Difference between revisions of "ONE/BI and VAT Guide"

From fd.io
< ONE
Jump to: navigation, search
m (→‎LISP commands)
Line 101: Line 101:
 
     Map resolver     
 
     Map resolver     
 
     6:0:3::100
 
     6:0:3::100
 +
</pre>
 +
 +
=== Remote Mapping ===
 +
To add new remote mapping, use "lisp_add_del_remote_mapping"
 +
<pre>
 +
vat# lisp_add_del_remote_mapping add vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2
 +
</pre>
 +
 +
To delete specific remote mapping, use "lisp_add_del_remote_mapping del vni <vni> deid <ip prefix> seid <ip prefix> rloc <ip address>"
 +
<pre>
 +
lisp_add_del_remote_mapping del vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2
 +
</pre>
 +
 +
To display remote mapping use:
 +
<pre>
 +
vat# lisp_locator_set_dump                                                                                                                                                                                                                                                                 
 +
    Locator-set        Locator        Priority        Weight                                                                                                                                                                                                                             
 +
      remote-1        6.0.3.20/0          0              0                                                                                                                                                                                                                               
 +
vat#
 
</pre>
 
</pre>
  

Revision as of 11:07, 26 May 2016

Introduction

The vpp contain a set of commands to set and debug LISP. One way to access the VAT (with proper permissions) is to use the vpp_api_test command: 

sudo vpp_api_test


LISP commands

Lisp enable

To enable lisp, use "lisp_enable_disable": 

vat# lisp_enable_disable enable

To disable lisp. 

vat# lisp_enable_disable disable

To display lisp status 

vat# lisp_enable_disable_status_dump
    lisp
    enable

Locator_set

To add new locator_set, use "lisp_add_del_locator_set". This command also "reset" exist locator_set in vpp: 

vat# lisp_add_del_locator_set locator-set ls1

To delete a specific locator_set, use "lisp_add_del_locator_set locator-set <name> del": 

vat# lisp_add_del_locator_set locator-set ls1 del

When delete locator_set, then also delete all locator which are assigned to locator_set

To add new locator to locator_set, use "lisp_add_del_locator": 

vat# lisp_add_del_locator locator-set  ls1 iface GigabitEthernet0/a/0 p 1 w 2

Where p is priority and w is weight.

Locator API also support sw_if_index instead of interface name: 

lisp_add_del_locator locator-set  ls1 sw_if_index 6 p 1 w 2

To delete specific locator, use "lisp_add_del_locator locator-set <name> iface <interface> p <priority> w <weight> del" 

vat# lisp_add_del_locator locator-set  ls1 iface GigabitEthernet0/a/0 p 1 w 2 del

To display locator_set and locator: 

vat# lisp_locator_set_dump                                                                                                                                                                                                                                                                   
     Locator-set         Locator        Priority         Weight                                                                                                                                                                                                                              
         ls1                6               1               2


Eid

To add new Eid address, use "lisp_add_del_local_eid" 

vat# lisp_add_del_local_eid eid 6:0:1::0/64 locator-set ls1

There must exist locator_set, before add new eid address.

To delete specific eid address, use "isp_add_del_local_eid eid <address>/<prefix> locator-set <name>" 

vat# lisp_add_del_local_eid eid 6:0:1::0/64 locator-set ls1 del

To display Eid table: 

vat# lisp_local_eid_table_dump
     Locator-set                  Eid             
         ls1                  6.0.1.0/24          
         ls1                  6:0:1::/64


Map resolver

To add new map resolver, use "lisp_add_del_map_resolver" 

vat# lisp_add_del_map_resolver 6:0:3::100

To delete specific map resolver, use "lisp_add_del_map_resolver <ip address> del" 

vat# lisp_add_del_map_resolver 6:0:3::100 del

To display map resolver: 

vat# lisp_map_resolver_dump
    Map resolver    
     6:0:3::100

Remote Mapping

To add new remote mapping, use "lisp_add_del_remote_mapping" 

vat# lisp_add_del_remote_mapping add vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2

To delete specific remote mapping, use "lisp_add_del_remote_mapping del vni <vni> deid <ip prefix> seid <ip prefix> rloc <ip address>" 

lisp_add_del_remote_mapping del vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2

To display remote mapping use: 

vat# lisp_locator_set_dump                                                                                                                                                                                                                                                                   
     Locator-set         Locator        Priority         Weight                                                                                                                                                                                                                              
      remote-1         6.0.3.20/0           0               0                                                                                                                                                                                                                                 
vat#

Proxy-ITR

To add new proxy-itr, use "lisp_pitr_set_locator_set" 

vat# lisp_pitr_set_locator_set 6:0:3::100
Retrieved from "https://wiki.fd.io/index.php?title=ONE/BI_and_VAT_Guide&oldid=1510"