Difference between revisions of "ONE/Command-line Interface CLI Guide"

From fd.io
< ONE
Jump to: navigation, search
(Telnet LISP CLI)
 
Line 6: Line 6:
 
</pre>
 
</pre>
  
== Telnet LISP CLI ==
+
== Telnet LISP CLI a.k.a debug CLI ==
 +
Following is a list of CLI commands used by LISP.
  
=== Lisp GPE enable ===
+
=== Enabling LISP ===
To enable lisp, use "lisp gpe":
+
For turning on LISP functionality type:
 
<pre>
 
<pre>
vpp# lisp gpe enable
+
vpp# lisp enable
 
</pre>
 
</pre>
  
To disable lisp
+
...and this will disable LISP
 
<pre>
 
<pre>
vpp# lisp gpe disable
+
vpp# lisp disable
 
</pre>
 
</pre>
  
To display Lisp status:
+
To display LISP status use
 
<pre>
 
<pre>
 
vat# show lisp status
 
vat# show lisp status
 
feature: enabled
 
feature: enabled
 
gpe: enabled
 
gpe: enabled
 +
</pre>
 +
where 'feature' field show status of LISP - both control plane and dataplane. 'gpe' is dataplane status indicator which can be enabled/disabled with its own set of commands:
 +
<pre>
 +
vat# lisp gpe enable
 +
vat# lisp gpe disable
 
</pre>
 
</pre>
  
=== Locator_set ===
+
=== Locator set ===
To add new locator_set and locator, use "lisp locator-set add":
+
To add new locator set and assigning locator(s) to it use "lisp locator-set add":
 
<pre>
 
<pre>
 
vpp# lisp locator-set add ls1 iface host-intervpp1 p 1 w 1
 
vpp# lisp locator-set add ls1 iface host-intervpp1 p 1 w 1
Line 33: Line 39:
 
Where <tt>p</tt> is <tt>priority</tt> and <tt>w</tt> is <tt>weight</tt>.
 
Where <tt>p</tt> is <tt>priority</tt> and <tt>w</tt> is <tt>weight</tt>.
  
To delete a specific locator_set, use "lisp locator-set del"
+
To delete a specific locator set, use "lisp locator-set del"
 
<pre>
 
<pre>
 
vpp# lisp locator-set del ls1
 
vpp# lisp locator-set del ls1
 
</pre>
 
</pre>
  
To display locator_set and locator:
+
To display current locator sets and their locators:
 
<pre>
 
<pre>
 
vpp# show lisp locator-set
 
vpp# show lisp locator-set
Line 46: Line 52:
  
 
=== Locator ===
 
=== Locator ===
To add new locator, use "lisp locator add":
+
To extend existing locator set with a new locator use "lisp locator add":
 
<pre>
 
<pre>
 
vpp# lisp locator add locator-set ls1 iface host-intervpp1 p 1 w 1
 
vpp# lisp locator add locator-set ls1 iface host-intervpp1 p 1 w 1
Line 52: Line 58:
 
Where <tt>locator-set</tt> is <tt>locator-set name</tt>, <tt>p</tt> is <tt>priority</tt> and <tt>w</tt> is <tt>weight</tt>.
 
Where <tt>locator-set</tt> is <tt>locator-set name</tt>, <tt>p</tt> is <tt>priority</tt> and <tt>w</tt> is <tt>weight</tt>.
  
To delete a specific locator_set, use "lisp locator del"
+
To delete a specific locator set, use "lisp locator del"
 
<pre>
 
<pre>
 
vpp# lisp locator-set del locator-set ls1 iface host-intervpp1 p 1 w 1
 
vpp# lisp locator-set del locator-set ls1 iface host-intervpp1 p 1 w 1
 
</pre>
 
</pre>
  
=== Eid ===
+
=== Manipulating EID table ===
To add new Eid address, use "lisp eid-table":
+
EID table contains mappings between EIDs and a locator sets. For adding an entry use following command:
 
<pre>
 
<pre>
 
vpp# lisp eid-table add eid 6.0.1.0/24 locator-set ls1
 
vpp# lisp eid-table add eid 6.0.1.0/24 locator-set ls1
 
</pre>
 
</pre>
 +
Currently an EID can be IPv4, IPv6 or MAC address.
  
To delete a specific eid address, use "lisp eid-table del"
+
To delete a specific entry from EID table use "lisp eid-table del"
 
<pre>
 
<pre>
vpp# lisp eid-table del eid 6.0.1.0/24 locator-set ls1
+
vpp# lisp eid-table del eid 6.0.1.0/24
 
</pre>
 
</pre>
  
To display eid table:
+
To list EID table use <tt>show lisp eid-table [local|remote] [eid <eid>]</tt>
 
<pre>
 
<pre>
vpp# show lisp eid-table
+
DBGvpp# show lisp eid-table
        EID             Locator   
+
EID                     type          locators            ttl      autoritative
6.0.2.0/24                   ls1
+
[0] 6.0.2.0/24           local(ls1)    host-xtr_rtr1      0        0
 
</pre>
 
</pre>
 +
It is also possible to specify a filter that will output only local or remote EID entries. You can also specify a EID entry that prints only info about it if found.
  
