directions and are correct on receive. [Ref] RFC7348. PASS
TC02: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels in SHG switch ICMPv4 between TG links [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 configure L2 bridge-domain (MAC learning enabled) with two untagged interfaces to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN interfaces into the same Split-Horizon-Group (SHG). On DUT2 configure two L2 bridge-domain (MAC learning enabled), each with one untagged interface to TG and one VXLAN interface towards the DUT1. [Ver] Make TG send ICMPv4 Echo Reqs between all four of its interfaces to be switched by DUT1 and DUT2; verify packets are not switched between TG interfaces connected to DUT2 that are isolated by SHG on DUT1. [Ref] RFC7348. PASS
TC03: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels in different SHGs switch ICMPv4 between TG links [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 configure L2 bridge-domain (MAC learning enabled) with two untagged interfaces to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN interfaces into the different Split-Horizon-Group (SHGs). On DUT2 configure two L2 bridge-domain (MAC learning enabled), each with one untagged interface to TG and one VXLAN interface towards the DUT1. [Ver] Make TG send ICMPv4 Echo Req between all four of its interfaces to be switched by DUT1 and DUT2; verify packets are switched between all TG interfaces. [Ref] RFC7348. PASS
TC04: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels switch ICMPv6 between TG links [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure L2 bridge-domain (MAC learning enabled), each with one interface to TG and one VXLAN tunnel interface towards the other DUT. [Ver] Make TG send ICMPv6 Echo Req between two of its interfaces to be switched by DUT1 and DUT2; verify all packets are received. [Ref] RFC7348. PASS
TC05: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels in SHG switch ICMPv6 between TG links [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2; Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 configure L2 bridge-domain (MAC learning enabled) with two untagged interfaces to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN interfaces into the same Split-Horizon-Group (SHG). On DUT2 configure two L2 bridge-domain (MAC learning enabled), each with one untagged interface to TG and one VXLAN interface towards the DUT1. [Ver] Make TG send ICMPv6 Echo Reqs between all four of its interfaces to be switched by DUT1 and DUT2; verify packets are not switched between TG interfaces connected to DUT2 that are isolated by SHG on DUT1. [Ref] RFC7348. PASS
TC06: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels in different SHGs switch ICMPv6 between TG links [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2; Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 configure L2 bridge-domain (MAC learning enabled) with two untagged interfaces to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN interfaces into the different Split-Horizon-Group (SHGs). On DUT2 configure two L2 bridge-domain (MAC learning enabled), each with one untagged interface to TG and one VXLAN interface towards the DUT1. [Ver] Make TG send ICMPv6 Echo Req between all four of its interfaces to be switched by DUT1 and DUT2; verify packets are switched between all TG interfaces. [Ref] RFC7348. PASS

Vxlan Xconnect Untagged

  • RFC7348 VXLAN: L2 cross-connect with VXLAN test cases
  • [Top] Network topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross-connect (L2XC) switching; VXLAN tunnels are configured between L2XCs on DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC7348.
Name Documentation Status
TC01: DUT1 and DUT2 with L2XC and VXLANoIPv4 tunnels switch ICMPv4 between TG links [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on [Ref] RFC7348.DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure L2 cross-connect (L2XC), each with one interface to TG and one VXLAN tunnel interface towards the other DUT. [Ver] Make TG send ICMPv4 Echo Req between two of its interfaces; verify all packets are received. [Ref] RFC7348. PASS

Performance Tests - Results

CSIT VPP DUT performance test results in this report have been generated from Robot Framework output log of LF Jenkins Job csit-vpp-perf-1609-all and post processed into wiki format. Original RF report source files are available at Jenkins Job csit-vpp-perf-1609-all: log.html, output.xml, report.html. In addition VPP DUT performance trending graphs have been posted from LF Jenkins Job csit-vpp-perf-1609-all.

Long Performance Tests - NDR and PDR Search

Long Bridge Domain Intel-X520-DA2
  • RFC2544: Pkt throughput L2BD test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7821428 pps (2x 3910714 pps) BANDWIDTH: 5.255 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/67),(10/24/87) LAT_10%NDR:(10/20/69),(10/19/43)

PASS
TC02: 64B PDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7821428 pps (2x 3910714 pps) BANDWIDTH: 5.255 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/124),(20/28/123) LAT_10%NDR:(20/26/78),(20/27/75)

PASS
TC04: 1518B PDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/170),(50/64/168) LAT_10%NDR:(50/58/119),(50/61/74)

PASS
TC06: 9000B PDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 16366666 pps (2x 8183333 pps) BANDWIDTH: 10.998 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/78),(10/28/78) LAT_10%NDR:(10/19/77),(10/18/73)

PASS
TC08: 64B PDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 16597618 pps (2x 8298809 pps) BANDWIDTH: 11.153 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/107),(10/26/71) LAT_10%NDR:(20/27/101),(10/26/57)

PASS
TC10: 1518B PDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/102),(50/66/120) LAT_10%NDR:(50/58/114),(50/61/101)

PASS
TC12: 9000B PDR binary search - DUT L2BD - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/43),(10/18/38) LAT_10%NDR:(10/17/75),(10/17/79)

PASS
TC14: 64B PDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23988094 pps (2x 11994047 pps) BANDWIDTH: 16.119 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/94),(20/27/92) LAT_10%NDR:(20/25/76),(20/24/60)

PASS
TC16: 1518B PDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/134),(50/65/126) LAT_10%NDR:(50/60/95),(50/61/79)

PASS
TC18: 9000B PDR binary search - DUT L2BD - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: IMIX_v4_1 NDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) PASS
TC20: IMIX_v4_1 PDR binary search - DUT L2BD - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Bridge Domain Vhost Intel-X520-DA2
  • RFC2544: Pkt throughput L2BD test cases with vhost
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/618),(10/26/593) LAT_10%NDR:(10/23/340),(10/22/350)

PASS
TC02: 64B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 2082182 pps (2x 1041091 pps) BANDWIDTH: 1.399 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/31/360),(20/35/116) LAT_10%NDR:(20/31/319),(20/30/91)

PASS
TC04: 1518B PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1224114 pps (2x 612057 pps) BANDWIDTH: 15.061 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 309964 pps (2x 154982 pps) BANDWIDTH: 0.927 Gbps (untagged) PASS
TC06: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 1692409 pps (2x 846204 pps) BANDWIDTH: 5.061 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 978479 pps (2x 489239 pps) BANDWIDTH: 0.657 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/348),(10/25/96) LAT_10%NDR:(10/22/334),(10/21/82)

PASS
TC08: 64B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 3011617 pps (2x 1505808 pps) BANDWIDTH: 2.023 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 772571 pps (2x 386285 pps) BANDWIDTH: 9.505 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/34/372),(20/37/145) LAT_10%NDR:(20/29/326),(20/31/91)

PASS
TC10: 1518B PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 492551 pps (2x 246275 pps) BANDWIDTH: 1.473 Gbps (untagged) PASS
TC12: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 3309610 pps (2x 1654805 pps) BANDWIDTH: 9.897 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 397582 pps (2x 198791 pps) BANDWIDTH: 0.267 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/331),(10/22/86) LAT_10%NDR:(10/23/333),(10/19/67)

