Difference between revisions of "ONE/Command-line Interface CLI Guide"
Florin.coras (Talk | contribs) (→Introduction) |
(→Telnet LISP CLI) |
||
| Line 8: | Line 8: | ||
== Telnet LISP CLI == | == Telnet LISP CLI == | ||
| − | === Lisp enable === | + | === Lisp GPE enable === |
| − | To enable lisp, use "lisp": | + | To enable lisp, use "lisp gpe": |
<pre> | <pre> | ||
| − | vpp# lisp enable | + | vpp# lisp gpe enable |
</pre> | </pre> | ||
To disable lisp | To disable lisp | ||
<pre> | <pre> | ||
| − | vpp# lisp disable | + | vpp# lisp gpe disable |
| + | </pre> | ||
| + | |||
| + | To display Lisp status: | ||
| + | <pre> | ||
| + | vat# show lisp status | ||
| + | feature: enabled | ||
| + | gpe: enabled | ||
</pre> | </pre> | ||
| Line 36: | Line 43: | ||
Locator-set Locator Priority Weight | Locator-set Locator Priority Weight | ||
ls1 6 1 1 | ls1 6 1 1 | ||
| + | </pre> | ||
| + | |||
| + | === Locator === | ||
| + | To add new locator, use "lisp locator add": | ||
| + | <pre> | ||
| + | vpp# lisp locator add locator-set ls1 iface host-intervpp1 p 1 w 1 | ||
| + | </pre> | ||
| + | Where <tt>locator-set</tt> is <tt>locator-set name</tt>, <tt>p</tt> is <tt>priority</tt> and <tt>w</tt> is <tt>weight</tt>. | ||
| + | |||
| + | To delete a specific locator_set, use "lisp locator del" | ||
| + | <pre> | ||
| + | vpp# lisp locator-set del locator-set ls1 iface host-intervpp1 p 1 w 1 | ||
</pre> | </pre> | ||
| Line 65: | Line 84: | ||
<pre> | <pre> | ||
vpp# lisp map-resolver del 6.0.3.100 | vpp# lisp map-resolver del 6.0.3.100 | ||
| + | </pre> | ||
| + | |||
| + | === Pitr === | ||
| + | To enable Pitr, use "lisp pitr": | ||
| + | <pre> | ||
| + | vpp# lisp pitr ls ls1 | ||
| + | </pre> | ||
| + | Where <tt>ls</tt> is <tt>locator-set name</tt> | ||
| + | |||
| + | To disable Pitr, use: | ||
| + | <pre> | ||
| + | vpp# lisp pitr disable ls ls1 | ||
| + | </pre> | ||
| + | |||
| + | To display pitr: | ||
| + | <pre> | ||
| + | vpp# show lisp pitr | ||
| + | pitr | ||
| + | disable | ||
| + | </pre> | ||
| + | |||
| + | === Remote-mapping === | ||
| + | To add new remote mapping use "lisp remote-mapping add": | ||
| + | <pre> | ||
| + | vpp# lisp remote-mapping add vni 0 eid 6.2.1.0/24 rloc 6.0.1.1 | ||
| + | </pre> | ||
| + | Where <tt>vni</vni> is <tt>Virtual Network Identifier</tt>, <tt>eid</tt> is <tt>eid prefix</tt> and <tt>rloc</tt> is <tt>remote locator</tt> | ||
| + | |||
| + | To disable remote mapping, use "lisp remote-mapping del": | ||
| + | <pre> | ||
| + | vpp# lisp remote-mapping del vni 0 eid 6.2.1.0/24 | ||
</pre> | </pre> | ||
Revision as of 08:43, 29 July 2016
Contents
Introduction
The vpp contain a set of commands to set and debug LISP. Access VPP's CLI over telnet, assuming cli-listen localhost:5002 is configured under unix{} in the startup.conf, with:
telnet 0 5002
Telnet LISP CLI
Lisp GPE enable
To enable lisp, use "lisp gpe":
vpp# lisp gpe enable
To disable lisp
vpp# lisp gpe disable
To display Lisp status:
vat# show lisp status feature: enabled gpe: enabled
Locator_set
To add new locator_set and locator, use "lisp locator-set add":
vpp# lisp locator-set add ls1 iface host-intervpp1 p 1 w 1
Where p is priority and w is weight.
To delete a specific locator_set, use "lisp locator-set del"
vpp# lisp locator-set del ls1
To display locator_set and locator:
vpp# show lisp locator-set
Locator-set Locator Priority Weight
ls1 6 1 1
Locator
To add new locator, use "lisp locator add":
vpp# lisp locator add locator-set ls1 iface host-intervpp1 p 1 w 1
Where locator-set is locator-set name, p is priority and w is weight.
To delete a specific locator_set, use "lisp locator del"
vpp# lisp locator-set del locator-set ls1 iface host-intervpp1 p 1 w 1
Eid
To add new Eid address, use "lisp eid-table":
vpp# lisp eid-table add eid 6.0.1.0/24 locator-set ls1
To delete a specific eid address, use "lisp eid-table del"
vpp# lisp eid-table del eid 6.0.1.0/24 locator-set ls1
To display eid table:
vpp# show lisp eid-table
EID Locator
6.0.2.0/24 ls1
Map resolver
To add new map resolver, use "lisp map-resolver":
vpp# lisp map-resolver add 6.0.3.100
To delete a specific map resolver address, use "lisp map-resolver del":
vpp# lisp map-resolver del 6.0.3.100
Pitr
To enable Pitr, use "lisp pitr":
vpp# lisp pitr ls ls1
Where ls is locator-set name
To disable Pitr, use:
vpp# lisp pitr disable ls ls1
To display pitr:
vpp# show lisp pitr
pitr
disable
Remote-mapping
To add new remote mapping use "lisp remote-mapping add":
vpp# lisp remote-mapping add vni 0 eid 6.2.1.0/24 rloc 6.0.1.1
Where vni</vni> is <tt>Virtual Network Identifier, eid is eid prefix and rloc is remote locator
To disable remote mapping, use "lisp remote-mapping del":
vpp# lisp remote-mapping del vni 0 eid 6.2.1.0/24
