ONE/BI and VAT Guide
Contents
Introduction
The vpp contain a set of commands to set and debug LISP. One way to access the VAT (with proper permissions) is to use the vpp_api_test command:
sudo vpp_api_test
LISP commands
Lisp enable
To enable lisp, use "lisp_enable_disable":
vat# lisp_enable_disable enable
To disable lisp.
vat# lisp_enable_disable disable
To display lisp status
vat# lisp_enable_disable_status_dump
lisp
enable
Locator_set
To add new locator_set, use "lisp_add_del_locator_set". This command also "reset" exist locator_set in vpp:
vat# lisp_add_del_locator_set locator-set ls1
To delete a specific locator_set, use "lisp_add_del_locator_set locator-set <name> del":
vat# lisp_add_del_locator_set locator-set ls1 del
When delete locator_set, then also delete all locator which are assigned to locator_set
To add new locator to locator_set, use "lisp_add_del_locator":
vat# lisp_add_del_locator locator-set ls1 iface GigabitEthernet0/a/0 p 1 w 2
Where p is priority and w is weight.
Locator API also support sw_if_index instead of interface name:
lisp_add_del_locator locator-set ls1 sw_if_index 6 p 1 w 2
To delete specific locator, use "lisp_add_del_locator locator-set <name> iface <interface> p <priority> w <weight> del"
vat# lisp_add_del_locator locator-set ls1 iface GigabitEthernet0/a/0 p 1 w 2 del
To display locator_set and locator:
vat# lisp_locator_set_dump
Locator-set Locator Priority Weight
ls1 6 1 2
Eid
To add new Eid address, use "lisp_add_del_local_eid"
vat# lisp_add_del_local_eid eid 6:0:1::0/64 locator-set ls1
There must exist locator_set, before add new eid address.
To delete specific eid address, use "isp_add_del_local_eid eid <address>/<prefix> locator-set <name>"
vat# lisp_add_del_local_eid eid 6:0:1::0/64 locator-set ls1 del
To display Eid table:
vat# lisp_local_eid_table_dump
Locator-set Eid
ls1 6.0.1.0/24
ls1 6:0:1::/64
Map resolver
To add new map resolver, use "lisp_add_del_map_resolver"
vat# lisp_add_del_map_resolver 6:0:3::100
To delete specific map resolver, use "lisp_add_del_map_resolver <ip address> del"
vat# lisp_add_del_map_resolver 6:0:3::100 del
To display map resolver:
vat# lisp_map_resolver_dump
Map resolver
6:0:3::100
Remote Mapping
To add new remote mapping, use "lisp_add_del_remote_mapping"
vat# lisp_add_del_remote_mapping add vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2
To delete specific remote mapping, use "lisp_add_del_remote_mapping del vni <vni> deid <ip prefix> seid <ip prefix> rloc <ip address>"
lisp_add_del_remote_mapping del vni 0 deid 6.0.2.0/24 seid 6.0.1.0/24 rloc 6.0.3.2
To display remote mapping use:
vat# lisp_locator_set_dump
Locator-set Locator Priority Weight
remote-1 6.0.3.20/0 0 0
vat#
Proxy-ITR
To add new proxy-itr, use "lisp_pitr_set_locator_set"
vat# lisp_pitr_set_locator_set 6:0:3::100