PASS
TC14: 64B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 4667172 pps (2x 2333586 pps) BANDWIDTH: 3.136 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/31/77),(20/33/402) LAT_10%NDR:(20/30/89),(20/30/340)

PASS
TC16: 1518B PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: IMIX_v4_1 NDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 1170732 pps (2x 585366 pps) BANDWIDTH: 3.501 Gbps (untagged) PASS
TC18: IMIX_v4_1 PDR binary search - DUT L2BD-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 3909539 pps (2x 1954769 pps) BANDWIDTH: 11.692 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: 64B NDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 368537 pps (2x 184268 pps) BANDWIDTH: 0.247 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/363),(10/27/358) LAT_10%NDR:(10/22/337),(10/22/358)

PASS
TC20: 64B PDR binary search - DUT L2BD-DPDK-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 2082182 pps (2x 1041091 pps) BANDWIDTH: 1.399 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Cop Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 whitelist test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/144),(10/28/174) LAT_10%NDR:(10/20/56),(10/17/68)

PASS
TC02: 64B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/29/125),(10/28/81) LAT_10%NDR:(20/25/127),(10/24/155)

PASS
TC04: 1518B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/126),(50/64/158) LAT_10%NDR:(50/61/126),(50/61/117)

PASS
TC06: 9000B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 13826190 pps (2x 6913095 pps) BANDWIDTH: 9.291 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/21/102),(10/22/47) LAT_10%NDR:(10/18/65),(10/16/47)

PASS
TC08: 64B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 13826190 pps (2x 6913095 pps) BANDWIDTH: 9.291 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/144),(10/26/111) LAT_10%NDR:(10/26/88),(10/25/83)

PASS
TC10: 1518B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/193),(50/65/151) LAT_10%NDR:(50/60/114),(50/58/109)

PASS
TC12: 9000B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/141),(10/20/94) LAT_10%NDR:(10/19/75),(10/18/41)

PASS
TC14: 64B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/59),(10/26/94) LAT_10%NDR:(10/24/75),(10/26/65)

PASS
TC16: 1518B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/31/112),(50/32/131) LAT_10%NDR:(50/61/111),(50/60/106)

PASS
TC18: 9000B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Fib 200k Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/76),(10/20/83) LAT_10%NDR:(10/19/46),(10/19/64)

PASS
TC02: 64B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/133),(10/28/132) LAT_10%NDR:(10/25/45),(10/24/67)

PASS
TC04: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/159),(50/63/154) LAT_10%NDR:(50/60/91),(50/60/114)

PASS
TC06: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/50),(10/23/51) LAT_10%NDR:(10/19/65),(10/18/67)

PASS
TC08: 64B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/120),(10/27/154) LAT_10%NDR:(10/25/82),(10/26/96)

PASS
TC10: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/184),(50/63/129) LAT_10%NDR:(50/60/153),(50/60/100)

PASS
TC12: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/41),(10/18/35) LAT_10%NDR:(10/18/37),(10/17/59)

PASS
TC14: 64B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/167),(10/26/71) LAT_10%NDR:(10/25/75),(10/23/53)

PASS
TC16: 1518B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/117),(50/64/116) LAT_10%NDR:(50/60/109),(50/59/105)

PASS
TC18: 9000B PDR binary search - DUT IPv4 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Fib 20k Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/167),(10/26/167) LAT_10%NDR:(10/20/64),(10/19/46)

PASS
TC02: 64B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/150),(10/27/144) LAT_10%NDR:(10/25/125),(10/23/93)

PASS
TC04: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/667),(50/65/631) LAT_10%NDR:(50/57/108),(50/61/98)

PASS
TC06: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/62),(10/27/53) LAT_10%NDR:(10/18/36),(10/19/55)

PASS
TC08: 64B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/87),(10/26/52) LAT_10%NDR:(10/25/107),(10/23/78)

PASS
TC10: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/130),(50/63/181) LAT_10%NDR:(50/59/77),(50/60/100)

PASS
TC12: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/17/35),(10/17/41) LAT_10%NDR:(10/18/86),(10/17/27)

PASS
TC14: 64B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/95),(10/25/101) LAT_10%NDR:(10/25/671),(10/26/633)

PASS
TC16: 1518B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/683),(50/64/652) LAT_10%NDR:(50/60/92),(50/60/90)

PASS
TC18: 9000B PDR binary search - DUT IPv4 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Fib 2M Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8514285 pps (2x 4257142 pps) BANDWIDTH: 5.721 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/9/64),(10/10/59) LAT_10%NDR:(10/19/67),(10/18/48)

PASS
TC02: 64B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8283333 pps (2x 4141666 pps) BANDWIDTH: 5.566 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/157),(10/27/126) LAT_10%NDR:(10/25/56),(10/25/58)

PASS
TC04: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/168),(50/65/183) LAT_10%NDR:(50/57/109),(50/60/112)

PASS
TC06: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 17983332 pps (2x 8991666 pps) BANDWIDTH: 12.084 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/17/61),(10/21/72) LAT_10%NDR:(10/19/37),(10/18/99)

PASS
TC08: 64B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/112),(10/26/57) LAT_10%NDR:(10/26/104),(10/26/61)

PASS
TC10: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/120),(50/65/149) LAT_10%NDR:(50/60/113),(50/60/103)

PASS
TC12: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/17/48),(10/17/45) LAT_10%NDR:(10/17/123),(10/16/70)

PASS
TC14: 64B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/152),(10/27/97) LAT_10%NDR:(10/25/80),(10/26/70)

PASS
TC16: 1518B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/61/145),(50/65/126) LAT_10%NDR:(50/60/95),(50/60/96)

PASS
TC18: 9000B PDR binary search - DUT IPv4 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 iAcl Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 iAcl whitelist test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6897618 pps (2x 3448809 pps) BANDWIDTH: 4.635 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/148),(10/27/111) LAT_10%NDR:(10/19/52),(10/18/114)

PASS
TC02: 64B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/29/141),(10/27/140) LAT_10%NDR:(20/26/81),(10/26/108)

PASS
TC04: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/160),(50/64/154) LAT_10%NDR:(50/57/152),(50/61/148)

PASS
TC06: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 12902380 pps (2x 6451190 pps) BANDWIDTH: 8.670 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/22/99),(10/22/148) LAT_10%NDR:(10/18/74),(10/18/54)

PASS
TC08: 64B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 13133333 pps (2x 6566666 pps) BANDWIDTH: 8.825 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/74),(10/25/164) LAT_10%NDR:(10/25/63),(10/25/83)

PASS
TC10: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/191),(50/65/124) LAT_10%NDR:(50/61/175),(50/61/96)

PASS
TC12: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/36),(10/18/36) LAT_10%NDR:(10/9/115),(10/9/55)

PASS
TC14: 64B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/76),(10/26/89) LAT_10%NDR:(10/13/61),(10/11/80)