 
=== Map resolver ===
 
=== Map resolver ===
Line 86: Line 94:
 
</pre>
 
</pre>
  
=== Pitr ===
+
=== Proxy-ITR (PITR) ===
To enable Pitr, use "lisp pitr":
+
VPP can be used as a proxy ITR by specifying a locator set:
 
<pre>
 
<pre>
 
vpp# lisp pitr ls ls1
 
vpp# lisp pitr ls ls1
 
</pre>
 
</pre>
Where <tt>ls</tt> is <tt>locator-set name</tt>
+
Where <tt>ls</tt> is <tt>locator-set name</tt>.
  
To disable Pitr, use:
+
To disable PITR use:
 
<pre>
 
<pre>
 
vpp# lisp pitr disable ls ls1
 
vpp# lisp pitr disable ls ls1
 
</pre>
 
</pre>
  
To display pitr:
+
Following command tells if VPP is in PITR mode. If yes it also shows the name of locator set.
 
<pre>
 
<pre>
 
vpp# show lisp pitr
 
vpp# show lisp pitr
Line 105: Line 113:
 
</pre>
 
</pre>
  
=== Remote-mapping ===
+
=== Remote mapping ===
 +
This command provides a way to configure remote mappings programmed statically without a need of a map resolver.
 
To add new remote mapping use "lisp remote-mapping add":
 
To add new remote mapping use "lisp remote-mapping add":
 
<pre>
 
<pre>

Latest revision as of 15:13, 1 August 2016

Introduction

The vpp contain a set of commands to set and debug LISP. Access VPP's CLI over telnet, assuming cli-listen localhost:5002 is configured under unix{} in the startup.conf, with:

telnet 0 5002

Telnet LISP CLI a.k.a debug CLI

Following is a list of CLI commands used by LISP.

Enabling LISP

For turning on LISP functionality type:

vpp# lisp enable

...and this will disable LISP

vpp# lisp disable

To display LISP status use

vat# show lisp status
feature: enabled
gpe: enabled

where 'feature' field show status of LISP - both control plane and dataplane. 'gpe' is dataplane status indicator which can be enabled/disabled with its own set of commands:

vat# lisp gpe enable
vat# lisp gpe disable

Locator set

To add new locator set and assigning locator(s) to it use "lisp locator-set add":

vpp# lisp locator-set add ls1 iface host-intervpp1 p 1 w 1

Where p is priority and w is weight.

To delete a specific locator set, use "lisp locator-set del"

vpp# lisp locator-set del ls1

To display current locator sets and their locators:

vpp# show lisp locator-set
     Locator-set         Locator        Priority         Weight     
     ls1                      6               1               1

Locator

To extend existing locator set with a new locator use "lisp locator add":

vpp# lisp locator add locator-set ls1 iface host-intervpp1 p 1 w 1

Where locator-set is locator-set name, p is priority and w is weight.

To delete a specific locator set, use "lisp locator del"

vpp# lisp locator-set del locator-set ls1 iface host-intervpp1 p 1 w 1

Manipulating EID table

EID table contains mappings between EIDs and a locator sets. For adding an entry use following command:

vpp# lisp eid-table add eid 6.0.1.0/24 locator-set ls1

Currently an EID can be IPv4, IPv6 or MAC address.

To delete a specific entry from EID table use "lisp eid-table del"

vpp# lisp eid-table del eid 6.0.1.0/24

To list EID table use show lisp eid-table [local|remote] [eid <eid>]

DBGvpp# show lisp eid-table
EID                      type           locators            ttl       autoritative
[0] 6.0.2.0/24           local(ls1)     host-xtr_rtr1       0         0

It is also possible to specify a filter that will output only local or remote EID entries. You can also specify a EID entry that prints only info about it if found.

Map resolver

To add new map resolver, use "lisp map-resolver":

vpp# lisp map-resolver add 6.0.3.100

To delete a specific map resolver address, use "lisp map-resolver del":

vpp# lisp map-resolver del 6.0.3.100

Proxy-ITR (PITR)

VPP can be used as a proxy ITR by specifying a locator set:

vpp# lisp pitr ls ls1

Where ls is locator-set name.

To disable PITR use:

vpp# lisp pitr disable ls ls1

Following command tells if VPP is in PITR mode. If yes it also shows the name of locator set.

vpp# show lisp pitr
     pitr
    disable

Remote mapping

This command provides a way to configure remote mappings programmed statically without a need of a map resolver. To add new remote mapping use "lisp remote-mapping add":

vpp# lisp remote-mapping add vni 0 eid 6.2.1.0/24 rloc 6.0.1.1

Where vni</vni> is <tt>Virtual Network Identifier, eid is eid prefix and rloc is remote locator

To disable remote mapping, use "lisp remote-mapping del":

vpp# lisp remote-mapping del vni 0 eid 6.2.1.0/24