PASS
TC16: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/174),(50/63/140) LAT_10%NDR:(50/57/116),(50/60/92)

PASS
TC18: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8745237 pps (2x 4372618 pps) BANDWIDTH: 5.876 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/19/164),(10/34/144) LAT_10%NDR:(10/18/88),(10/18/72)

PASS
TC02: 64B PDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8745237 pps (2x 4372618 pps) BANDWIDTH: 5.876 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/149),(10/27/131) LAT_10%NDR:(10/25/73),(10/26/126)

PASS
TC04: 1518B PDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/121),(50/65/126) LAT_10%NDR:(50/61/119),(50/60/73)

PASS
TC06: 9000B PDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/11/79),(10/15/166) LAT_10%NDR:(10/18/40),(10/19/66)

PASS
TC08: 64B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 18214285 pps (2x 9107142 pps) BANDWIDTH: 12.239 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/96),(10/26/125) LAT_10%NDR:(10/25/91),(10/25/93)

PASS
TC10: 1518B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/170),(50/65/189) LAT_10%NDR:(50/57/102),(50/60/85)

PASS
TC12: 9000B PDR binary search - DUT IPv4 - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/662),(10/17/633) LAT_10%NDR:(10/18/74),(10/17/49)

PASS
TC14: 64B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/71),(10/26/96) LAT_10%NDR:(10/25/37),(10/24/47)

PASS
TC16: 1518B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/101),(50/64/112) LAT_10%NDR:(50/57/110),(50/60/109)

PASS
TC18: 9000B PDR binary search - DUT IPv4 - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: IMIX_v4_1 NDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) PASS
TC20: IMIX_v4_1 PDR binary search - DUT IPv4 - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Policer Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 policer test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC2698.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6897618 pps (2x 3448809 pps) BANDWIDTH: 4.635 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/87),(10/25/172) LAT_10%NDR:(10/20/50),(10/17/34)

PASS
TC02: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7128571 pps (2x 3564285 pps) BANDWIDTH: 4.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/30/164),(10/30/164) LAT_10%NDR:(20/13/112),(10/12/118)

PASS
TC04: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/157),(50/62/138) LAT_10%NDR:(50/61/142),(50/60/111)

PASS
TC06: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 12671428 pps (2x 6335714 pps) BANDWIDTH: 8.515 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/22/98),(10/22/157) LAT_10%NDR:(10/18/39),(10/18/68)

PASS
TC08: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 12671428 pps (2x 6335714 pps) BANDWIDTH: 8.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/76),(10/26/119) LAT_10%NDR:(10/26/65),(10/23/55)

PASS
TC10: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/221),(50/64/128) LAT_10%NDR:(50/57/101),(50/60/156)

PASS
TC12: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 22140475 pps (2x 11070237 pps) BANDWIDTH: 14.878 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/77),(10/21/101) LAT_10%NDR:(10/18/34),(10/17/82)

PASS
TC14: 64B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 17521428 pps (2x 8760714 pps) BANDWIDTH: 11.774 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/12/91),(20/12/106) LAT_10%NDR:(10/25/42),(10/26/76)

PASS
TC16: 1518B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/115),(50/65/118) LAT_10%NDR:(50/57/124),(50/57/97)

PASS
TC18: 9000B PDR binary search - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv4 Vhost Intel-X520-DA2
  • RFC2544: Pkt throughput IPv4 test cases with vhost
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores dedicated for io), forwarding mode is set to mac, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 339493 pps (2x 169746 pps) BANDWIDTH: 0.228 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/78),(10/23/354) LAT_10%NDR:(10/23/46),(10/22/353)

PASS
TC02: 64B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1995048 pps (2x 997524 pps) BANDWIDTH: 1.340 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 446457 pps (2x 223228 pps) BANDWIDTH: 5.493 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/36/463),(20/37/152) LAT_10%NDR:(20/30/402),(20/31/60)

PASS
TC04: 1518B PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1199028 pps (2x 599514 pps) BANDWIDTH: 14.752 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 257796 pps (2x 128898 pps) BANDWIDTH: 0.770 Gbps (untagged) PASS
TC06: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 1thread 1core 1rxq [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 1248984 pps (2x 624492 pps) BANDWIDTH: 3.735 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 455672 pps (2x 227836 pps) BANDWIDTH: 0.306 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/97),(10/25/347) LAT_10%NDR:(10/21/164),(10/23/352)

PASS
TC08: 64B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 3708693 pps (2x 1854346 pps) BANDWIDTH: 2.492 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/33/377),(20/34/98) LAT_10%NDR:(20/30/340),(20/31/84)

PASS
TC10: 1518B PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 414300 pps (2x 207150 pps) BANDWIDTH: 1.239 Gbps (untagged) PASS
TC12: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 3557407 pps (2x 1778703 pps) BANDWIDTH: 10.639 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/71),(10/22/74) LAT_10%NDR:(10/22/189),(10/19/52)

PASS
TC14: 64B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 4086275 pps (2x 2043137 pps) BANDWIDTH: 2.745 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 371200 pps (2x 185600 pps) BANDWIDTH: 4.567 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/32/356),(20/32/364) LAT_10%NDR:(20/27/383),(20/31/331)

PASS
TC16: 1518B PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: IMIX_v4_1 NDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 857725 pps (2x 428862 pps) BANDWIDTH: 2.565 Gbps (untagged) PASS
TC18: IMIX_v4_1 PDR binary search - DUT IPv4-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 3622616 pps (2x 1811308 pps) BANDWIDTH: 10.834 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 Cop Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 whitelist test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6132079 pps (2x 3066039 pps) BANDWIDTH: 4.807 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/75),(10/25/74) LAT_10%NDR:(10/20/46),(10/16/87)

PASS
TC02: 78B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 6132079 pps (2x 3066039 pps) BANDWIDTH: 4.807 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1600400 pps (2x 800200 pps) BANDWIDTH: 19.691 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/64),(20/30/54) LAT_10%NDR:(20/26/88),(10/26/72)

PASS
TC04: 1518B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/97),(50/64/116) LAT_10%NDR:(50/57/93),(50/61/132)

PASS
TC06: 9000B PDR binary search - DUT IPv6 whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 10482270 pps (2x 5241135 pps) BANDWIDTH: 8.218 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/59),(10/24/88) LAT_10%NDR:(10/10/47),(10/8/46)

PASS
TC08: 78B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/63),(20/26/115) LAT_10%NDR:(20/25/95),(10/25/115)

PASS
TC10: 1518B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/190),(50/65/138) LAT_10%NDR:(50/57/123),(50/58/105)

PASS
TC12: 9000B PDR binary search - DUT IPv6 whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/19/74),(10/19/74) LAT_10%NDR:(10/18/38),(10/17/67)

PASS
TC14: 78B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/86),(20/26/80) LAT_10%NDR:(20/25/75),(10/26/92)

PASS
TC16: 1518B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/186),(50/64/121) LAT_10%NDR:(50/57/85),(50/58/111)

PASS
TC18: 9000B PDR binary search - DUT IPv6 whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 Fib 200k Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/12/237),(10/12/230) LAT_10%NDR:(10/20/69),(10/19/58)

PASS
TC02: 78B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/190),(10/28/190) LAT_10%NDR:(10/25/117),(10/24/132)

PASS
TC04: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/201),(50/64/181) LAT_10%NDR:(50/57/145),(50/57/118)

PASS
TC06: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 13646045 pps (2x 6823022 pps) BANDWIDTH: 10.698 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/127),(10/26/114) LAT_10%NDR:(10/19/110),(10/19/71)

PASS
TC08: 78B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 14041517 pps (2x 7020758 pps) BANDWIDTH: 11.008 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/181),(10/26/89) LAT_10%NDR:(10/25/75),(10/24/78)

PASS
TC10: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/179),(50/65/220) LAT_10%NDR:(50/57/69),(50/60/188)

PASS
TC12: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/10/141),(10/9/86) LAT_10%NDR:(10/18/62),(10/15/42)

PASS
TC14: 78B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 21555484 pps (2x 10777742 pps) BANDWIDTH: 16.899 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/81),(20/26/147) LAT_10%NDR:(10/25/106),(10/26/130)

PASS
TC16: 1518B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/119),(50/63/96) LAT_10%NDR:(50/59/88),(50/60/77)

PASS
TC18: 9000B PDR binary search - DUT IPv6 Fib 2x100k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 Fib 20k Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/609),(10/24/592) LAT_10%NDR:(10/20/419),(10/17/399)

PASS
TC02: 78B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 6923022 pps (2x 3461511 pps) BANDWIDTH: 5.427 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/109),(10/27/112) LAT_10%NDR:(10/26/105),(10/25/83)

PASS
TC04: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/506),(50/63/481) LAT_10%NDR:(50/61/87),(50/61/135)

PASS
TC06: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 14436989 pps (2x 7218494 pps) BANDWIDTH: 11.318 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/112),(10/24/127) LAT_10%NDR:(10/20/45),(10/18/68)

PASS
TC08: 78B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 14436989 pps (2x 7218494 pps) BANDWIDTH: 11.318 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/126),(10/27/95) LAT_10%NDR:(10/26/618),(10/26/683)

PASS
TC10: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/397),(50/65/479) LAT_10%NDR:(50/28/143),(50/28/100)

PASS
TC12: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/55),(10/18/140) LAT_10%NDR:(10/18/57),(10/16/122)

PASS
TC14: 78B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/87),(10/27/70) LAT_10%NDR:(20/25/93),(10/26/50)

PASS
TC16: 1518B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/60/110),(50/65/121) LAT_10%NDR:(50/57/106),(50/60/83)

PASS
TC18: 9000B PDR binary search - DUT IPv6 Fib 2x10k - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 Fib 2M Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 5341135 pps (2x 2670567 pps) BANDWIDTH: 4.187 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/592),(10/27/683) LAT_10%NDR:(10/19/45),(10/18/54)

PASS
TC02: 78B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 5341135 pps (2x 2670567 pps) BANDWIDTH: 4.187 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/30/669),(10/29/667) LAT_10%NDR:(10/26/164),(10/25/139)

PASS
TC04: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/194),(50/64/257) LAT_10%NDR:(50/57/107),(50/60/101)

PASS
TC06: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/660),(10/27/643) LAT_10%NDR:(10/20/162),(10/18/74)

PASS
TC08: 78B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 10877742 pps (2x 5438871 pps) BANDWIDTH: 8.528 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/180),(10/27/80) LAT_10%NDR:(10/26/159),(10/24/74)

PASS
TC10: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/240),(50/63/659) LAT_10%NDR:(50/57/102),(50/60/160)

PASS
TC12: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 20764540 pps (2x 10382270 pps) BANDWIDTH: 16.279 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/21/48),(10/21/45) LAT_10%NDR:(10/18/70),(2/17/49)

PASS
TC14: 78B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 20764540 pps (2x 10382270 pps) BANDWIDTH: 16.279 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/59),(10/26/200) LAT_10%NDR:(10/25/50),(10/25/77)

PASS
TC16: 1518B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/101),(50/66/156) LAT_10%NDR:(50/60/78),(50/61/110)

PASS
TC18: 9000B PDR binary search - DUT IPv6 Fib 2x1M - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 iAcl Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 iAcl whitelist test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/71),(10/25/81) LAT_10%NDR:(10/20/558),(10/17/537)

PASS
TC02: 78B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 6527551 pps (2x 3263775 pps) BANDWIDTH: 5.117 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/97),(20/28/95) LAT_10%NDR:(20/25/101),(10/24/128)

PASS
TC04: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/129),(50/63/123) LAT_10%NDR:(50/60/105),(50/60/137)

PASS
TC06: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 11273214 pps (2x 5636607 pps) BANDWIDTH: 8.838 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/768),(10/23/750) LAT_10%NDR:(10/18/72),(10/22/83)

PASS
TC08: 78B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 11273214 pps (2x 5636607 pps) BANDWIDTH: 8.838 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/168),(10/26/95) LAT_10%NDR:(10/25/69),(10/24/52)

PASS
TC10: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/113),(50/63/137) LAT_10%NDR:(50/57/100),(50/61/120)

PASS
TC12: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 20369068 pps (2x 10184534 pps) BANDWIDTH: 15.969 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/19/39),(10/20/66) LAT_10%NDR:(10/18/64),(10/17/68)

PASS
TC14: 78B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/125),(10/26/79) LAT_10%NDR:(20/26/67),(10/23/68)

PASS
TC16: 1518B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/130),(50/64/125) LAT_10%NDR:(50/61/91),(50/60/74)

PASS
TC18: 9000B PDR binary search - DUT IPv6 iAcl whitelist - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long IPv6 Intel-X520-DA2
  • RFC2544: Pkt throughput IPv6 routing test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 78B NDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 2968303 pps (2x 1484151 pps) BANDWIDTH: 2.327 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/19/37),(10/21/70) LAT_10%NDR:(10/19/557),(10/17/535)

PASS
TC02: 78B PDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7713966 pps (2x 3856983 pps) BANDWIDTH: 6.047 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/585),(10/28/657) LAT_10%NDR:(10/25/84),(10/25/61)

PASS
TC04: 1518B PDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/142),(50/64/144) LAT_10%NDR:(50/60/113),(50/57/106)

PASS
TC06: 9000B PDR binary search - DUT IPv6 - 1thread 1core 1rxq [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 78B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 15227933 pps (2x 7613966 pps) BANDWIDTH: 11.938 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/592),(10/24/562) LAT_10%NDR:(10/18/68),(10/20/53)

PASS
TC08: 78B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 15623405 pps (2x 7811702 pps) BANDWIDTH: 12.248 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/677),(10/27/654) LAT_10%NDR:(10/25/45),(10/26/118)

PASS
TC10: 1518B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/31/173),(50/32/143) LAT_10%NDR:(50/57/117),(50/61/108)

PASS
TC12: 9000B PDR binary search - DUT IPv6 - 2threads 2cores 1rxq [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 78B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/17/75),(10/17/121) LAT_10%NDR:(10/18/32),(10/17/69)

PASS
TC14: 78B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 21160012 pps (2x 10580006 pps) BANDWIDTH: 16.589 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/25/130),(10/26/94) LAT_10%NDR:(20/25/49),(10/23/75)

PASS
TC16: 1518B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/66/164),(50/66/105) LAT_10%NDR:(50/61/154),(50/61/105)

PASS
TC18: 9000B PDR binary search - DUT IPv6 - 4threads 4cores 2rxq [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Lisp Intel-X520-DA2
  • RFC6830: Pkt throughput Lisp test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 (IPv6) routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 4414673 pps (2x 2207336 pps) BANDWIDTH: 2.966 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/36/738),(10/39/698) LAT_10%NDR:(10/21/63),(10/21/56)

PASS
TC02: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 4625407 pps (2x 2312703 pps) BANDWIDTH: 3.108 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/32/786),(20/32/781) LAT_10%NDR:(20/26/103),(20/26/76)

PASS
TC04: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/66/809),(50/67/777) LAT_10%NDR:(50/58/109),(50/62/82)

PASS
TC06: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/30/99),(10/31/168) LAT_10%NDR:(10/20/64),(10/20/51)

PASS
TC08: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/29/781),(20/27/734) LAT_10%NDR:(20/26/86),(20/24/76)

PASS
TC10: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/67/676),(50/67/650) LAT_10%NDR:(50/58/69),(50/61/105)

PASS
TC12: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7997146 pps (2x 3998573 pps) BANDWIDTH: 5.374 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/21/134),(10/22/98) LAT_10%NDR:(10/10/79),(10/10/56)

PASS
TC14: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8207880 pps (2x 4103940 pps) BANDWIDTH: 5.515 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.279 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/44),(20/28/76) LAT_10%NDR:(20/26/86),(20/26/71)

PASS
TC16: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.586 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/66/120),(50/66/113) LAT_10%NDR:(50/59/73),(50/61/105)

PASS
TC18: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 3488502 pps (2x 1744251 pps) BANDWIDTH: 2.734 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/33/130),(10/35/114) LAT_10%NDR:(10/10/83),(10/12/84)

PASS
TC20: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 3853891 pps (2x 1926945 pps) BANDWIDTH: 3.021 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC21: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/37/95),(20/37/111) LAT_10%NDR:(20/28/744),(20/29/811)

PASS
TC22: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC23: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/67/121),(50/68/134) LAT_10%NDR:(50/61/97),(50/63/86)

PASS
TC24: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC25: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/29/113),(10/30/169) LAT_10%NDR:(10/20/124),(10/20/80)

PASS
TC26: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC27: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/29/77),(20/29/77) LAT_10%NDR:(20/27/42),(20/26/56)

PASS
TC28: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC29: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/133),(50/67/97) LAT_10%NDR:(50/64/724),(50/64/697)

PASS
TC30: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC31: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7873171 pps (2x 3936585 pps) BANDWIDTH: 6.172 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/26/104),(10/25/137) LAT_10%NDR:(10/21/747),(10/21/707)

PASS
TC32: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8238560 pps (2x 4119280 pps) BANDWIDTH: 6.459 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC33: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 1606642 pps (2x 803321 pps) BANDWIDTH: 19.022 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/723),(20/28/708) LAT_10%NDR:(20/27/46),(20/27/43)

PASS
TC34: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1632233 pps (2x 816116 pps) BANDWIDTH: 19.325 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC35: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/66/774),(50/67/841) LAT_10%NDR:(50/63/81),(50/60/108)

PASS
TC36: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 260233 pps (2x 130116 pps) BANDWIDTH: 18.778 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC37: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 4006439 pps (2x 2003219 pps) BANDWIDTH: 2.692 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/31/743),(10/31/726) LAT_10%NDR:(10/22/87),(10/22/69)

PASS
TC38: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 4006439 pps (2x 2003219 pps) BANDWIDTH: 2.692 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC39: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/39/79),(20/39/75) LAT_10%NDR:(20/26/42),(20/29/84)

PASS
TC40: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC41: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/68/177),(50/66/154) LAT_10%NDR:(50/60/131),(50/63/117)

PASS
TC42: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC43: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/37/722),(10/38/820) LAT_10%NDR:(10/20/42),(10/20/68)

PASS
TC44: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC45: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/29/70),(20/29/57) LAT_10%NDR:(20/27/749),(20/25/708)

PASS
TC46: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC47: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/82),(50/67/130) LAT_10%NDR:(50/60/112),(50/59/105)

PASS
TC48: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC49: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/70),(10/25/73) LAT_10%NDR:(10/20/47),(10/20/67)

PASS
TC50: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7812878 pps (2x 3906439 pps) BANDWIDTH: 5.250 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC51: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/95),(20/27/75) LAT_10%NDR:(20/26/71),(20/24/105)

PASS
TC52: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1610872 pps (2x 805436 pps) BANDWIDTH: 19.072 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC53: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 259088 pps (2x 129544 pps) BANDWIDTH: 18.695 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/114),(50/65/139) LAT_10%NDR:(50/59/782),(50/63/750)

PASS
TC54: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC55: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 4166395 pps (2x 2083197 pps) BANDWIDTH: 3.266 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/32/85),(10/35/118) LAT_10%NDR:(10/21/663),(10/20/740)

PASS
TC56: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 4166395 pps (2x 2083197 pps) BANDWIDTH: 3.266 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC57: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/34/156),(20/34/167) LAT_10%NDR:(20/26/89),(20/26/73)

PASS
TC58: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC59: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/32/124),(50/33/162) LAT_10%NDR:(50/59/580),(50/62/545)

PASS
TC60: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC61: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/56),(10/30/58) LAT_10%NDR:(10/22/85),(10/22/55)

PASS
TC62: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC63: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/152),(20/28/114) LAT_10%NDR:(20/26/90),(20/24/49)

PASS
TC64: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC65: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/185),(50/66/138) LAT_10%NDR:(50/62/544),(50/58/479)

PASS
TC66: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC67: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 8397216 pps (2x 4198608 pps) BANDWIDTH: 6.583 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/75),(10/25/57) LAT_10%NDR:(10/20/691),(10/21/666)

PASS
TC68: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 8661643 pps (2x 4330821 pps) BANDWIDTH: 6.790 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC69: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/112),(20/29/98) LAT_10%NDR:(20/26/78),(20/27/76)

PASS
TC70: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1636124 pps (2x 818062 pps) BANDWIDTH: 19.371 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC71: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/136),(50/65/174) LAT_10%NDR:(50/59/135),(50/62/122)

PASS
TC72: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275694 pps (2x 137847 pps) BANDWIDTH: 19.894 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Xconnect Dot1ad Intel-X520-DA2
  • RFC2544: Pkt throughput L2XC with 802.1ad test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 xconnect. 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B vlan tag (id=100) and outer 4B vlan tag (id=200).
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7364945 pps (2x 3682472 pps) BANDWIDTH: 4.949 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/612),(10/28/604) LAT_10%NDR:(10/19/35),(10/16/81)

PASS
TC02: 64B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7364945 pps (2x 3682472 pps) BANDWIDTH: 4.949 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1514B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/143),(10/27/139) LAT_10%NDR:(20/25/47),(10/23/107)

PASS
TC04: 1514B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/162),(50/64/143) LAT_10%NDR:(50/61/487),(50/61/460)

PASS
TC06: 9000B PDR binary search - DUT L2XC with 802.1ad - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 14951358 pps (2x 7475679 pps) BANDWIDTH: 10.047 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/11/145),(10/11/76) LAT_10%NDR:(10/20/86),(10/18/66)

PASS
TC08: 64B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 15162091 pps (2x 7581045 pps) BANDWIDTH: 10.188 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1514B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/582),(10/26/666) LAT_10%NDR:(10/25/83),(10/23/93)

PASS
TC10: 1514B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/134),(50/65/181) LAT_10%NDR:(50/60/76),(50/60/162)

PASS
TC12: 9000B PDR binary search - DUT L2XC with 802.1ad - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 16005026 pps (2x 8002513 pps) BANDWIDTH: 10.755 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/47),(10/17/158) LAT_10%NDR:(10/18/34),(10/17/39)

PASS
TC14: 64B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 16426493 pps (2x 8213246 pps) BANDWIDTH: 11.038 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1514B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/642),(10/27/614) LAT_10%NDR:(10/25/75),(10/24/61)

PASS
TC16: 1514B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.896 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/62/105),(50/65/127) LAT_10%NDR:(50/60/134),(50/61/95)

PASS
TC18: 9000B PDR binary search - DUT L2XC with 802.1ad - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 276916 pps (2x 138458 pps) BANDWIDTH: 19.982 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Xconnect Dot1q Intel-X520-DA2
  • RFC2544: Pkt throughput L2XC with 802.1q test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 7472656 pps (2x 3736328 pps) BANDWIDTH: 5.021 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/23/177),(10/22/141) LAT_10%NDR:(10/19/49),(10/17/35)

PASS
TC02: 64B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 7472656 pps (2x 3736328 pps) BANDWIDTH: 5.021 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/117),(20/28/113) LAT_10%NDR:(20/25/119),(10/25/84)

PASS
TC04: 1518B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/130),(50/66/128) LAT_10%NDR:(50/60/530),(50/60/602)

PASS
TC06: 9000B PDR binary search - DUT L2XC with 802.1q - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 14965695 pps (2x 7482847 pps) BANDWIDTH: 10.056 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/22/130),(10/23/87) LAT_10%NDR:(10/17/57),(10/18/38)

PASS
TC08: 64B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 14965695 pps (2x 7482847 pps) BANDWIDTH: 10.056 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/136),(10/25/72) LAT_10%NDR:(10/25/113),(10/23/71)

PASS
TC10: 1518B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/89),(50/65/184) LAT_10%NDR:(50/57/591),(50/61/553)

PASS
TC12: 9000B PDR binary search - DUT L2XC with 802.1q - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23340269 pps (2x 11670134 pps) BANDWIDTH: 15.684 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/18/620),(10/18/603) LAT_10%NDR:(10/18/71),(10/15/53)

PASS
TC14: 64B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23560652 pps (2x 11780326 pps) BANDWIDTH: 15.832 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/27/59),(10/26/66) LAT_10%NDR:(10/26/76),(10/25/87)

PASS
TC16: 1518B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1621270 pps (2x 810635 pps) BANDWIDTH: 19.948 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/135),(50/64/124) LAT_10%NDR:(50/60/551),(50/61/527)

PASS
TC18: 9000B PDR binary search - DUT L2XC with 802.1q - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277038 pps (2x 138519 pps) BANDWIDTH: 19.991 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Xconnect Intel-X520-DA2
  • RFC2544: Pkt throughput L2XC test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 9438095 pps (2x 4719047 pps) BANDWIDTH: 6.342 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/85),(10/22/79) LAT_10%NDR:(10/18/69),(10/19/60)

PASS
TC02: 64B PDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 9438095 pps (2x 4719047 pps) BANDWIDTH: 6.342 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/26/147),(10/27/123) LAT_10%NDR:(10/26/137),(10/25/106)

PASS
TC04: 1518B PDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/63/171),(50/65/172) LAT_10%NDR:(50/60/103),(50/57/95)

PASS
TC06: 9000B PDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 20061904 pps (2x 10030952 pps) BANDWIDTH: 13.481 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/20/88),(10/19/50) LAT_10%NDR:(10/18/35),(10/18/34)

PASS
TC08: 64B PDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 20292856 pps (2x 10146428 pps) BANDWIDTH: 13.636 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/161),(10/26/99) LAT_10%NDR:(10/26/123),(10/24/94)

PASS
TC10: 1518B PDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/154),(50/66/97) LAT_10%NDR:(50/60/109),(50/58/178)

PASS
TC12: 9000B PDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 23526189 pps (2x 11763094 pps) BANDWIDTH: 15.809 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/16/66),(10/16/45) LAT_10%NDR:(10/17/40),(10/17/29)

PASS
TC14: 64B PDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 23757142 pps (2x 11878571 pps) BANDWIDTH: 15.964 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/62),(10/25/64) LAT_10%NDR:(10/26/63),(10/26/113)

PASS
TC16: 1518B PDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/153),(50/64/102) LAT_10%NDR:(50/57/112),(50/60/117)

PASS
TC18: 9000B PDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 277160 pps (2x 138580 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) PASS
TC20: IMIX_v4_1 PDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 6687472 pps (2x 3343736 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Xconnect Intel-XL710
  • RFC2544: Pkt throughput L2XC test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 9525000 pps (2x 4762500 pps) BANDWIDTH: 6.400 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/159),(10/27/172) LAT_10%NDR:(10/23/72),(10/22/80)

PASS
TC03: 1518B NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 3703834 pps (2x 1851917 pps) BANDWIDTH: 45.571 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/27/51),(10/26/56) LAT_10%NDR:(20/28/74),(10/28/57)

PASS
TC07: 64B NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 15644531 pps (2x 7822265 pps) BANDWIDTH: 10.513 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/22/62),(10/21/168) LAT_10%NDR:(10/24/60),(10/25/40)

PASS
TC09: 1518B NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 3734791 pps (2x 1867395 pps) BANDWIDTH: 45.952 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/143),(10/26/86) LAT_10%NDR:(20/26/67),(10/25/82)

PASS
TC13: 64B NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 30797656 pps (2x 15398828 pps) BANDWIDTH: 20.696 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/16/109),(10/16/151) LAT_10%NDR:(10/20/33),(10/19/32)

PASS
TC15: 1518B NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 3982444 pps (2x 1991222 pps) BANDWIDTH: 48.999 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/29/146),(10/27/119) LAT_10%NDR:(10/27/72),(10/26/158)

PASS
TC19: IMIX_v4_1 NDR binary search - DUT L2XC - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 9556551 pps (2x 4778275 pps) BANDWIDTH: 28.580 Gbps (untagged) PASS
TC20: IMIX_v4_1 NDR binary search - DUT L2XC - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 16384306 pps (2x 8192153 pps) BANDWIDTH: 48.999 Gbps (untagged) PASS
TC21: IMIX_v4_1 NDR binary search - DUT L2XC - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 16384306 pps (2x 8192153 pps) BANDWIDTH: 48.999 Gbps (untagged) PASS
Long Xconnect Vhost Intel-X520-DA2
  • RFC2544: Pkt throughput L2XC test cases with vhost
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 3 cores pinned to cpus 5,6,7 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 3 cores (1 main core and 2 cores 2 cores dedicated for io), forwarding mode is set to io, rxq/txq=2048, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 542806 pps (2x 271403 pps) BANDWIDTH: 0.364 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/29/352),(10/29/167) LAT_10%NDR:(10/22/298),(10/22/91)

PASS
TC02: 64B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 2575944 pps (2x 1287972 pps) BANDWIDTH: 1.731 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 270857 pps (2x 135428 pps) BANDWIDTH: 3.332 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/31/313),(20/31/356) LAT_10%NDR:(20/30/337),(20/30/358)

PASS
TC04: 1518B PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1324457 pps (2x 662228 pps) BANDWIDTH: 16.296 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 362132 pps (2x 181066 pps) BANDWIDTH: 1.083 Gbps (untagged) PASS
TC06: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 2044542 pps (2x 1022271 pps) BANDWIDTH: 6.114 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 542806 pps (2x 271403 pps) BANDWIDTH: 0.364 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/21/376),(10/25/102) LAT_10%NDR:(10/22/469),(10/19/69)

PASS
TC08: 64B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 4521948 pps (2x 2260974 pps) BANDWIDTH: 3.038 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/32/339),(20/29/368) LAT_10%NDR:(20/29/311),(20/27/342)

PASS
TC10: 1518B PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 870767 pps (2x 435383 pps) BANDWIDTH: 2.604 Gbps (untagged) PASS
TC12: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 2threads 2cores 1rxq [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 3961707 pps (2x 1980853 pps) BANDWIDTH: 11.848 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 717075 pps (2x 358537 pps) BANDWIDTH: 0.481 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/22/342),(10/21/313) LAT_10%NDR:(10/11/356),(10/11/329)

PASS
TC14: 64B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 4754306 pps (2x 2377153 pps) BANDWIDTH: 3.194 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 396285 pps (2x 198142 pps) BANDWIDTH: 4.875 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/31/174),(20/30/314) LAT_10%NDR:(20/27/54),(20/30/354)

PASS
TC16: 1518B PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1625486 pps (2x 812743 pps) BANDWIDTH: 19.999 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: IMIX_v4_1 NDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 557761 pps (2x 278880 pps) BANDWIDTH: 1.668 Gbps (untagged) PASS
TC18: IMIX_v4_1 PDR binary search - DUT L2XC-VHOST - 4threads 4cores 2rxq [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) RATE: 4222545 pps (2x 2111272 pps) BANDWIDTH: 12.628 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC19: 64B NDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 426627 pps (2x 213313 pps) BANDWIDTH: 0.286 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/24/102),(10/24/356) LAT_10%NDR:(10/22/72),(10/22/327)

PASS
TC20: 64B PDR binary search - DUT L2XC-DPDK-VHOST - 1thread 1core 1rxq [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 2314541 pps (2x 1157270 pps) BANDWIDTH: 1.555 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
Long Xconnect Vxlan Ipv4 Intel-X520-DA2
  • RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases
  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name Documentation Message Status
TC01: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 5390951 pps (2x 2695475 pps) BANDWIDTH: 3.622 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/32/644),(10/32/624) LAT_10%NDR:(10/22/637),(10/19/614)

PASS
TC02: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 5390951 pps (2x 2695475 pps) BANDWIDTH: 3.622 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC03: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/31/584),(20/34/656) LAT_10%NDR:(20/26/132),(20/28/149)

PASS
TC04: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC05: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/65/191),(50/67/192) LAT_10%NDR:(50/58/89),(50/61/156)

PASS
TC06: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 1thread 1core 1rxq [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC07: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 10870288 pps (2x 5435144 pps) BANDWIDTH: 7.304 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/28/56),(10/29/109) LAT_10%NDR:(10/19/40),(10/20/66)

PASS
TC08: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 11158675 pps (2x 5579337 pps) BANDWIDTH: 7.498 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC09: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(20/28/109),(20/29/155) LAT_10%NDR:(20/26/89),(20/25/84)

PASS
TC10: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC11: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/67/192),(50/67/145) LAT_10%NDR:(50/61/141),(50/60/106)

PASS
TC12: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 2threads 2cores 1rxq [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC13: 64B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. RATE: 18656716 pps (2x 9328358 pps) BANDWIDTH: 12.537 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(10/25/104),(10/26/157) LAT_10%NDR:(10/20/67),(10/19/76)

PASS
TC14: 64B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. RATE: 18656716 pps (2x 9328358 pps) BANDWIDTH: 12.537 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC15: 1518B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(2/27/99),(20/28/84) LAT_10%NDR:(20/26/553),(20/27/629)

PASS
TC16: 1518B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. RATE: 1574306 pps (2x 787153 pps) BANDWIDTH: 19.370 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS
TC17: 9000B NDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged)

LATENCY [usec] (min/avg/max) LAT_50%NDR:(50/64/770),(50/64/724) LAT_10%NDR:(50/58/119),(50/58/97)

PASS
TC18: 9000B PDR binary search - DUT L2XC with VXLANoIPv4 - 4threads 4cores 2rxq [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. RATE: 275632 pps (2x 137816 pps) BANDWIDTH: 19.889 Gbps (untagged) LOSS_ACCEPTANCE: 0.5% PASS

Failed Functional Tests

Dhcp Client

One test for DHCP Client fails due to a known issue in the VPP code. Latest status tracked in FD.io CSIT and VPP Jira:

  • Error while calling JIRA...
Name Documentation Status
VPP doesn't send DHCP REQUEST after OFFER with wrong XID Configure DHCP client on interface to TG. If server sends DHCP OFFER with different XID as in DHCP DISCOVER, DHCP REQUEST message shouldn't be sent. FAIL
Name Documentation Status
VPP doesn't send DHCP REQUEST after OFFER with wrong XID Configure DHCP client on interface to TG. If server sends DHCP OFFER with different XID as in DHCP DISCOVER, DHCP REQUEST message shouldn't be sent. FAIL

Lisp Api Untagged

One Lisp Api Untagged test fails due to a known issue in the VPP code. Latest status tracked in FD.io CSIT and VPP Jira:

Note: This patch was not merged to stable/1609 vpp branch.

Name Documentation Status
TC03: DUT can add, reset and delete locator_set [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on DUT1 configure locator_set and locator. [Ver1] Check DUT1 locator_set and locator are correct. [Cfg2] Then reset locator_set and set it again. [Ver2] Check DUT1 locator_set and locator are correct. [Cfg3] Then remove locator_set and locator. [Ver3] Check DUT1 all locator_set and locators are removed. [Ref] RFC6830. FAIL

Ipv6 Ra

Two of Ipv6 Ra tests fail due to a known issue in the VPP code. Latest status tracked in FD.io CSIT and VPP Jira:

Name Documentation Status
TC03: DUT responds to Router Solicitation request [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPv6 interface on the link to TG and suppress sending of Router Advertisement packets periodically. [Ver] Make TG send IPv6 Router Solicitation request to DUT1, listen for response from DUT1 and verify the received RA packet is correct. FAIL
TC04: DUT responds to Router Solicitation request sent from link local address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPv6 interface on the link to TG and suppress sending of Router Advertisement packets periodically. [Ver] Make TG send IPv6 Router Solicitation request to DUT1, listen for response from DUT1 and verify the received RA packet is correct. FAIL

Ipfix

CSIT IPFIX tests fail due to a known issue in IPFIX code that is still being completed. Latest status tracked in FD.io CSIT and VPP Jira:

Ipfix Ipv4

  • IPFIX ipv4 test cases IPFIX tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 is configured with IPv4 routing and static routes. IPFIX is configured on DUT1 with DUT1->TG interface as collector. Test packets are sent from TG to DUT1. TG listens for flow report packets and verifies that they contains flow record of test packets sent.
Name Documentation Status
TC01: DUT sends IPFIX template and data packets [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and a basic classify session. [Ver] Make TG listen for IPFIX template and data packets, verify that packet is received and correct. No packets are sent from TG. [Ref] RFC 7011 FAIL
TC02: DUT reports packet flow for traffic by source address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC03: DUT reports packet flow for traffic with local destination address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with destination address of DUT1. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC04: DUT reports packet flow for traffic with remote destination address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with destination address of DUT2. [Ver] Make TG send a packet to DUT2 through DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC05: DUT reports packet flow for traffic by source and destination port [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address and source and destination ports. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC06: DUT reports packet flow with a large number of packets [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address. [Ver] Make TG send packets to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packets. [Ref] RFC 7011 FAIL
TC07: DUT reports packet flow when multiple sessions are configured [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add several classify sessions with different ports. [Ver] Make TG send packets to DUT1 using a range of ports matching configured sessions, then listen for IPFIX template and data packets, verify that IPFIX reported the received packets for each session. [Ref] RFC 7011 FAIL

Ipfix Ipv6

  • IPFIX ipv6 test cases IPFIX tests use 3-node topology TG - DUT1 - DUT2 - TG with one link between the nodes. DUT1 is configured with IPv4 and IPV6 routing and static routes. IPFIX is configured on DUT1 with DUT1->TG interface as collector.Test packets are sent from TG to or through DUT1. TG listens for flow report packets and verifies that they contains flow records of test packets sent.
Name Documentation Status
TC01: DUT reports packet flow for traffic by source address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC02: DUT reports packet flow for traffic with local destination address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with destination address of DUT1. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC03: DUT reports packet flow for traffic with remote destination address [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with destination address of DUT2. [Ver] Make TG send a packet to DUT2 through DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC04: DUT reports packet flow for traffic by source and destination port [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address and source and destination ports. [Ver] Make TG send a packet to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packet. [Ref] RFC 7011 FAIL
TC05: DUT reports packet flow with a large number of packets [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add classify session with TG source address. [Ver] Make TG send packets to DUT1, then listen for IPFIX template and data packets, verify that IPFIX reported the received packets. [Ref] RFC 7011 FAIL
TC06: DUT reports packet flow when multiple sessions are configured [Top] TG-DUT1-DUT2-TG. [Cfg] On DUT1 configure IPFIX with TG interface address as collector and add several classify sessions with different ports. [Ver] Make TG send packets to DUT1 using a range of ports matching configured sessions, then listen for IPFIX template and data packets, verify that IPFIX reported the received packets for each session. [Ref] RFC 7011 FAIL

Softwire

Listed CSIT Softwire negative tests fail due to known issues in MAP-E/T code. Latest status tracked in FD.io CSIT and VPP Jira:

  • Error while calling JIRA...
  • Error while calling JIRA...

Map E

  • Test for Basic mapping rule for MAP-E
  • [Top] Network Topologies: TG - DUT1 - TG with two links between the nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP on TG-to-DUT-if1. Eth-IPv6-IPv4-UDP on TG-to-DUT-if2.
  • [Cfg] DUT configuration: DUT is configured with IPv4 on one DUT-to-TG interface and IPv6 address on second DUT-to-TG interface. MAP-E domain is configured in test template based on test parameters.
  • [Ver] TG verification: UDP packets in IPv4 are sent by TG to destination in MAP domain. IPv6 packets with encapsulated IPv4 are received on TG interface.
  • [Ref] Applicable standard specifications: RFC7597.
Name Documentation Status
TC01: BMR, then an IPv4 prefix is assigned Basic Mapping Rule https://tools.ietf.org/html/rfc7597#section-5.2 IPv4 prefix length + ea bits length < 32 (o + r < 32) psid_length = 0, ip6_prefix < 64, ip4_prefix <= 32 FAIL
TC02: BMR, full IPv4 address is to be assigned Basic Mapping Rule https://tools.ietf.org/html/rfc7597#section-5.2 IPv4 prefix length + ea bits length == 32 (o + r == 32) psid_length = 0, ip6_prefix < 64, ip4_prefix <= 32 PASS
TC03: BMR, shared IPv4 address is to be assigned Basic Mapping Rule https://tools.ietf.org/html/rfc7597#section-5.2 IPv4 prefix length + ea bits length > 32 (o + r > 32) ip6_prefix < 64, ip4_prefix <= 32 PASS
TC04: End user IPv6 prefix is 64 Supported End-User IPv6 prefix length is 64 bit. FAIL
TC05: IPv4 prefix is 0 FAIL
Bug: VPP-318 qlen < psid length FAIL
Bug: VPP-312 add route; add map; traffic pass; add route; add map; traffic fail FAIL

Map T

  • Test for Basic mapping rule for MAP-T
  • [Top] Network Topologies: TG - DUT1 - TG with two links between the nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP on TG-to-DUT-if1. Eth-IPv6-UDP on TG-to-DUT-if2.
  • [Cfg] DUT configuration: DUT is configured with IPv4 on one DUT-to-TG interface and IPv6 address on second DUT-to-TG interface. MAP-T domain is configured in test template based on test parameters.
  • [Ver] TG verification: UDP packets in IPv4 are sent by TG to destination in MAP domain. IPv6 packets with translated IPv4 addresses are received on TG interface.
  • [Ref] Applicable standard specifications: RFC7599
Name Documentation Status
TC01: MAP-T test Test to check map-t address translation. FAIL
Retrieved from "https://wiki.fd.io/index.php?title=CSIT/VPP-16.09_Test_Report_Draft&oldid=3247"